Sanyo PLC-HF10000 Owners Manual

Sanyo PLC-HF10000 Manual

Get Sanyo PLC-HF10000 PDF manuals and user guides View all Sanyo PLC-HF10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-HF10000 manual content summary:

  • Sanyo PLC-HF10000 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-HF10000L ✽ Projection lens not included. Owner's Manual
  • Sanyo PLC-HF10000 | Owners Manual - Page 2
    and rear projection, perpendicular omnidirectional projection, variety of lens options, etc. ◆ Simple Computer System Setting The projector has the Multi-scan system to conform to almost all computer output signals quickly (p.35). Supported resolution up to WUXGA. ◆ Security Function The Security
  • Sanyo PLC-HF10000 | Owners Manual - Page 3
    Filter Instructions 71 Replacing the Filter Cartridge 72 Resetting the Filter Counter 73 Resetting the Scroll Counter 73 Lamp Management 74 Lamp Replacement 75 Cleaning the Projection Lens 77 Cleaning the Projector Cabinet 77 Warning Indicators 78 Appendix 79 Troubleshooting 79
  • Sanyo PLC-HF10000 | Owners Manual - Page 4
    again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE
  • Sanyo PLC-HF10000 | Owners Manual - Page 5
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo PLC-HF10000 | Owners Manual - Page 6
    Safety Instructions Air Circulation Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. IMPORTANT! Filter Maintenance!! The projector uses a lamp which generates
  • Sanyo PLC-HF10000 | Owners Manual - Page 7
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in
  • Sanyo PLC-HF10000 | Owners Manual - Page 8
    Safety Instructions Moving the Projector Retract the adjustable feet to prevent damage to lens and cabinet. For safety, holding the projector on both sides by 2 or more people is recommended to move the projector because the projector is heavy. When moving the projector by one person from necessity,
  • Sanyo PLC-HF10000 | Owners Manual - Page 9
    if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of measures. AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power
  • Sanyo PLC-HF10000 | Owners Manual - Page 10
    Functions q Lens Mount Cover o w Projection Lens (Optional) e Indicators r Infrared Remote Receiver (Front) t Adjustable Feet y Terminals and Connectors u Handle i Side Control o Lamp Cover theft of the projector. *Kensington is a registered trademark of ACCO Brands Corporation. 10
  • Sanyo PLC-HF10000 | Owners Manual - Page 11
    series B) USB connector is to used to service the projector. r R/C JACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (not supplied). t LAN PORT Connecting the Ethernet cable See the owner's manual of "Network Set-up and Operation" for
  • Sanyo PLC-HF10000 | Owners Manual - Page 12
    o r t !0 y !1 u !2 q ON/STAND-BY button Turns the projector on or off. (pp.24,25) w SHUTTER button Closes and opens up the button Lights the side control and around terminals. (p.28) o LENS SHIFT button Selects the LENS SHIFT function. (p.28) !0 INPUT button Selects an input source
  • Sanyo PLC-HF10000 | Owners Manual - Page 13
    to be turned on in standby mode. And it flashes green in Power Management mode. (pp.62, 85-87) w LAMP Indicator This indicator is dim when the projector is turned on. And bright when the projector is in stand-by mode. (pp.85-87) e WARNING TEMP. indicator This indicator flashes red when internal
  • Sanyo PLC-HF10000 | Owners Manual - Page 14
    signal is being sent from the remote control unit to the projector. e ON button Turns the projector on. (p.24) r SHUTTER button Closes the built-in 26) -Pan the image in DIGITAL ZOOM +/- mode. (p.44) u LENS SHIFT button Selects the LENS SHIFT function. (p.29) i ZOOM buttons Zoom in and out the images
  • Sanyo PLC-HF10000 | Owners Manual - Page 15
    by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared Remote Receivers) when pressing the buttons. Maximum operating range
  • Sanyo PLC-HF10000 | Owners Manual - Page 16
    controls to prevent remote control interference. Assign the same code the you specified for the projector to the remote control. See "Remote Control" on page 61 for assigning a remote control code to the projector. Follow the procedures below to select the assigned code. Press and hold the MENU and
  • Sanyo PLC-HF10000 | Owners Manual - Page 17
    . - Do not use the optional lens below for this projector. Otherwise damages may result. LENS MODEL NO. : LNS-T01, LNS-T01Z - Lens installation and replacement should be performed by the qualified service personnel. - When setting the projector after lens installation, be sure to replace
  • Sanyo PLC-HF10000 | Owners Manual - Page 18
    rotate the feet clockwise. To lower the projector or to retract the adjustable feet, rotate the feet counterclockwise. To correct keystone distortion, press the KEYSTONE button on the remote control or select Keystone from the menu (see pages 31, 45, 52). When the lens is shifted to rightmost. REAR
  • Sanyo PLC-HF10000 | Owners Manual - Page 19
    Terminal ✔Note: • In the replacement of interface board, turn off the projector, press the Main On/Off Switch to Off and unplug the AC power interface board. 3 Replace the interface board. Insert a new interface board along Guide to fit Socket to inside Plug. 4 Tighten screws to secure the interface
  • Sanyo PLC-HF10000 | Owners Manual - Page 20
    cable • DVI/HDMI cable • USB cable • VGA Cable (D-sub 15 pin) * ( *One cable is supplied; Other cables are not supplied with this projector.) • BNC Cable (BNC x 5) Laptop type Desktop type Monitor Output Monitor Output Monitor Output Serial out USB port DVI-D Cable DVI/HDMI Cable VGA
  • Sanyo PLC-HF10000 | Owners Manual - Page 21
    Video Cable (BNC x 3, BNC x 1) • HDMI Cable • SCART-VGA Cable • DVI-D Cable • S-Video Cable ( Cables are not supplied with the projector.) Video Source (example) Installation Professional Digital VCR Video Disc Player Component video output equipment. (such as DVD player or high-definition
  • Sanyo PLC-HF10000 | Owners Manual - Page 22
    Installation Attaching the Cable Tie You can dress and secure all cables to a cable tie (supplied). The cable tie is reusable and can be loosened and tightened as many times as needed. To loosen the cable tie 2 1 Cable tie 2. Loosen the cable tie in the arrow direction. Tab 1. Pull the tab in the
  • Sanyo PLC-HF10000 | Owners Manual - Page 23
    . If you are not sure of the type of power being supplied, consult your authorized dealer or service center. Connect the projector with all peripheral equipment before turning on the projector. CAUTION The AC outlet must be near this equipment and must be easily accessible. ✔Note: •Unplug the
  • Sanyo PLC-HF10000 | Owners Manual - Page 24
    screen and the countdown starts. 4 After the countdown, the input source that was selected the last time and the Lamp control status icon (see page 74) appear on the screen. If the projector is locked with a PIN code, PIN code input dialog box will appear. ✔Note: • When the Logo select function is
  • Sanyo PLC-HF10000 | Owners Manual - Page 25
    of this manual and keep it on hand. Should the PIN code be missing or forgotten, consult your dealer or service center. Turning Off the Projector 1 Press again to turn off the projector. The LAMP indicator lights bright and the POWER indicator turns off. 3 When the projector has cooled down enough,
  • Sanyo PLC-HF10000 | Owners Manual - Page 26
    Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the on-screen into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. Side Control 1 Press the MENU button on the side control or the remote control to
  • Sanyo PLC-HF10000 | Owners Manual - Page 27
    ., Screen, Lamp mode, Lamp control, Lamp interval, Lamp 1, Lamp 2, Language, Filter counter, Power management, Key lock, PIN code lock, Shutter management, Remote control, SERIAL NO., and Option control No. (p.29). i Network See the owner's manual of "Network Set-up and Operation". o Guide The key
  • Sanyo PLC-HF10000 | Owners Manual - Page 28
    . • The arrows turn red when the lens shift comes to the center position of the screen. Information Information display can be used to confirm the current operating condition of the projector and the signal being projected through the projector. Press the INFORMATION button to toggle between
  • Sanyo PLC-HF10000 | Owners Manual - Page 29
    Press the MENU button to show the main menu. Press the button again to hide the menu. LENS SHIFT button See page 28 for details. SHUTTER button MENU button ZOOM buttons Press the ZOOM buttons on menu list may be different from the actual values. • SERIAL NO. is used to service the projector. 29
  • Sanyo PLC-HF10000 | Owners Manual - Page 30
    Basic Operation LIGHT button Press the LIGHT button to turn on/off Keypad backlight. FREEZE button Press the FREEZE button on the remote control to freeze the picture on the screen. To cancel the FREEZE function, press the FREEZE button again or press any other button. Fig.1 will appear when the
  • Sanyo PLC-HF10000 | Owners Manual - Page 31
    Keystone Correction Press the KEYSTONE button on the remote control to switch the Standard (for Vertical/Horizontal) /Corner correction adjustment. The Standard or Corner correction adjustment dialog box appears. Use the Point ed 7 8 buttons to correct the Standard or Corner distortion. The
  • Sanyo PLC-HF10000 | Owners Manual - Page 32
    Side Control Side Control Input Selection Direct Operation INPUT button The input source changes each time you press the INPUT button on the side control as follows: Input 1→Input 2→ ... Before using the INPUT button on the side control or the remote control, you must select a correct input source
  • Sanyo PLC-HF10000 | Owners Manual - Page 33
    Computer Input Source Selection Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Input and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons to select the desired input and then press the Point 8 button to access the
  • Sanyo PLC-HF10000 | Owners Manual - Page 34
    component signal and the analog RGB signal. When analog RGB signal is not recognized in Y,Pb/Cb,Pr/Cr input source, set to RGB input manually. INPUT 2 MENU 34
  • Sanyo PLC-HF10000 | Owners Manual - Page 35
    to display proper images. If the image is not projected properly, a manual adjustment is required (pp.37, 38). There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on pp.79-81.) PC System Menu Customized Mode (110) set
  • Sanyo PLC-HF10000 | Owners Manual - Page 36
    parameters. The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC System Menu (p.35). See "Manual PC Adjustment" on pages 37, 38. ✔Note: • Fine sync, Total dots, Position H and Position
  • Sanyo PLC-HF10000 | Owners Manual - Page 37
    PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the
  • Sanyo PLC-HF10000 | Owners Manual - Page 38
    selected when 480i, 575i, 480p, 575p, 720p, 1035i , 1080i or 1080p is selected in the PC System Menu (p.35). • When input computer signal to the projector, PC adjust function will become available. Press the MENU button to close this dialog box. 38 Press the SELECT button to store the data.
  • Sanyo PLC-HF10000 | Owners Manual - Page 39
    Point ed buttons to select the desired item and then press the SELECT button. Image select Standard Normal picture level preset on the projector. Real Picture level with improved halftone for graphics. Dynamic For viewing pictures in a bright room. Image 1-10 User preset picture adjustment in the
  • Sanyo PLC-HF10000 | Owners Manual - Page 40
    Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Image adjust and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons to select the desired item and then press the SELECT button to display the adjustment
  • Sanyo PLC-HF10000 | Owners Manual - Page 41
    Computer Input MENU Return to the IMAGE ADJUST Menu. Any settings that have been changed will not be stored. To store the changed settings, be sure to select "LIST" and go to the COLOR MANAGEMENT LIST. COLOR SELECTION MODE Level and phase adjustment palette. Gamma adjustment palette. 4 In the
  • Sanyo PLC-HF10000 | Owners Manual - Page 42
    Computer Input Offset (Red/Green/Blue) Press the Point 7 button to lighten red/green/blue tone of the black level of an image; press the Point 8 button to deepen red/green/blue tone of the black level of an image. Auto picture control Use the Point 7 8 buttons to select the desired Auto picture
  • Sanyo PLC-HF10000 | Owners Manual - Page 43
    on the screen. In this case, the Zoom function is not available. When the original image size is larger than the panel size (2048x1080), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to pan the image. When adjusted, the arrows will turn red. When reached to
  • Sanyo PLC-HF10000 | Owners Manual - Page 44
    Computer Input Custom adj. Adjust the screen scale and position manually with this function. Press the Point 8 button or the SELECT button at Custom adj. and Custom adj. is displayed on the screen, you can use
  • Sanyo PLC-HF10000 | Owners Manual - Page 45
    is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear
  • Sanyo PLC-HF10000 | Owners Manual - Page 46
    , and adjusts itself to optimize its performance. When the Video System is 1035i, 1080i or 1080p, select the system manually. Y, Pb/Cb, Pr/Cr SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p
  • Sanyo PLC-HF10000 | Owners Manual - Page 47
    button. 2 Use the Point ed buttons to select the desired item and then press the SELECT button. Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. Dynamic For viewing pictures in a bright room. Image 1-10 User preset picture adjustment in the Image
  • Sanyo PLC-HF10000 | Owners Manual - Page 48
    Video Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Image adjust and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons select the desired item and then press the SELECT button to display the adjustment dialog
  • Sanyo PLC-HF10000 | Owners Manual - Page 49
    Offset (Red/Green/Blue) Press the Point 7 button to lighten red/green/blue tone of the black level of an image; press the Point 8 button to deepen red/green/blue tone of the black level of an image (from 0 to 63). ✔Note • When White balance Red, Green or Blue is adjusted, the Color temp. level will
  • Sanyo PLC-HF10000 | Owners Manual - Page 50
    scan mode. Off.......... Progressive scan mode is Off. On.......... Progressive scan mode is On. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT button
  • Sanyo PLC-HF10000 | Owners Manual - Page 51
    of images naturally without changing the center areas. Custom Provides the last stored aspect screen image. Custom adj. Adjusts the screen scale and position manually with this function. Press the Point 8 button at Custom adj. and the Custom adjustment menu is displayed on the screen, you can use
  • Sanyo PLC-HF10000 | Owners Manual - Page 52
    is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Ceiling Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from
  • Sanyo PLC-HF10000 | Owners Manual - Page 53
    in this option. Countdown Off..... Shows the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Hides the On-Screen Displays, but there are exceptions: • On-Screen
  • Sanyo PLC-HF10000 | Owners Manual - Page 54
    . Eco 2 . . . . Lowers brightness and increase of fan speed. Lower brightness reduces the lamp power consumption and extends the lamp life. It is recommended to use Eco 2 when using the projector continuously over a long period of time. The fan noise becomes louder in Eco 2 than in Eco 1. Select
  • Sanyo PLC-HF10000 | Owners Manual - Page 55
    icon will be displayed at the time of power-on. Then the projector will turn off after 3 minutes. Lamp interval In 1-lamp mode, this function allows you to specify the timing of switching between the lamps. Off Turns off the lamp switching function XXXXH When the cumulated lighting time of the
  • Sanyo PLC-HF10000 | Owners Manual - Page 56
    Settings Mode P in P: Provide the images of Main picture and Sub picture at the ratio of Screen aspect in the Screen Menu. P by P: Provide the images of Main picture and Sub picture at the ratio of 4:3. Main picture / Sub picture Input......Select an input from Input 1-4. Source...Select an input
  • Sanyo PLC-HF10000 | Owners Manual - Page 57
    Color matching When displaying multiple screens, eliminates the difference in color between the images that are projected from the projectors. When multiple sets are used simultaneously, this projector allows the user to correct the difference of colors among the sets. Use the Point ed buttons to
  • Sanyo PLC-HF10000 | Owners Manual - Page 58
    Settings Advanced color matching Select Advanced color matching and press the SELECT button for more detailed settings. Another setting screen will appear. Reset Select Reset and press the SELECT button. Then the confirmation message appears. Press the SELECT button at Yes to reset to the
  • Sanyo PLC-HF10000 | Owners Manual - Page 59
    equipment to equipment. For details, refer to the manual of video equipment. Logo (Logo and Logo be displayed the next time you turn on the projector. To cancel the capture function, select Yes in The output image resolution from a computer can be supported up to the panel resolution (2048 x 1080).
  • Sanyo PLC-HF10000 | Owners Manual - Page 60
    Settings Use the Point ed buttons on the side control or Number buttons on the remote control to enter a number. Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. Off The screen logo can be changed freely from the Logo Menu (p.59). On The screen logo
  • Sanyo PLC-HF10000 | Owners Manual - Page 61
    Codes" on page 16. ✔Note • When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector. • If the batteries are removed from the remote control for a long period
  • Sanyo PLC-HF10000 | Owners Manual - Page 62
    life, the Power management function turns off the projection lamp when the projector is not operated for a 4 : 50 certain period. Select one of the following options: Timer left before Lamp is off. Ready When the lamp has been fully cooled down, the POWER indicator changes to green blinking
  • Sanyo PLC-HF10000 | Owners Manual - Page 63
    control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off
  • Sanyo PLC-HF10000 | Owners Manual - Page 64
    " and the number will turn red for a moment. Enter the correct PIN code all over again. When the projector is locked with a PIN code, the PIN code lock symbol appears in the Guide. To change the PIN code lock setting Use the Point ed buttons to select OFF, On 1 or On 2. Press
  • Sanyo PLC-HF10000 | Owners Manual - Page 65
    when the shutter is closed; - INPUT button and INPUT 1/2/3/4 button - ON/STAND-BY button Management The Shutter Management function turns off the projection lamp when the projector is left with the shutter closed and the set time has passed away. The count-down time can be set between 5 and 480
  • Sanyo PLC-HF10000 | Owners Manual - Page 66
    Settings Video delay control When you want to make a digital processing of a projected image faster, set this function. Use the Point ed buttons, select an item of Off/Low/Mid/ High. Digital processing speed becomes fast by order of Low → Mid → High. High is the fastest. ✔Note: • The following
  • Sanyo PLC-HF10000 | Owners Manual - Page 67
    and the total accumulated time turns red, indicating that the filter replacement is necessary. If the filter is out of scroll and the projector reaches a time set in the timer setting, Fig.2 appears on the screen, indicating that the filter cartridge replacement is necessary. Filter counter reset
  • Sanyo PLC-HF10000 | Owners Manual - Page 68
    P-timer, press and hold the P-TIMER button for a few seconds. Test pattern Various test pattern are available for use when setting up the projector. Factory default This function returns all setting values except for User logo, PIN code lock, Logo PIN code lock, Filter counter and Network setting
  • Sanyo PLC-HF10000 | Owners Manual - Page 69
    lamp mode. These settings must match those for the rest of the projectors. Select Constant mode from the Lamp mode menu and then specify the same Target value as the projectors , and then overlap the shaded areas by using the lens shift function. When the shaded areas are overlapped with each other
  • Sanyo PLC-HF10000 | Owners Manual - Page 70
    in the same way as Mesured-Red. 9. Adjust the values of Target again. 10. Select Store to complete. (Apply the same adjustment to the other projector if necessary.) Fig.1 70
  • Sanyo PLC-HF10000 | Owners Manual - Page 71
    the filter, but there is no problem for the use of the projector. •Do not use the filter cartridge with other projector. The filter counter and the . If you replace the filter cartridge when the projection lamps are turned on, the projector will be shut down automatically for safety purposes. •Do
  • Sanyo PLC-HF10000 | Owners Manual - Page 72
    using the projector under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements inside the projector. Such ● Model No. of your projector PLC-HF10000L ● Replacement Filter Cartridge Type No. : POA-FIL-180 (Service Parts Code: 610 335 9830
  • Sanyo PLC-HF10000 | Owners Manual - Page 73
    Resetting the Filter Counter Be sure to reset the Filter counter after replacing the filter cartridge. 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Setting and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons to select Filter
  • Sanyo PLC-HF10000 | Owners Manual - Page 74
    changes the lighting lamp (Lamp Mode) by detecting the status of lamp. When either of the 2 lamps is out, the projector operates with 1 lamp. The Lamp Mode can be switched to 2 lamps or 1 lamp manually. Refer to the SETTING section on pages 54, 55. 2 LAMPS MODE 1 LAMP MODE When Lamp 1 is burnt
  • Sanyo PLC-HF10000 | Owners Manual - Page 75
    new one promptly. The timing when the LAMP 1/2 REPLACE indicators should light is depending on the lamp mode. Indicators WARNING: TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER. Lamp replacement icon LAMP 1 / 2 REPLACE indicators Allow the projector to cool, for at least 45 minutes before
  • Sanyo PLC-HF10000 | Owners Manual - Page 76
    information to the dealer. ● Model No. of your projector : PLC-HF10000L ● Replacement Lamp Type No. : POA-LMP146 (Service Parts No. 610 351 5939) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may
  • Sanyo PLC-HF10000 | Owners Manual - Page 77
    harsh chemicals might scratch the surface of the lens. Cleaning the Projector Cabinet Turn off the projector, press the Main On/Off Switch to Off AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal
  • Sanyo PLC-HF10000 | Owners Manual - Page 78
    are still lighting and blinking, unplug the AC power cord and contact the service center. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Indicators LAMP indicator lights on and other indicators blink. 78
  • Sanyo PLC-HF10000 | Owners Manual - Page 79
    Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. 1. Make sure you have properly connected the projector monitor output when connected to the projector. See your computer's instruction manual for the setting. - It takes about 20 seconds
  • Sanyo PLC-HF10000 | Owners Manual - Page 80
    is approaching. Replace the lamp with a new one promptly. (See page 75) appears on the screen The image is out of focus. - The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 71-73) - Adjust the focus of the projector. - Check Projection Lens to see if it
  • Sanyo PLC-HF10000 | Owners Manual - Page 81
    or the service center. - C heck the lamp status and replace the lamp, or decrease Target value in Constant mode. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the
  • Sanyo PLC-HF10000 | Owners Manual - Page 82
    mode Lamp control Lamp interval Lamp 1 Lamp 2 Language Filter counter Power management Key lock PIN code lock Shutter management Remote control SERIAL NO. Option control No. Remote control Projector Effect Release key Standard Real Dynamic Image 1 - Image 10 Auto PC adj. Fine sync. Total dots
  • Sanyo PLC-HF10000 | Owners Manual - Page 83
    Appendix HDMI Input/Video Input Image adjust Contrast Brightness Color Tint Color management Color temp. Red Green Blue Offset Auto picture control Advanced color Sharpness Gamma Noise reduction Progressive Reset Store Video Input System (2) System (3) Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL
  • Sanyo PLC-HF10000 | Owners Manual - Page 84
    Off Blue User Black 2-Lamps 1-Lamp Constant mode Lamp control Normal Double Target Current Auto Normal Eco1 Eco2 Lamp life control Mode1 Mode 2 counter Timer Filter counter reset Scroll remaining Scroll counter reset Remote control/Projector Off/L1/L2 Any/SHUTTER 5-480 Off/CC1/CC2/CC3/CC4 Color
  • Sanyo PLC-HF10000 | Owners Manual - Page 85
    Condition Check the indicators for the projector condition. The projector is operating normally. POWER green LAMP red Indicators WARNING WARNING TEMP. FILTER SHUTTER LAMP 1/2 REP. red orange blue orange Projector Condition The projector is off. (The main On/Off switch is OFF position
  • Sanyo PLC-HF10000 | Owners Manual - Page 86
    to be turned on with the ON/ STAND-BY button.) ✽ ✽ ✽ When either of the 2 lamps is out, the projector operates with 1 lamp. ✽ ✽ ✽ ✽ ✽ The lamp has been used overtime. Replace the lamp immediately. WARNING FILTER When the filter detects clogging, reaches a time set in the timer setting or
  • Sanyo PLC-HF10000 | Owners Manual - Page 87
    TEMP. red WARNING FILTER orange SHUTTER blue LAMP 1/2 REP. orange Projector Condition ✽ ✽ Fig.2 Filter replacement icon to turn on the projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center. Do not leave the projector on. It may
  • Sanyo PLC-HF10000 | Owners Manual - Page 88
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below and less than 230 MHz of Dot Clock. ON-SCREEN RESOLUTION DISPLAY
  • Sanyo PLC-HF10000 | Owners Manual - Page 89
    of your PC may not be projected correctly. In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. Be sure to follow this procedure, otherwise an image may not be projected on the
  • Sanyo PLC-HF10000 | Owners Manual - Page 90
    Appendix Supported Signal Format for Optional Board When using the optional board (DVI) "POA-AMD23ADI", refer to the chart on the previous page. When using other optional
  • Sanyo PLC-HF10000 | Owners Manual - Page 91
    Projector Type Multi-media Projector Information Projection Lamp 380 W NSHA lamp x 2 Lens Attachments (1 type) (For optional lens) q Light Block Plates (3 types) (For optional lens) q Spacer (For optional lens) q Strap (For lens mount cover) q Owner's Manual (CD-ROM) q Quick Reference Guide
  • Sanyo PLC-HF10000 | Owners Manual - Page 92
    Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input INPUT 1 RGB (PC analog) RGB (Scart) RGB (PC Digital) RGB (AV
  • Sanyo PLC-HF10000 | Owners Manual - Page 93
    Configurations of Terminals ANALOG TERMINAL(Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 9 +5V Power 2 Green Input 10 Ground (Vert. sync) 3 Blue Input 11 Ground 4 - - - 12 DDC data 5 Ground (Horiz. sync.) 13 Horiz. sync. 6 Ground (Red) 14 Vert. sync. 7
  • Sanyo PLC-HF10000 | Owners Manual - Page 94
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. PIN Code Lock No. Logo PIN Code Lock No. Factory default set No: 1 2 3 4* Factory default set
  • Sanyo PLC-HF10000 | Owners Manual - Page 95
    Dimensions Unit: inch (mm) 20.87(530) 21.20(538.5) 4.74(120.5) 5.81(147.5) 9.63(244.5) 10.55(268.0) Appendix Screw Holes for Ceiling Mount Screw: M8 Depth: 0.393 (10.0) 8.66(220) 8.46(215) 1.18(30) 5.00(127) 3.03(77) 10.43(265) 6.89(175) 8.27(210) 7.28(185) 23.62(600) 26.77(680) 29.80(757
  • Sanyo PLC-HF10000 | Owners Manual - Page 96
    Appendix List of Picture in Picture On-Board Input1 Input2 Optional Interface Board Dsub -DVI Component -S-video Dual SDI Link SDI Digital Digital Video/ S-video Component Analog PC Digital Scart Analog PC Video/ S-Video Component Analog PC Digital Scart Analog PC Analog PC o o o o o o o
  • Sanyo PLC-HF10000 | Owners Manual - Page 97
    C05 C06 C07 C08 C0D C0E C0F C10 C1C C1D C3A Function Turn the projector ON Turn the projector OFF (immediately OFF) Select Input 1 Select Input 2 Select Input 3 Select UP Focus DOWN Focus UP Lens shift UP Lens shift DOWN Lens shift LEFT Lens shift RIGHT Auto PC Adj. Keystone UP Keystone DOWN
  • Sanyo PLC-HF10000 | Owners Manual - Page 98
    anomaly Cooling down at Power Management mode Power Management mode after Cooling down Cooling down after the projector is turned off when the lamps are out. Stand-by mode after Cooling down when the lamps are out. Stand-by mode after Cooling down at the temperature anomaly. Cooling down when the
  • Sanyo PLC-HF10000 | Owners Manual - Page 99
    KG2A SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Multimedia Projector
MODEL
PLC-HF10000L
Owner’s Manual
✽
Projection lens not included.