Sanyo PDG-DHT8000L Owners Manual - Page 74

The image is Top/Bottom, The image is Left/Right

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Appendix appears on the screen - T he end of lamp life is approaching. Replace the lamp with a new one promptly. (See page 68) - T he filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 64-65) appears on the screen The image is out of focus. - Adjust the focus of the projector. - Check Projection Lens to see if it needs cleaning. ✔Note: M oving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such cases, leave the projector OFF and wait until condensation evaporates. - Projecting from excessive slant angle to the screen may cause keystone distortion and partial imperfect focus. The image is not bright enough. - Check if "Contrast" or "Brightness" are adjusted properly. (See page 46) - Check if "Image level" is selected properly. (See pages 39, 43) - Check the Lamp control function. ( See "SETTING" section on page 50) - Check the Lamp 1/2 replace indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. (See page 68) - The image is darker when 1 lamp mode is selected, compared with 2 lamp mode. Check the lamp mode at SETTING section on page 50. The color is strange. The image is Left/Right reversed. The image is Top/Bottom reversed. The image is distorted or runs off. - Check the Input signal, color system, video system, or computer system mode. - Check the Ceiling / Rear function. (See pages 41, 45) - Check the Ceiling function. (See pages 41, 45) - Check "PC Adjust" menu or " Screen" menu and adjust them. Auto PC adjustment function does not work. - Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p, 720p, 480i, 575i, 1035i, 1080p, or 1080i is selected or when the digital signal is input into DVI terminal. (See page 36) Some displays are not seen during the operation. - Check the Display function (see page 49). The setting does not remain after turning off power. - Make sure you selected "Store" after adjusting settings. Some settings cannot be stored if not registered with "Store". Power management function does not work. Image disappears automatically. Capture function does not work. Some menus cannot be selected. - Power management function cannot work while "Freeze" function is running or the shutter is closed. - Check the power management function in the Setting. The power management is set to "On" at the factory. - Check the connection to see if there is signal. - Each of the Video Input and Computer Input has a limit on selectable menus. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
74
appears on the screen
–
The end of lamp life is approaching. Replace the lamp with a new one promptly.
(See page 68)
appears on the screen
–
The filter is out of scroll. Replace the filter cartridge with a new one promptly.
(See pages 64-65)
The image is out of focus.
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
✔
Note:
Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such cases,
leave the projector OFF and wait until condensation evaporates.
– Projecting from excessive slant angle to the screen may cause keystone distortion and
partial imperfect focus.
The image is not bright
enough.
– Check if “Contrast” or “Brightness” are adjusted properly. (See page 46)
– Check if “Image level” is selected properly. (See pages 39, 43)
– Check the Lamp control function. ( See “SETTING” section on page 50)
– Check the Lamp 1/2 replace indicators. If it lights, the end of lamp life is approaching.
Replace the lamp with a new one promptly. (See page 68)
– The image is darker when 1 lamp mode is selected, compared with 2 lamp mode.
Check the lamp mode at SETTING section on page 50.
The color is strange.
– Check the Input signal, color system, video system, or computer system mode.
The image is Left/Right
reversed.
– Check the Ceiling / Rear function. (See pages 41, 45)
The image is Top/Bottom
reversed.
– Check the Ceiling function. (See pages 41, 45)
The image is distorted or
runs off.
– Check “PC Adjust” menu or “ Screen” menu and adjust them.
Auto PC adjustment
function does not work
.
– Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p,
720p, 480i, 575i, 1035i, 1080p, or 1080i is selected or when the digital signal is input
into DVI terminal. (See page 36)
Some displays are not
seen during the operation.
– Check the Display function (see page 49).
The setting does not
remain after turning off
power.
– Make sure you selected “Store” after adjusting settings. Some settings cannot be
stored if not registered with “Store”
.
Power management
function does not work.
– Power management function cannot work while “Freeze” function is running or the
shutter is closed.
Image disappears
automatically.
– Check the power management function in the Setting. The power management is set
to "On" at the factory.
Capture function does not
work.
– Check the connection to see if there is signal.
Some menus cannot be
selected.
– Each of the Video Input and Computer Input has a limit on selectable menus.
Appendix