Samsung T200 Quick Guide (easy Manual) (ver.1.0) (English)
Samsung T200 Manual
 |
View all Samsung T200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Samsung T200 manual content summary:
- Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 1
LCD MONITOR quick start guide T220,T200,T190,T220G,T200G,T190G ii - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 2
are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Manuals Monitor Quick Setup Guide Cables Warranty Card (Not available in all locations) User's Guide D-Sub Cable Others Power Cord DVI Cable (option) Cleaning Cloth Cable holding ring 9 Stand Body - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 3
The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count. Note The resolution displayed on the screen is the optimal - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 4
not on the screen, push the mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. >> Click here to see an animation clip AUTO button Use this button for auto adjustment. >> Click here to see an animation clip Power button [ ] Use this button for turning the monitor - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 5
at the back of the monitor may vary from product to product. POWER port Connect the power cord for your monitor to the POWER port on the back of the monitor. DVI IN port Connect the DVI Cable to the DVI IN port on the back of your monitor. RGB IN port Connect the D-sub cable to the 15-pin, RGB - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 6
Introduction 2. Connect the Kensington Lock cable. 3. Fix the Kensington Lock to a desk or a heavy stationary object. Note See Connecting Cables for further information regarding cable connections. 13 - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 7
of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 8
Using the Stand Monitor Assembly Connections Folding the base Monitor and Bottom Note You can tilt the monitor upwards at an angle of -1° to 21°. 15 - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 9
monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 10
not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1440 x 900 60 Hz" message comes up, disconnect the cable - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 11
maximum resolution and frequency that the monitor can handle properly. A: If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1440 x 900 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 12
video card manual to see if the Plug & Play (VESA DDC) function can be supported. A: Install the monitor driver according to the Driver Installation Instructions. Check when MagicTune™ does not function properly. Q: MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 13
. Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.) If you installed - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 14
ME/2000: Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Q: How can I clean the outer case/LCD Panel? A: Disconnect the power cord and then clean the monitor with a soft cloth, using - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 15
not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message comes up, disconnect the cable - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 16
on the screen. I cannot turn on the monitor. Q: Is the power cord connected properly? A: Check the power cord connection and supply. Q: Can you see "Check Signal Cable" on the screen? A: (Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 17
mode. A: Press a key on the keyboard to activate the monitor and restore the image on the screen. A: If there is still no image, press the ' /SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen. Q: Connected using the DVI cable - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 18
Troubleshooting LED is blinking but no images on the screen. Q: Is the frequency properly adjusted when checking the Display Timing on the menu? A: Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 19
. Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.) If you installed - Samsung T200 | Quick Guide (easy Manual) (ver.1.0) (English) - Page 20
ME/2000: Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Q: How can I clean the outer case/LCD Panel? A: Disconnect the power cord and then clean the monitor with a soft cloth, using
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
±±
LCD MONITOR
quick start guide
T220,T200,T190,T220G,T200G,T190G