Sanyo PDG-DXL2000 Owners Manual Network set up

Sanyo PDG-DXL2000 - 2000 Lumens Manual

Get Sanyo PDG-DXL2000 - 2000 Lumens PDF manuals and user guides
UPC - 086483079436
View all Sanyo PDG-DXL2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PDG-DXL2000 manual content summary:

  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 2
    by turning the equipment off and on, the user is encouraged to try to correct the interference by instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PDG-DXL2000 Trade Name : Sanyo Responsible party : SANYO
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 3
    Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 4
    Table of contents Compliance...2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9 Chapter 2 Setup Procedures 11 Connecting to the LAN line...12
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 5
    Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH 
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 6
    sends mes- sages to the registered e-mail PC1 PC2 addresses when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You can take efficient action for quick recovery. PJ2 PJ1 PC5 Turn ON PJ2
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 7
    512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of colors: Either of 16 or 9.0 Safari 3.1 * Used to control and set up the projector. The layout of pages in the browser may slightly differ from each
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 8
    manual This manual does not provide the detailed description of basic operation and functions for computer, web browser, projector and network. For instructions Other product or brand names in this manual are registered trademarks or trademarks of their respective owners. * Unauthorized use of a part
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 9
    "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to operate the projector. ■ Operate and manage the projector ➔ "4. Controlling the projector" (pp.31-44) ➔ "Power Control and status check" (pp.32-33) ➔ "Control" (pp.34-37) ➔ "PC adjustment
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 10
    Chapter 1 Preparation 10
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 11
    Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 12
    ed but- tons. Then the Menu will disappear, the "Please wait..." message will appear, and switching operation will start. Switching will take a while and the projector's LINK/ACT Lamp will be on or blink, and after completing the operation, the "Please wait..." message will disappear. 12
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 13
    DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 14
    "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 15
    Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 16
    Chapter 2 Setup Procedures Wired LAN factory default settings Parameter LAN 1 SELECTED LAN LAN 2 LAN 3 DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 17
    Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 18
    login Network PIN code onto the Password text area and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 19
    Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 20
    3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. The basic operation and procedures commonly used on this manual are described below. Example of the setting page The setting menu appears when clicking the sub
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 21
    Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 22
    display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector SERIAL NO. ..........Indicates the serial number of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 23
    System Industries Association (JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 24
    in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. * The numerical
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 25
    an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP server Enter server name or IP
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 26
    page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your net- work environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 27
    SMTP server Error information Error message for authentication problem Error information Option selection for sending alert mail PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 28
    once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information. ● When PJ lamp replacement time is reached: TITLE: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 29
    Click SNMP Setting on the main menu and set up each item. PJ information Item Description Contact Enter user name of the projector etc. (optional) Place Enter place of the projector (optional) Community name(refer).......Enter community name (read only). Default name is "public". Trap Item
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 30
    Set button if you tick or un-tick the check box on a page. ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 31
    Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 32
    Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 33
    standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel.  When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 34
    differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 35
    This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu computer system of the input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed. Available system at
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 36
    Chapter 4 Controlling the Projector Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speaker. (0 ~ 63) Mute Suppresses the sound. (ON, OFF) 36
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 37
    Adjusts picture color saturation (0~ 63) Tint Adjusts picture hue (0~ 63) Color temp Sets a color temperature mode. (High, Mid, Low, X Low,, User.) White Balance Red, Green, Blue...... Adjusts each white balance respectively. (0~ 63) * When changing the value of the white balance, the color
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 38
    . This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 which are the customized mode created
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 39
    the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item Description Screen Switches the screen mode. (Normal, Full, Wide(16:9), Zoom
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 40
    emitter system. (0-31) Zoom Sets reset or store the adjustment value with ZOOM+/- buttons on the projector. (Reset, Store1, Store2) Background.........Sets the screen background when no signal input. (Blue, User, Black) Display Switches on or off the on-screen menu display on the screen. (OFF
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 41
    the screen. (OFF, 2000H, 3000H, 4000H) Factory default....Sets all of the projector control items to the factory default setting except the following items. User Logo, Log PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ time * This function is effective for all the Network
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 42
    ) status (Yes, No) PJ time(h Displays the accumulated use time of the projector. Lamp Corres. Value(h).....Displays the use time (Corresponding value) of the lamp. Filter time(h Displays the accumulated use time of the filter. Network Items Description MAC address Displays MAC address of the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 43
    use time, replace lamp immediately) Gray/Blue Gray/Red Lamp off (Normal) Lamp off (Lamp is being used over a specified use time, replace lamp immediately) Red/Blue with X Red/Red with X Lamp failure (Lamp failure, check lamp condition) Lamp failure (Lamp failure and lamp is being used over
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 44
    Chapter 4 Controlling the Projector 44
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 45
    Chapter 5 Appendix Connection examples Use of telnet Web browser setting Q & A 5 ENGLISH 45
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 46
    the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 47
    . Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 48
    *1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. Select Run... submenu from Start menu on the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 49
    appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set on C1D Menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 50
    is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 51
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 52
    server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with STP crossover cable, this must be unchecked
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 53
    to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 54
    and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with STP crossover cable, they must be unchecked
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 55
    of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong function on the login page (☞ p.23). 2. Please use the IP filtering function provided with the gateway (router) to restrict the accessing from the
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 56
    Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 57
    take a lot of time to complete the page display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 58
    , they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.48 - 49). Q What is the MAC address assigned to
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 59
    Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult
  • Sanyo PDG-DXL2000 | Owners Manual Network set up - Page 60
    NETWORK OWNER'S MANUAL SO-KV8AC SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.