Samsung RF260BEAESR User Manual Ver.1.0 (English, French, Spanish) - Page 7

Accessories And, Required Tools, Removing The, Refrigerator Doors

Get Samsung RF260BEAESR PDF manuals and user guides View all Samsung RF260BEAESR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

01 setting up FLOORING For proper installation, you must place this refrigerator on a level, hard surface that is the same height as the rest of the floor. This surface should be strong enough to support a fully loaded refrigerator, or approximately 331lbs (150kg). To protect the finish of the flooring, cut a large section of the cardboard carton and place it under the refrigerator where you are working. When moving the refrigerator, you need to pull and push it straight forwards or back. Do not wiggle it from side to side. Removing the refrigerator doors For some installations you need to remove the fridge and freezer drawers so you can move the refrigerator to its final location. Do not remove the doors/drawer if you don't need to. If you do not need to remove the refrigerator doors, go to Adjusting the Level on page 9. If you need to remove the doors. continue below. Before removing the door/drawer, make sure you read the following items: Disconnect power to the refrigerator before WARNING removing the door or drawer. Accessories and required tools The following accessories are included with your refrigerator: •• Be careful not to drop, damage or scratch the door/drawer while removing them. •• Be careful not to get injured while removing the door/drawer. •• Reattach the door/drawer properly to avoid: -- Moisture from air leakage. -- Uneven door alignment. -- Wasting energy due to improper door seal. Disassemble the refrigerator doors Be careful not to drop and scratch the WARNING doors while removing the doors. With the door opened 111 Remove 3 screws holding down the TOP TABLE ( 1 ) and turn it with wires connected. Hex wrench Fastener 1 Required Tools (Not provided) You need the following tools to complete the installation of your refrigerator: Philips Flat-blade screw Socket wrench screwdriver(+) driver(-) (10mm) 222 Disconnect two connector ( 2 ) on the left side door. To remove the water coupler from the hinge, twist and pull it from the hinge. 2 Pliers Allen wrench (3/16") (5mm) setting up _07 DA68-02601B(EN+ES+FR)-0.0.indb 7 2012.3.29 9:28:31 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
setting up
_07
01 SETTING UP
FLOORING
For proper installation, you must place this
refrigerator on a level, hard surface that is the
same height as the rest of the floor. This surface
should be strong enough to support a fully loaded
refrigerator, or approximately 331lbs (150kg).
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working. When
moving the refrigerator, you need to pull and push
it straight forwards or back. Do not wiggle it from
side to side.
ACCESSORIES AND
REQUIRED TOOLS
The following accessories are included with your
refrigerator:
Hex wrench
Fastener
Required Tools (Not provided)
You need the following tools to complete the
installation of your refrigerator:
Philips
screwdriver(+)
Flat-blade screw
driver(-)
Socket wrench
(10mm)
Pliers
Allen wrench
(3/16”) (5mm)
REMOVING THE
REFRIGERATOR DOORS
For some installations you need to remove the
fridge and freezer drawers so you can move the
refrigerator to its final location. Do not remove
the doors/drawer if you don’t need to. If you do
not need to remove the refrigerator doors, go
to Adjusting the Level on page 9. If you need to
remove the doors. continue below.
Before removing the door/drawer, make sure you
read the following items:
Disconnect power to the refrigerator before
removing the door or drawer.
Be careful not to drop, damage or
•
scratch the door/drawer while removing
them.
Be careful not to get injured while removing the
•
door/drawer.
Reattach the door/drawer properly to avoid:
•
Moisture from air leakage.
-
Uneven door alignment.
-
Wasting energy due to improper door seal.
-
Disassemble the refrigerator doors
Be careful not to drop and scratch the
doors while removing the doors.
With the door opened
Remove 3 screws holding down the
TOP
1.
TABLE
(
1
) and turn it with wires connected.
Disconnect two connector (
2.
2
) on the left side
door. To remove the water coupler from the
hinge, twist and pull it from the hinge.
WARNING
WARNING
2
1
DA68-02601B(EN+ES+FR)-0.0.indb
7
2012.3.29
9:28:31 AM