Ryobi TS1344L User Manual

Ryobi TS1344L Manual

Get Ryobi TS1344L PDF manuals and user guides View all Ryobi TS1344L manuals
Add to My Manuals
Save this manual to your list of manuals

Ryobi TS1344L manual content summary:

  • Ryobi TS1344L | User Manual - Page 1
    OPERATOR'S MANUAL 10 in. Compound Miter Saw TS1344L - Double Insulated Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To
  • Ryobi TS1344L | User Manual - Page 2
    first 90 days after date of purchase, you may either request service under this warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or materials by returning the power tool to the dealer from which it was purchased. To receive a replacement
  • Ryobi TS1344L | User Manual - Page 3
    sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.  DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power source.  AVOID ACCIDENTAL
  • Ryobi TS1344L | User Manual - Page 4
    injury. Instructions for safe use of accessories are included with the accessory.  DOUBLE CHECK ALL SETUPS. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply. SPECIFIC SAFETY RULES  FIRMLY CLAMP OR BOLT your tool to a workbench or table at
  • Ryobi TS1344L | User Manual - Page 5
    wait for saw blade to stop before moving workpiece or changing settings. g) Disconnect power (or unplug tool as applicable) before changing blade or servicing. h) No load speed.  ALWAYS carry the tool only by the "D" handle.  AVOID direct eye exposure when using the laser guide.  THIS SAW CAN TIP
  • Ryobi TS1344L | User Manual - Page 6
    their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Safety Alert Precautions that involve your safety. Read Operator's Manual Eye Protection To reduce the risk of injury, user must read and understand
  • Ryobi TS1344L | User Manual - Page 7
    and should be performed only by a qualified service technician. For service, we suggest you return the tool to the nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELECTRICAL CONNECTION This tool has a precision-built electric motor. It
  • Ryobi TS1344L | User Manual - Page 8
    blades or knives. The blades or knives remove material from the workpiece. Dado Cut (table saws and compound sliding miter saws) A non-through cut which produces a square, three-sided notch or trough in the workpiece. Featherboard (table saws) A device used to help control the workpiece by guiding
  • Ryobi TS1344L | User Manual - Page 9
    Maximum nominal lumber sizes 2 x 6 Cutting Capacity with Miter at 45°/Bevel 45°: Maximum nominal lumber sizes 2 x 4 UPPER BLADE GUARD "D" HANDLE DUST BAG BLADE WRENCH BEVEL LOCK KNOB MITER FENCE MITER TABLE BASE SWITCH TRIGGER LOWER BLADE GUARD THROAT PLATE "NO HANDS ZONE" BOUNDARY LINE
  • Ryobi TS1344L | User Manual - Page 10
    MITER SAW See Figure 1. The safe use of this product requires an understanding of the information on the tool and in this operator's manual has externally accessible brushes for ease of servicing. 10 in. BLADE A 10 in. blade is included with the compound miter saw. It will cut materials up to 3-1/2
  • Ryobi TS1344L | User Manual - Page 11
    3. The spindle lock button locks the spindle stopping the blade from rotating. Depress and hold the lock button while installing, changing, or removing blade. SWITCH TRIGGER See Figure 4. To prevent unauthorized use of the compound miter saw, disconnect it from the power supply and lock the switch
  • Ryobi TS1344L | User Manual - Page 12
    LOOSE PARTS The following items are included with the tool:  Miter Lock Handle  Dust Bag  Work Clamp  Blade Wrench  AAA Batteries  Operator's Manual DUST BAG AAA BATTERIES BLADE WRENCH WORK CLAMP MITER LOCK HANDLE Fig. 6 WARNING: The use of attachments or accessories not listed might be
  • Ryobi TS1344L | User Manual - Page 13
    have carefully inspected and satisfactorily operated the tool.  The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in this manual.  If any parts are damaged or missing, please call
  • Ryobi TS1344L | User Manual - Page 14
    dust bag is provided for use on the miter saw. It fits over the exhaust port on the upper blade guard. Squeeze the two metal clips to miter table base.  Rotate the knob on the work clamp clockwise to move it in or counterclockwise to move it out as needed. DUST BAG TO TIGHTEN CONTROL ARM MITER
  • Ryobi TS1344L | User Manual - Page 15
    screw from battery compartment cover using the Phillips end of the supplied blade wrench. Remove cover and set aside.  Install two AAA radiation exposure. ALIGNING THE LASER GUIDE LINE See Figure 12. Unplug the saw. Draw a line on the workpiece. When the laser guide switch is turned on it will
  • Ryobi TS1344L | User Manual - Page 16
    14. WARNING: A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow laser guide washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the
  • Ryobi TS1344L | User Manual - Page 17
    handle.  Lay a framing square flat on the miter table. Place one leg of the square against the fence. Slide the other leg of the square against the flat part of saw blade. NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.  The edge of the square and the
  • Ryobi TS1344L | User Manual - Page 18
    ASSEMBLY MITER FENCE BLADE MITER SCALE SCALE INDICATOR MITER TABLE FRAMING SQUARE MITER LOCK HANDLE VIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED Fig. 17 MITER FENCE BLADE INDICATOR SCREW BEVEL SCALE SCALE INDICATOR INDICATOR SCREW Fig. 19 BLADE MITER TABLE FRAMING
  • Ryobi TS1344L | User Manual - Page 19
    bevel lock knob.  Place a combination square against the miter table and the flat part of saw blade. NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.  Rotate the blade by hand and check the blade-to-table alignment at several points.  The edge of the
  • Ryobi TS1344L | User Manual - Page 20
    but for fine joinery cuts or cutting plastic, use one of the accessory blades available from the Ryobi dealer. WARNING: Before starting any cutting operation, clamp or bolt the compound miter saw to a workbench. Never operate the miter saw on the floor or in a crouched position. Failure to heed this
  • Ryobi TS1344L | User Manual - Page 21
    30 - 31.  When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the miter table. See Figure 28.  Align cutting line on workpiece with edge of saw blade or laser line.  Grasp the stock firmly with one hand and
  • Ryobi TS1344L | User Manual - Page 22
    the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade.  When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the miter table. See Figure 28.  Align the cutting line on
  • Ryobi TS1344L | User Manual - Page 23
    the workpiece.  Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table. TO SUPPORT LONG WORKPIECES See Figure 28. Long workpieces need extra
  • Ryobi TS1344L | User Manual - Page 24
    OPERATION CUTTING COMPOUND MITERS To aid in making the correct settings, the compound ° M- 0.00° M- 0.00° B- 45.00° B- 36.00° B- 30.00° B- 25.71° B- 22.50° B- 20.00° B- 18.00° Each B (Bevel) and M (Miter) Setting is Given to the Closest 0.005°. COMPOUND-ANGLE SETTINGS FOR POPULAR STRUCTURES 24
  • Ryobi TS1344L | User Manual - Page 25
    miter table and against the fence. When setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes . The crown molding is placed flat on the miter table using the compound features of your miter saw. 52° 38° CEILING W A L L
  • Ryobi TS1344L | User Manual - Page 26
    - 31. When cutting warped material, always make sure it is positioned on the miter table with the convex side against the fence as shown in figure 30. If the is positioned the wrong way as shown in figure 31, it will pinch the blade near the completion of the cut. WRONG Fig. 31 WARNING: To avoid a
  • Ryobi TS1344L | User Manual - Page 27
    movement is tight or if there is play in the pivot, have saw repaired at your nearest RYOBI AUTHORIZED SERVICE CENTER. DEPTH STOP The depth stop limits the blade's downward travel. It allows the blade to go below the miter table enough to maintain full cutting capacities. The depth stop is factory
  • Ryobi TS1344L | User Manual - Page 28
    TO ADJUST THE LASER GUIDE See Figure 34.  Use the work clamp or a C-clamp to secure a piece of scrap wood.  Plug the saw into the power source the saw blade to stop rotating before raising the blade.  Raise the saw arm.  Unplug the saw.  Using the Phillips end of the supplied blade wrench,
  • Ryobi TS1344L | User Manual - Page 29
    MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts can create a hazard or cause product damage. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation. If
  • Ryobi TS1344L | User Manual - Page 30
    of this tool will be found on a plate attached to the motor housing. Please record the model number and serial number in the space provided below. • HOW TO ORDER REPAIR PARTS When ordering repair parts, always give the following information: • MODEL NUMBER TS1344L • SERIAL NUMBER RYOBI is
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
10 in. Compound Miter Saw
TS1344L - Double Insulated
Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.