Sanyo PLC-HF10000 Network Setup

Sanyo PLC-HF10000 Manual

Get Sanyo PLC-HF10000 PDF manuals and user guides View all Sanyo PLC-HF10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-HF10000 manual content summary:

  • Sanyo PLC-HF10000 | Network Setup - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PLC-HF10000 | Network Setup - Page 2
    . This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
  • Sanyo PLC-HF10000 | Network Setup - Page 3
    Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a
  • Sanyo PLC-HF10000 | Network Setup - Page 4
    instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector ...36 PC adjustment...37 Setting up the projector...38 Screen setting ...38 Lens adjustment...39 Setting 1...40 Setting 2...41
  • Sanyo PLC-HF10000 | Network Setup - Page 5
    Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH 
  • Sanyo PLC-HF10000 | Network Setup - Page 6
    on PJ1 Internet Intranet E-Mail Alert function (+p.25) The projector sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector. This message describes how to solve the cause of the problems. You can take efficient action for quick recovery
  • Sanyo PLC-HF10000 | Network Setup - Page 7
    7 Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x or 9.0 Safari 3.1 * Used to control and set up the projector. The layout of pages in the browser may slightly differ from each type
  • Sanyo PLC-HF10000 | Network Setup - Page 8
    actual operation depending on your computer environment. Use of this manual This manual does not provide the detailed description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer
  • Sanyo PLC-HF10000 | Network Setup - Page 9
    pp.11-16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projectors, then start browser configurations. ➔ "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to
  • Sanyo PLC-HF10000 | Network Setup - Page 10
    Chapter 1 Preparation 10
  • Sanyo PLC-HF10000 | Network Setup - Page 11
    Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11
  • Sanyo PLC-HF10000 | Network Setup - Page 12
    press SELECT button. Then the Menu will disappear, the "Please wait..." message will appear, and switching operation will start. Switching will take a while and the projector's LINK/ACT Lamp will be on or blink, and after completing the operation, the "Please wait..." message will disappear. 12
  • Sanyo PLC-HF10000 | Network Setup - Page 13
    DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP
  • Sanyo PLC-HF10000 | Network Setup - Page 14
    "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what
  • Sanyo PLC-HF10000 | Network Setup - Page 15
    Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All
  • Sanyo PLC-HF10000 | Network Setup - Page 16
    Chapter 2 Setup Procedures 16
  • Sanyo PLC-HF10000 | Network Setup - Page 17
    Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17
  • Sanyo PLC-HF10000 | Network Setup - Page 18
    Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be
  • Sanyo PLC-HF10000 | Network Setup - Page 19
    Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. 19 ENGLISH
  • Sanyo PLC-HF10000 | Network Setup - Page 20
    3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab
  • Sanyo PLC-HF10000 | Network Setup - Page 21
    Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21
  • Sanyo PLC-HF10000 | Network Setup - Page 22
    display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector SERIAL NO. ..........Indicates the serial number of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) Temperature.......Switches
  • Sanyo PLC-HF10000 | Network Setup - Page 23
    System Industries Association (JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class
  • Sanyo PLC-HF10000 | Network Setup - Page 24
    in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. * The numerical
  • Sanyo PLC-HF10000 | Network Setup - Page 25
    an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu Enter e-mail address of the user to send mail when the projector has an abnormality. SMTP Authentication setting Auth Sets authentication setting option
  • Sanyo PLC-HF10000 | Network Setup - Page 26
    setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter
  • Sanyo PLC-HF10000 | Network Setup - Page 27
    missing SMTP server Error information Error message for authentication problem Error information 5 O ption selection for sending alert PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is
  • Sanyo PLC-HF10000 | Network Setup - Page 28
    verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information. ● When PJ lamp replacement time is reached: *The projector lamp 1 has reached replacement time. Lamp 1 ON 2000 h Lamp 2 ON 1800 h ✐ Replace it
  • Sanyo PLC-HF10000 | Network Setup - Page 29
    SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item
  • Sanyo PLC-HF10000 | Network Setup - Page 30
    button if you tick or un-tick the check box on a page. ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into
  • Sanyo PLC-HF10000 | Network Setup - Page 31
    Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31
  • Sanyo PLC-HF10000 | Network Setup - Page 32
    Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. PJ
  • Sanyo PLC-HF10000 | Network Setup - Page 33
    standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. ENGLISH When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To
  • Sanyo PLC-HF10000 | Network Setup - Page 34
    differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the
  • Sanyo PLC-HF10000 | Network Setup - Page 35
    System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Control
  • Sanyo PLC-HF10000 | Network Setup - Page 36
    Chapter 4 Controlling the Projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and
  • Sanyo PLC-HF10000 | Network Setup - Page 37
    PC adjustment PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc.
  • Sanyo PLC-HF10000 | Network Setup - Page 38
    Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode or the lens functions of the projector. Item Description Screen Switches the screen mode. (Normal, Full, Wide(16:9), Zoom, True, Natural wide, Custom) Ceiling Sets the image top
  • Sanyo PLC-HF10000 | Network Setup - Page 39
    Screen aspect, Keystone and Digital zoom. Setting up the projector Lens adjustment Item Description Zoom Adjusts the image zoom in and out. Focus Adjusts the focus of the image. Lens shift Positions to the desired point by pressing the Up/Down/Left/
  • Sanyo PLC-HF10000 | Network Setup - Page 40
    1 Item Description Language Sets the language display of projector's on-screen display menu. Display Switches on or , Black) Lamp mode.........Switches the lamp mode. {2-Lamps mode, 1-Lamp mode (Auto, Lamp1, Lamp2), Constant mode} * Auto ...... A utomatically selects a lamp with shorter
  • Sanyo PLC-HF10000 | Network Setup - Page 41
    - User5] from the pulldown menu. Mode Free Clear the adjustment values. Select a mode no. [User1 - User5] from the pull-down menu. Setting up the projector * Step(s Sets the effective steps (1-20 steps) by one pressing the +/- or Up/Down/Left/Right buttons to adjust them quickly. ENGLISH 41
  • Sanyo PLC-HF10000 | Network Setup - Page 42
    when the AC cord is connected to the outlet. Key lock Sets the prohibition of controls either Projector or Remote control. (OFF, Projector, Remote control) PJ lock suspend...When the projector has a security of PIN code lock, disable this function temporarily by pressing Execute button. Setting
  • Sanyo PLC-HF10000 | Network Setup - Page 43
    - Gradation4, All white, All black, Cross) Factory default....Sets all of the projector control items to the factory default setting except the following items. User Logo, Logo PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ time, Network PIN code, Network setting * This
  • Sanyo PLC-HF10000 | Network Setup - Page 44
    PJ time(h Displays the accumulated use time of the projector. Lamp mode Displays the current "Lamp mode". Lamp control Displays the current "Lamp control". Lamp interval Displays the current "Lamp interval". Lamp status Displays the status of the 2 lamps with an icon. Refer to the table on page
  • Sanyo PLC-HF10000 | Network Setup - Page 45
    page. Option control No Displays the option control number for purchasing suitable optional terminal boards. Network Items Description MAC address Displays MAC address of the projector. IP address Displays the IP address of the
  • Sanyo PLC-HF10000 | Network Setup - Page 46
    Chapter 4 Controlling the Projector Indication of the lamp status Icon display/background Status White/Blue Lamp on (Normal) White/Red Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Gray/Blue Gray/Red Lamp off (Normal) Lamp off (Lamp is being used over a
  • Sanyo PLC-HF10000 | Network Setup - Page 47
    Chapter 5 Appendix Connection examples Use of telnet Web browser setting Q & A 5 ENGLISH 47
  • Sanyo PLC-HF10000 | Network Setup - Page 48
    PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Connecting the projector (PJ01) to the control computer (PC05) via the hub. Hub Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer
  • Sanyo PLC-HF10000 | Network Setup - Page 49
    gateway. Theater Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group
  • Sanyo PLC-HF10000 | Network Setup - Page 50
    *1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the
  • Sanyo PLC-HF10000 | Network Setup - Page 51
    on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set display on C1D Menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a
  • Sanyo PLC-HF10000 | Network Setup - Page 52
    is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is
  • Sanyo PLC-HF10000 | Network Setup - Page 53
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PLC-HF10000 | Network Setup - Page 54
    proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked
  • Sanyo PLC-HF10000 | Network Setup - Page 55
    to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your
  • Sanyo PLC-HF10000 | Network Setup - Page 56
    address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked
  • Sanyo PLC-HF10000 | Network Setup - Page 57
    network. Check LED indicators status (☞ p.12). - Check the connection of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong network configuration of the computer. Check the network configuration of
  • Sanyo PLC-HF10000 | Network Setup - Page 58
    Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP
  • Sanyo PLC-HF10000 | Network Setup - Page 59
    take a lot of time to complete the page display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator
  • Sanyo PLC-HF10000 | Network Setup - Page 60
    , they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.50 - 51). Q What is the MAC address assigned to
  • Sanyo PLC-HF10000 | Network Setup - Page 61
    Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult
  • Sanyo PLC-HF10000 | Network Setup - Page 62
    NETWORK OWNER'S MANUAL SO-KG2A SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.