Ryobi RYi12VBGVNM Operation Manual

TTI OUTDOOR POWER EQUIPMENT, INC.

P.O. Box 1288, Anderson, SC 29622, USA

1-800-525-2579



www.ryobitools.com

120 WATT POWER SOURCE

RYi12VBGVNM

A - LED/Power button (témoin DEL/bouton d’alimentation, botón

LED/encendido )

B - LED light (éclairage DEL , Luz LED )

C - 12V Power Port (Port d'alimentation 12 V, Puerto de alimentación

de 12 voltios)

D - USB-A ports (ports USB-A, puertos USB A de)

E - USB-C port (port USB-C, puerto USB C)

F - USB-A Fast Charge ports (charge rapide ports USB-A, carga

rápida puertos USB A de)

A - LED/Power button (témoin DEL/bouton d’alimentation, botón

LED/encendido )

B - LED light (éclairage DEL , Luz LED )

Fig. 1

Fig. 3

Fig. 2

A - USB-A ports (ports USB-A, puertos USB A de)

B - USB product to be charged (not provided) [produit USB à charger

(non fourni), producto USB a cargar (no provisto)]

C - USB-A Fast Charge ports (charge rapide ports USB-A, carga

rápida puertos USB A de)

A - 12 volt DC port (port CC de 12 V, puerto de CC de 12 voltios)

B - 12 volt product to be charged (not provided) [appareil de 12 V à

charger (non fourni), producto de 12 voltios que desea cargar (no

proporcionado)]

A

A

B

B

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.



SAVE THESE INSTRUCTIONS

– This manual

contains important safety and operating instructions

for power source model RYi12VBGVNM.



Use this product only with batteries and chargers

listed in tool/appliance/battery pack/charger

correlation supplement 987000-432.



This product is for indoor use only.



Do not expose the power source to rain or wet

conditions.

Water entering the power source will

increase the risk of electric shock.



Do not disassemble the power source.



To reduce the risk of injury, close supervision

is necessary when an appliance is used near

children.



Store power source indoors and away from

children.



As with all electrical devices, use caution when

plugging and unplugging this unit into an outlet or

plugging/unplugging other devices into this unit.

Do not force this unit into an outlet. Do not force plugs

into this unit.



To reduce the risk of damage to electric plug

and cord,

pull by plug rather than cord when

disconnecting power source.



If this unit is used in a manner not specified by

the manufacturer,

the protection provided by this

equipment may be impaired.



Do not use the power source if it has been dropped

or received a sharp blow. A damaged power source

will increase the risk of fire



Do not overload the power source.

It must be used

for powering devices less than the product rating.



Operate this product using only the power type

listed in the product specifications.



Never block air vents.

Blocked vents may cause

overheating. Power source will automatically shut off

when overheated.



Keep power source cool.

Do not place near heat

vents or in direct sunlight.



Remove the battery pack from power source when

not in use.



Do not use the power source around flammable

fumes and gasses, such as in the bilge of a boat

or near propane tanks.



Do not use in an enclosed area with automotive

lead acid batteries.



Do not put foreign objects into the power source.

WARNING:

The power source is not intended for any use other

than charging small USB A, USB C, or 12V devices.

Any other use may result in risk of fire or electric

shock.



Do not power life support devices or other

necessary medical equipment with this tool.



This unit should never be hard wired into a circuit.



Do not attempt to set up, make adjustments or

power devices while operating a vehicle.



Save these instructions.

Refer to them frequently

and use them to instruct others who may use this

product. If you loan someone this product, loan them

these instructions also.

PRODUCT SPECIFICATIONS

Watts

........................................

Continuous 120 Watts

DC Input

....................................................

18 Volts DC

USB A Fast Charge Ports Output

......................

5V(3A),

9V(2A), 12V(1.5A) (Shared) DC

USB A Ports Output

..................

5V (2.4A) (Shared) DC

USB C PD Port Output

........................

5V(3A), 9V(3A),

12V(2.5A), 15V(2A), 20V(1.5A) DC

12V Power Port

........................................

12V(10A) DC

OPERATION

APPLICATIONS

You may use this product for the following purposes:



Operating and charging USB-powered or 12V devices



Supplying electrical power for operating compatible

electrical lighting, appliance, tool, or motor load.

WARNING:

Risk of electric shock.

Do not allow water or any

liquid to get inside the Power Source. Electric shock

may result.

INSTALLING/REMOVING BATTERY PACK

See Figure 1.



To install:

insert a battery pack into the power source

as shown. Make sure the latches on the battery pack

snap into place and the battery pack is secured in the

power source before beginning operation.



To remove:

depress the latches on the battery pack.

USING THE POWER SOURCE

See Figure 2-4



Insert a battery pack into the power source.



Press and hold the power button (

) for 1.5 seconds

to turn the power source

ON

. The LED will light up

green when ready to use.



Plug devices you want to power or charge into the

power source’s USB ports and/or 12V plug receptacle.



If the power button LED blinks red then turns off,

the power source may be overloaded. Disconnect

your device, make sure your battery pack is

sufficiently charged to power your device, then

press the button to turn the power source back on.

Reconnect your device and try again. If the fault

condition immediately reoccurs, the item being

powered exceeds the capacity of the power source.



If the power button LED turns red but does not

shut down the power source, the power source

is overheated. Allow the unit to cool until the LED

turns green, then try again.



If the power button LED flashes yellow, the battery

pack needs to be recharged.



To use the worklight, double press the power button

(

) . Double press the power button again to turn

the worklight off.

NOTE:

The power source must be on for the worklight

to function.



When finished, disconnect your device and press the

power button indicator (

) again for 1.5 seconds to

turn off the power source.

NOTE:

When needed, an internal cooling fan will run

to regulate the unit’s operating temperature. If running,

always wait for the fan to stop before you disconnect

the battery pack from the power source.

WARRANTY

This product has a Three-year Limited Warranty

for personal, family, or household use

(90 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-525-2579.

FCC COMPLIANCE

WARNING:

Changes or modifications to this unit not expressly

approved by the party responsible for compliance

could void the user’s authority to operate the

equipment.

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received, includ-

ing interference that may cause undesired operation.

NOTE:

The grantee is not responsible for any changes

or modifications not expressly approved by the party

responsible for compliance. Such modifications could

void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harm-

ful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and

receiver.



Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.



Consult the dealer or an experienced radio/TV

technician for help.

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interfer-

ence, including interference that may cause undesired

operation of the device.

Under Industry Canada regulations, this radio transmit-

ter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference to

other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful

communication

Model/item number on product may have

additional letters at the end. These letters designate

manufacturing information and should be provided

when calling for service.

ILLUSTRATIONS / ILLUSTRÉES / ILUSTRADAS

OPERATOR’S

MANUAL

Fig. 4

A - Battery pack (not included) [bloc-piles (non inclus), paquete de

baterías (no suministrado)]

B - Depress latches to release battery pack (appuyer sur les loquets

pour libérer le bloc-piles, para soltar el paquete de baterías

oprima los pestillos)

C - Power source (convertisseur de current, inversor de corriente)

A

D

E

C

A

B

C

B

B

B

A

F

C

998000574

11-12-21 (REV:04)

Ryobi RYi12VBGVNM Operation Manual

Ryobi RYi12VBGVNM Manual

Ryobi RYi12VBGVNM manual content summary: