Samsung STP-103 User Manual

Samsung STP-103 Manual

Get Samsung STP-103 PDF manuals and user guides View all Samsung STP-103 manuals
Add to My Manuals
Save this manual to your list of manuals

Samsung STP-103 manual content summary:

  • Samsung STP-103 | User Manual - Page 1
    USER'S MANUAL STP-103 THERMAL PRINTER KN04-00003A Rev. 2.6 POWER ERROR FEED ON LINE www.samsungminiprinters.com
  • Samsung STP-103 | User Manual - Page 2
    the cable by force or leave it under any heavy object. A damaged cable can cause a fire. PROHIBITED TO UNPLUG PRINTER WARNING Violating following instructions can yourself. Call your dealer when you need these services. Do not use the printer when it is out of order. This can cause a fire
  • Samsung STP-103 | User Manual - Page 3
    noise thermal printing. 3. RS-232 serial interface (STP-103S), Parallel interface (STP-103P). 4. The data buffer allows the unit to receive print data even during printing. 5. Different print densities can be selected by DIP switches. Please be sure to read the instruction in this manual carefully
  • Samsung STP-103 | User Manual - Page 4
    29 APPENDIX A - Connectors 51 - Serial Type (STP-103S 51 - Parallel Type (STP-103P 51 APPENDIX B - Specification 52 ※Option : STP-103DK 53 6 Chapter 1. Unpacking 1-1. Checking the contents of the Printer The items illustrated below are included with your printer. If any items are damaged or
  • Samsung STP-103 | User Manual - Page 5
    paper (11) Detector switch (5) (1) Rear View (2) (4) Rear View (6) (7) (8) STP-103S Control Panel POWER ERROR FEED ON LINE (3) (9) STP-103P on printer conditions. POWER (green) The POWER light is on when the printer power is on. ERROR (red) 1) The error LED blinks fast when paper is
  • Samsung STP-103 | User Manual - Page 6
    . 3. Plug the power supply's DC cable connector into the printer's power connector as shown below. STP-103S / STP-103P 2-2. Connecting the printer to your Computer STP-103S You need an appropriate serial interface cable to connect your computer to the printer's built-in interface. 1. Make sure
  • Samsung STP-103 | User Manual - Page 7
    2-2. Connecting the printer to your Computer STP-103P You need an appropriate parallel interface cable to connect your computer to the printer's built-in interface. 1. Make sure that both the printer and computer are turned off : then plug the cable connector securely into the printer's interface
  • Samsung STP-103 | User Manual - Page 8
    while setting the DIP switch to prevent an electrical short, which can damage the printer. You can change your interface and printer density settings by changing the DIP switch setting. 1. Make sure the printer is turned off. 2. There are a switch. Notice that ON is marked on each set of switches
  • Samsung STP-103 | User Manual - Page 9
    see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hexadecimal dump function, the printer prints all commands and data in hexadecimal format along with a guide section to help you find specific commands. To use the hexadecimal dump
  • Samsung STP-103 | User Manual - Page 10
    Chapter 7. Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count across the top of the table for the For example, 4A=J. # PC437 : USA, Standard Europe 18 Page1 : KATAKANA 19
  • Samsung STP-103 | User Manual - Page 11
    PC850 : Multilingual 20 PC860 : Portuguese 21
  • Samsung STP-103 | User Manual - Page 12
    PC863 : Canadian - French 22 PC865 : Nordic 23
  • Samsung STP-103 | User Manual - Page 13
    PC858: Euro 24 SP Space Page 25
  • Samsung STP-103 | User Manual - Page 14
    /off Select 1/6-inch line spacing Set line spacing Select peripheral device Cancel user-defined characters Initialize printer Set horizontal tab positions Turn emphasized mode on/off Print and feed paper Select an international character set Turn 90 clockwise rotation mode on/off Set relative print
  • Samsung STP-103 | User Manual - Page 15
    Esc d Esc t Esc { Enable/disable panel FEED buttons Print and feed paper n lines Select character code table Turn upside-down printing mode on/off command. [Notes] Provides important information on setting and using the printer command, it necessary. [Default] Gives the default values, if
  • Samsung STP-103 | User Manual - Page 16
    On 10 16 Not used. Fixed to On. 5,6 Off 00 0 Paper roll sensor. Paper present. On 60 96 Paper roll end detected by paper roll sensor 7 Off 00 0 Not used. Fixed to Off. DLE ENQ n [Name] Real time request to printer [Format] ASCII DLE ENQ n HEX 10 05 n DECIMAL 16 5 n [Range
  • Samsung STP-103 | User Manual - Page 17
    ≤ 3 , 0 ≤ d ≤ 255 [Description] Selects a bit-image mode using m for the number of dots specified by nL and nH, as follows: Vertical Direction Horizontal Direction(*1) m Mode Number of Dots Dots Density Dots Density Number of Data (k) 0 8-dot single-density 8 67 DPI 100 DPI nL + nH × 256
  • Samsung STP-103 | User Manual - Page 18
    user-defined characters. 34 ESC @ [Name] [Format] [Description] Initialize printer ASCII ESC @ Hex 1B 40 Decimal 27 64 Clears the data in ESC J n [Name] [Format] [Range] [Description] Print and feed paper ASCII ESC J n Hex 1B 4A n Decimal 27 74 n 0 ≤n ≤255 Prints the data in
  • Samsung STP-103 | User Manual - Page 19
    ESC R n [Name] [Format] [Range] [Description] Select an international character set ASCII ESC R n Hex 1B 52 n Decimal 27 82 n 0 ≤n ≤10 Selects an international character set n from the following table: n Character set 0 U.S.A. 1 France 2 Germany 3 U.K 4 Denmark Ⅰ 5 Sweden
  • Samsung STP-103 | User Manual - Page 20
    paper feed amount is 40 inches. Even if a paper feed amount of more than 40 inches is set, the printer feeds the paper only 40 inches. ● When label mode is selected and a paper (xL + xH×256)×8 dots in the horizontal direction for the non-volatile bit image you are defining. • yL, yH
  • Samsung STP-103 | User Manual - Page 21
    downloaded bit image using the dots specified by x and y. ● x indicates the number of dots in the horizontal direction. ● y indicates the number of dots in the vertical direction. GS / m [Name] [Format] [Range] [Description] Print downloaded bit image ASCII GS / m Hex 1D 2F m Decimal 29
  • Samsung STP-103 | User Manual - Page 22
    ID ASCII ESC I n Hex 1D 49 n Decimal 29 73 n 1 ≤n ≤3 , 49 ≤n ≤51 Transmits the printer ID specified by n as follows: n Printer ID Specification ID(hexadecimal) 1,49 Printer model ID STP-103S / STP-103P 30 2,50 Type ID 02 3,51 ROM version ID Depends on ROM version 10 GS L nL
  • Samsung STP-103 | User Manual - Page 23
    Not used. Fixed to on Cover is closed Cover is open Paper is not being fed by using the paper feed button Paper is being fed by using the paper feed button Not used. Fixed to off Second byte (printer information) Bit Off/On Hex Decimal 0 - - - 1 - - - 2 - - - 3 Off 00 0 4 Off 00
  • Samsung STP-103 | User Manual - Page 24
    ≤n ≤255 Sets the height of the bar code. n specifies the number of dots in the vertical direction. n = 162 ① GS k m d1...dk NUL ② GS k m n d1...dn [Name] used :] ● The printer prints an HRI character (□) as start character at the beginning of the HRI character string. ● The printer prints an HRI
  • Samsung STP-103 | User Manual - Page 25
    code table. ● When using the CODE128 in this printer, take the following points into account for data transmission that is defined by combining one of the 103 bar code characters and 3 code sets. "{" is defined by transmitting "{" twice consecutively. Specific character SHIFT CODE A CODE B CODE C
  • Samsung STP-103 | User Manual - Page 26
    vertical direction for the STP-103S) PRINTER 20 TXD (O) 19 RXD (I) 21 CTS (I) 22~25 GND 18 RTS (O) FGND 25 PINE MALE CONNECT HOST 2 RXD (I) 3 TXD (O) 7 RTS (O) 5 GND 8 CTS (I) 4 DTR (O) 6 DSR (I) FGND 9 PINE FEMALE Parallel Interface Connector (STP-103P) PRINTER
  • Samsung STP-103 | User Manual - Page 27
    000 line Head 50 million pulse (about 50km) ※ Paper - Paper thickness : 0.06 ~ 0.09mm - Roll size : Ø60 ~ 57 (w) - Roll spool diameter 1) Inside : Ø12mm (0.47") 2) Outside : Ø18mm (0.71") ※Option : STP-103DK 1) Serial Interface Connector Specification PRINTER 19 RXD (I) 20 TXD (O) 18 RTS
  • Samsung STP-103 | User Manual - Page 28
    2) Parallel Interface Connector Specification PRINTER 1 /STROBE (I/O) 2 DATA0 (I/O) 3 DATA1 (I/O) 4 DATA2 (I/O) 5 DATA3 (I/O) 6 DATA4 (I/O) 7 DATA5 (I/O) 8 DATA6 (I/O) 9 DATA7 (I/O) 10 /ACK (I) 11 BUSY (I) 12 PE (I) 13 SLCT 15 /ERROR (I) 22~25 GND FGND HOST 1 /
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
POWER
ERROR
FEED
ON LINE
KN04-00003A
Rev.
2.6
S
TP-103
THERMAL PRINTER
www.samsungminiprinters.com
USER’S MANUAL