Sanyo PDG-DHT8000L Owners Manual - Page 15

Remote Control Battery Installation, Remote Control Receivers and Operating Range, Wired Remote

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Pull up the lid and remove it. Two AA size batteries For correct polarity (+ and -), be sure battery terminals are in contact with pins in the compartment. To ensure safe operation, please observe the following precautions : ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not drop the remote control. ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared Remote Receivers) when pressing the buttons. Maximum operating range for the remote control is about 16.4' (5 m) and 60 degrees from the front, rear or top of the projector. Infrared Remote Receivers are provided in the front and back and on the top of the projector. You can conveniently use these receivers. (pp.10, 56) 16.4' (5 m) ✔Note: •W hen hanging the projector from the ceiling, select the Infrared Remote Receiver which is located farther away from the fluorescent light. (p.56) •W hen using the projector in the horizontal position without hanging from the ceiling, it is recommended to deactivate the top Infrared Remote Receiver to avoid the effects of the fluorescent light. (p.56) 16.4' (5 m) Wired Remote Control The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside of the operating range (16.4'/ 5 m). Connect the remote control and the projector with the remote control cable (sold separately). Connected with the remote control cable, the remote control does not emit wireless signal. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Remote Control Battery Installation
1
2
3
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
Two AA size batteries
For correct polarity (+ and –),
be sure battery terminals are
in contact with pins in the
compartment.
To ensure safe operation, please observe the following precautions :
l
Use two (2) AA or LR6 type alkaline batteries.
l
Always replace batteries in sets.
l
Do not use a new battery with a used battery.
l
Avoid contact with water or liquid.
l
Do not expose the remote control to moisture or heat.
l
Do not drop the remote control.
l
If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
l
Risk of an explosion if battery is replaced by an incorrect type.
l
Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Point the remote control toward the projector (to
Infrared Remote Receivers) when pressing the buttons.
Maximum operating range for the remote control is
about 16.4’ (5 m) and 60 degrees from the front, rear or
top of the projector.
Infrared Remote Receivers are provided in the front
and back and on the top of the projector. You can
conveniently use these receivers. (pp.10, 56)
16.4’
(5 m)
Remote Control Receivers and Operating Range
The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside
of the operating range (16.4’/ 5 m). Connect the remote control and the projector with the remote control cable (sold
separately). Connected with the remote control cable, the remote control does not emit wireless signal.
Wired Remote Control
Part Names and Functions
16.4’
(5 m)
15
Pull up the lid
and remove it.
✔
Note:
•
When hanging the projector from the ceiling, select the
Infrared Remote Receiver which is located farther away
from the fluorescent light. (p.56)
•
When using the projector in the horizontal position without
hanging from the ceiling, it is recommended to deactivate
the top Infrared Remote Receiver to avoid the effects of
the fluorescent light. (p.56)