Samsung SCC-C7478C User Guide

Samsung SCC-C7478C Manual

Get Samsung SCC-C7478C PDF manuals and user guides View all Samsung SCC-C7478C manuals
Add to My Manuals
Save this manual to your list of manuals

Samsung SCC-C7478C manual content summary:

  • Samsung SCC-C7478C | User Guide - Page 1
    ENG FRC SPA-M POR-B JAP SCC-C7478 36x Smart Dome Camera User's Guide imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/global/register
  • Samsung SCC-C7478C | User Guide - Page 2
    must be securely attached to the floor/wall in accordance with the installation instructions. • If this power supply is used at 240V ac, a suitable plug contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized
  • Samsung SCC-C7478C | User Guide - Page 3
    . This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
  • Samsung SCC-C7478C | User Guide - Page 4
    not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, to avoid injury from tip-over. 14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
  • Samsung SCC-C7478C | User Guide - Page 5
    Contents ENG Introduction Features 6 Product & Accessories 7 Parts Name & Functions 8 Installation DIP Switch Setup 9 Installation using Mount Bracket 10 Cabling 13 Operation Check points before operation 15 Preset and Pattern Function Pre-Check 15 AUTO CALIBRATION 15 Starting
  • Samsung SCC-C7478C | User Guide - Page 6
    ICR(IR Cut filter Removal) • Various Focus Mode : Auto Focus / Manual Focus / Semi-Auto Focus. • Independent or Global camera settings for each Preset of cameras can be controlled at the same time. • Pelco-D/ Pelco-P/ Samsung protocol can be selected as a control protocol in the current version of fi
  • Samsung SCC-C7478C | User Guide - Page 7
    PRODUCT & ACCESSORIES ❖ Product  Wall Mount Type Introduction Ceiling Mount Type ENG ❖ Accessories  Hexagonal wrench Anchor bolts (4pcs) Water proof tape Housing Safety Cable Hanger Hole Template User's Guide Safety Cable English - 7
  • Samsung SCC-C7478C | User Guide - Page 8
    sunshield, there is the upper housing which will contain accommodate PTZ mechanism. Also, the upper housing will be connected to both mounting brackets and dome cover. • Wall/Ceiling mount Bracket These are used to install the camera on the wall or ceiling and have junction box. The junction box of
  • Samsung SCC-C7478C | User Guide - Page 9
    Pin1 Pin2 Pin3 Pin4 Protocol OFF OFF OFF OFF Auto Protocol ON OFF OFF OFF PELCO-D OFF ON OFF OFF PELCO-P ON ON OFF OFF SAMSUNG • If you set the protocol as Auto Protocol, camera will automatically recognize the kind of Protocol. • If you want to control using DVR or system
  • Samsung SCC-C7478C | User Guide - Page 10
    485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of Off) INSTALLATION USING MOUNT BRACKET ① Using the paper template, mark the holes on the wall. ③ After locating the wall mount bracket on the
  • Samsung SCC-C7478C | User Guide - Page 11
    ⑤ After hooking the safety cable on the hole of pipe [1], attach the upper housing to wall mount bracket by turning it at least seven turns [2]. To fix the upper body orientation, turn the handle of double nuts to clockwise tightly [3]. Installation ⑦ Plug the
  • Samsung SCC-C7478C | User Guide - Page 12
    Installation ⑨ Close the dome cover. Care must be taken to locate dome cover by matching the "Arrow" mark. ⑩ Tighten four screws on the dome cover in sequence as shown in the picture bellow 4 ‫ٻ‬ 1 2 ‫ٻ‬ 3 To maintain the best sealing, the torque of each screw must be in the range between 0.5
  • Samsung SCC-C7478C | User Guide - Page 13
    CABLING DVR/ Keyboard RS-485 D+ D- D+ D- Installation Connector to the dome camera ALARM OUTPUT 12 34 ALARM INPUT 1 2 3 4 G5 6 7 8 POWER NC. BNC VIDEO Monitor ❖ Power Connection • Please, check the voltage and current capacity of rated power carefully. Rated Power AC 24V Input Voltage
  • Samsung SCC-C7478C | User Guide - Page 14
    Installation ❖ Video Connection • Connect with BNC coaxial cable. ❖ Alarm Input Connection • Sensor Input IN 1 INTERNAL IN 2 IN 3 IN 4 GND IN 5 IN 6 IN 7 IN 8 • Alarm Output There are 4 Alarm Outputs and all of them are Relay contact type. Therefore, you do not have to care about polarity, AC/DC,
  • Samsung SCC-C7478C | User Guide - Page 15
    be checked in the System Information of OSD Menu. • If your controller supports multi-protocols, the protocol must be changed to match to that of the method can be different for each controller available, refer to the manual for your controller if camera can not be controlled properly. PRESET
  • Samsung SCC-C7478C | User Guide - Page 16
    Operation PRESET • Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset and they are adjusted by
  • Samsung SCC-C7478C | User Guide - Page 17
    Operation ENG SCAN • Function The Scan function allows running sequence of Presets, Pattern and/or Auto Pans. Max 8 Scan can be stored. Each Scan can have max 20 action entities which can be preset, pattern or Auto Pan. Preset speed can be set up and the repeat number of Pattern & Auto Pan can be
  • Samsung SCC-C7478C | User Guide - Page 18
    WB/AE value will not be changed although General WB/AE value change. • Semi Auto Focus This mode exchanges focus mode automatically between Manual Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation. With
  • Samsung SCC-C7478C | User Guide - Page 19
    sets all data to factory default configuration. SYSTEM INFORMATION SYSTEM INFORMATION FIRMWARE VER COLOR SYSTEM PROTOCOL BAUD RATE ADDRESS 1.00S36 NTSC SAMSUNG 9600 255 • Baud rate • Address Shows current Baud rate of PTZ control. Shows current Camera ID for PTZ control. DISPLAY SETUP DISPLAY
  • Samsung SCC-C7478C | User Guide - Page 20
    How to use OSD Menu • Display [ON/OFF] Sets if camera makes mask shows or not on images. • Clear Mask [CANCEL/OK] Deletes data in the selected mask NO. ❖ Privacy Zone Area Setup EDIT MASK 1 MOVE TO TARGET POSITION [NEAR:SELECT/FAR:CANCEL] 0/0/x1/N Move camera to area to mask. Then the menu
  • Samsung SCC-C7478C | User Guide - Page 21
    to move slowly between two preset points. • Pattern Setup Up to 4 patterns can be stored in the dome. In this function, path data created by manual move of Joystick are recorded and you can playback the identical path automatically whenever required. • Scan Setup Up to 8 Scans can be defined. In
  • Samsung SCC-C7478C | User Guide - Page 22
    How to use OSD Menu PRESET SETUP PRESET SETUP PRESET NO. 1 CLR PRESET CAM ADJUST ALARM OUT WINDOWS CANCEL GENERAL ---- BACK EXIT • Preset Number [1~128] If a selected preset is already defined, camera moves to pre-defined position and preset characteristics such as Label
  • Samsung SCC-C7478C | User Guide - Page 23
    ENG How to use OSD Menu Back Space Char. Space Char. If you want to use blank, choose Space character (" "). If you want to delete a character before, use back space character (" "). ③ If you complete the Label editing, move cursor to "OK" and press NEAR or ENTER key to save completed label. To
  • Samsung SCC-C7478C | User Guide - Page 24
    How to use OSD Menu ❖ Edit Pattern ① By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR or ENTER key. To exit this menu, press FAR key. EDIT PATTERN 1 SCAN SETUP SCAN SETUP SCAN NO. CLEAR SCAN 1 UNDEFINED CANCEL MOVE TO START
  • Samsung SCC-C7478C | User Guide - Page 25
    How to use OSD Menu ③ Set up Action, Dwell time and Option. Note that selected item is displayed in reverse. Move cursor Left/Right to select items and move cursor Up/Down to change each value. EDIT SCAN 1 NO. ACTION NO. DWELL OPT 1 NONE 2 NONE 3 NONE 4 NONE 5 NONE SAVE [◄ ►:MOVE CURSOR]
  • Samsung SCC-C7478C | User Guide - Page 26
    , you can make various schedules. For example, PRS179 are PRS178 are Day and Night mode respectively. (Refer to Reserved Preset(page 15) List in this manual.) 26 - 36x SMART DOME CAMERA
  • Samsung SCC-C7478C | User Guide - Page 27
    sec. ❖ White Balance Setup WB SETUP - GLOBAL WB MODE zRED ADJUST zBLUE ADJUST AUTO ----- BACK EXIT • WB Mode [AUTO/MANUAL] In Manual mode, Red and Blue level can be set up manually • Red Adjust [0~255] • Blue Adjust [0~255] ❖ Auto Exposure Setup AE SETUP WDR/BLC DAY/NIGHT AE MODE „ IRIS
  • Samsung SCC-C7478C | User Guide - Page 28
    F16/F19/F22/F28. (18 steps) • GAIN [Works when AE MODE is MANUAL] Enhances image brightness automatically in case that luminance level of image signal is too 20/22/24/26/ 28dB (16 steps) • Shutter Speed [Works when AE MODE is MANUAL or SHUTTER mode] X64, X32, X16, X8, X4, X2,1/60,1/90,1/100,1/125,1/
  • Samsung SCC-C7478C | User Guide - Page 29
    ENG How to use OSD Menu EDIT PASSWORD 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz OK CANCEL DISABLE • Password Setup You can define 4 characters long password. If this function is set to ENABLE, it is required to type this password whenever to enter OSD MENU. It is
  • Samsung SCC-C7478C | User Guide - Page 30
    How to use OSD Menu SYSTEM INITIALIZE SYSTEM INITIALIZE CLEAR ALL DATA NO „ CLR DISPLAY SET NO „ CLR CAMERA SET NO „ CLR MOTION SET NO „ CLR FUNCTION SET NO REBOOT CAMERA NO REBOOT SYSTEM NO BACK EXIT • Clear All Data Deletes all configuration data such as display, camera, motion
  • Samsung SCC-C7478C | User Guide - Page 31
    Tilt Speed Preset Pattern Auto Pan Scan Auto/Manual(-3 ~ 28dB) Auto / Manual(Red, Blue Gain Adjustable) WDR On/Off Auto, Pelco-D, Pelco-P, Samsung selectable Privacy Zone 8 Support 7 Languages: [ENGLISH /ESPAÑOL /FRANÇAIS /DEUTSCH/ITALIANO PORTUGUÊS] SCC-C7478N : AC 24V ± 10% (60Hz ± 0.3Hz) SCC
  • Samsung SCC-C7478C | User Guide - Page 32
    Specifications DIMENSION  • Wall Mount Bracket Unit (mm) • Ceiling Mount Bracket 32 - 36x SMART DOME CAMERA
  • Samsung SCC-C7478C | User Guide - Page 33
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
36x Smart Dome Camera
User’s Guide
SCC-C7478
imagine
the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/global/register
ENG
FRC
SPA-M
POR-B
JAP