Sanyo PDG-DHT8000L Owners Manual Network set up

Sanyo PDG-DHT8000L - 8000 Lumens Manual

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PDG-DHT8000L manual content summary:

  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 2
    installed and used in accordance with the instruction manual, may cause harmful interference to radio user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 3
    Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 4
    instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector and Operation 17 Login the setting page of the projector...18 [1] Enter the IP address...18 [2] Login...18 [3] Display of main setting
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 5
    Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH 
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 6
    PJ1 Intranet PC5 E-Mail Alert function (+p.25) The projector sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector. This message describes how to solve the cause of the problems. You can take efficient action for quick recovery. PC1
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 7
    projector is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), to control and set up the projector. The layout of pages in projector. If you do not use the function E-mail Alert, this application is not required. Network specifications of the projector
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 8
    this manual This manual does not provide the detailed description of basic operation and functions for computer, web browser, projector and network. For instructions is a registered trademark of Sun Microsystems, Inc. DLP and DLP logo are registered trademarks of Texas Instruments. BrilliantColor
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 9
    pp.11-16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projectors, then start browser configurations. ➔ "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 10
    Chapter 1 Preparation 10
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 11
    Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 12
    . When installing, consult your system administrator to set up the LAN appropriately. Connecting to an Ethernet cable To connect your projector to a hub which supports 10Base-T/100Base-TX, use a STP (Shield Twisted Pair) straight-through cable having RJ-45 connectors. 1 Turn off the Mains switch
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 13
    the Menu will disappear, the "Please wait..." message will appear, and switching operation will start. Switching will take a while and the projector's LINK/ACT Lamp will be on or blink, and after completing the operation, the "Please wait..." message will disappear. Switches between on and off with
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 14
    On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 15
    enter the complete number on the column. * To change the number in a column, select "C" and press SELECT steps 3 to 4 for entering all the network address. 6. After finishing, select "Exit" and press to set the Network PIN code if you use the projector via the networks. The Network PIN code can be
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 16
    information Select "Network information" in the Network menu and press SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what will be shown.) Network information Network information screen * The numerical
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 17
    Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 18
    projector [1] Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 19
    Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. 19 ENGLISH
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 20
    3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 21
    Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 22
    Language Switches display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector. SERIAL NO. ..........Indicates the serial number of the projector. Network PIN code....Sets the Network PIN code to login the setting page. (+p.23) 22
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 23
    access from an unauthorized person through the network. Enter a 4-digit number as the Network PIN code onto the text box and click Set button. T he projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. This is
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 24
    following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this menu. The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 25
    can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP server Enter server name or IP address of the SMTP server. (up
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 26
    SMTP server and administrator address Enter the server name or IP address of the SMTP server*1, the port number of the SMTP server and administrator address and click Set button. The administrator address is set to "Reply-To" address of the message sent from the projector. *1 T he SMTP server is
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 27
    contents of alert mail" described on the next page. Option ENGLISH ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 28
    operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information. ● When PJ lamp replacement time is reached: TITLE: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 29
    Place Enter place of the projector (optional) Community name(refer).......Enter community name (read only). Default name is "public". Trap Item Description Community name Enter community name to send "Trap". Default name is "public". Trap address Enter IP address of the SNMP manager computer
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 30
    Set button if you tick or un-tick the check box on a page. ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 31
    Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 32
    Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 33
    standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 34
    menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 35
    System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Control
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 36
    Chapter 4 Controlling the Projector Image adjustment This function is to adjust the projected picture each white balance respectively. (0~ 63) Offset * When Color matching is set to "On" and changing the "Target" value of "Advanced color matching", the color temp. indicates "Adj." Red, Green,
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 37
    Control PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 38
    [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode or the lens functions of the projector. Item Description Screen Switches the screen mode. (Normal, Zoom, True, Natural wide, Full, Custom) Ceiling Sets the image top/bottom and
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 39
    Zoom Adjusts the image zoom in and out. Focus Adjusts the focus of the image. Lens shift Positions to the desired point by pressing the Up/Down/Left/Right buttons. Click Reset by one pressing the +/- or Up/Down/Left/ Right buttons to adjust them quickly. Setting up the projector ENGLISH 39
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 40
    Sets the screen background when no signal input. (Blue, User, Black) Lamp mode.........Switches lamp mode. (2 Lamps mode, Lamp1 mode, Lamp2 mode) Lamp control......Selects lamp control mode. (Normal, Eco1, Eco2) Lamp life control...Selects lamp life control mode (Mode1, Mode2) when the total use
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 41
    Setting up the projector Setting 2 Item Description Logo Sets on or off the logo display on the screen during the startup. (User, Default, OFF) Filter control........Scroll the filter. Click "Roll-up", a confirmation display appears, and then click "OK", the filter will be scrolled. Fan speed
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 42
    , All white, All black, Cross)) Factory default....Sets all of the projector control items to the factory default setting except the following items. User Logo, Logo PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ time, Network PIN code, Network setting * This function is
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 43
    PJ time(h Displays the accumulated use time of the projector. Lamp mode Displays the current "Lamp mode". Lamp control Displays the current "Lamp control". Lamp interval Displays the current "Lamp interval". Lamp status Displays the status of the 2 lamps with an icon. Refer to the table on page
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 44
    the lens type number and it's lens specification. Option control No Displays the option control number for purchasing suitable optional terminal boards. Network Items Description MAC address Displays MAC address of the projector. IP address Displays the IP address of the projector. 44
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 45
    used over a specified use time, replace lamp immediately) Indication of the filter status Icon display/background Status Blue Good condition. Yellow/Gray Red/Gray Filter is almost clogged. Filter is clogged. Replace a filter with new one. * When the projector cannot decode the return from the
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 46
    Chapter 4 Controlling the Projector 46
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 47
    Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 47
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 48
    (PJ01) to the control computer (PC05) via the hub. Hub Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Computer Name
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 49
    Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group: 192.168.200.0 To another
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 50
    available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP be displayed. Type as below to connect the projector. > open 192.168.1.201 10000 [return] *U se the IP address assigned to the
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 51
    appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set on C1D Menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 52
    not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is There are various ways to change your browser preferences depending on the version or applications. Please see the setting instructions on next page for example
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 53
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 54
    Use a proxy server. If you connect the projector to the computer directly with STP crossover cable, this must be unchecked. To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here. 54
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 55
    to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 56
    and then click Proxies: Change Settings .... 3 Select Proxies projector to the computer directly with STP crossover cable, they must be unchecked. To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 57
    projector if the ACT Lamp does not blink orange. 2. Wrong network configuration of the computer. Check the network configuration of the computer. 3. The proxy setting of the web browser is not set correctly (☞ p.52). 4. The computer does not provide TCP/IP use the IP filtering function provided
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 58
    Chapter 5 Appendix Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 59
    Q&A Operation   Q Why can't I change the controls in the setting page with web browser? A Please make sure the projector is turned on. If it is in the standby mode, the setting is not effective to the projector. To control the projector with a web browser, the projector must be in the powered-on
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 60
    are reserved. Rule3 The IP address must correlate to a network number. If network numbers are different between the equipment, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 61
    Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult
  • Sanyo PDG-DHT8000L | Owners Manual Network set up - Page 62
    NETWORK OWNER'S MANUAL SO-KE2AL SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.