Sanyo PLC-HF15000L Owner's Manual

Sanyo PLC-HF15000L - 15000 Lumens Manual

Get Sanyo PLC-HF15000L - 15000 Lumens PDF manuals and user guides View all Sanyo PLC-HF15000L manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-HF15000L manual content summary:

  • Sanyo PLC-HF15000L | Owner's Manual - Page 1
    Multimedia Projector MODEL PLC-HF15000L ✽ Projection lens not included. Owner's Manual
  • Sanyo PLC-HF15000L | Owner's Manual - Page 2
    , Portuguese, Dutch, Swedish, Russian, Chinese, Korean, and Japanese (p.54). ◆ Hot-Swap Lamps Hot-swap lamps enable you to replace the failed lamp with a new one without turning off the projector. ◆ Motor-driven Lens Shift Projection lens can be moved up, down, right and left with the motor-driven
  • Sanyo PLC-HF15000L | Owner's Manual - Page 3
    the Filter Counter 74 Lamp Management 75 Lamp Replacement 76 Cleaning the Projection Lens 78 Cleaning the Projector Cabinet 78 Warning Indicators 79 Appendix 80 Troubleshooting 80 Menu Tree 83 Indicators and Projector Condition 86 Compatible Computer Specifications 89 Supported
  • Sanyo PLC-HF15000L | Owner's Manual - Page 4
    of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT
  • Sanyo PLC-HF15000L | Owner's Manual - Page 5
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions
  • Sanyo PLC-HF15000L | Owner's Manual - Page 6
    Safety Instructions Air Circulation Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. IMPORTANT! Filter Maintenance!! The projector uses a lamp which generates
  • Sanyo PLC-HF15000L | Owner's Manual - Page 7
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in
  • Sanyo PLC-HF15000L | Owner's Manual - Page 8
    Safety Instructions Moving the Projector Retract the adjustable feet to prevent damage to lens and cabinet. For safety, holding the carrying handles on both sides by 2 or more people is recommended to move the projector because the projector is heavy. Moving it improperly may result in damage of
  • Sanyo PLC-HF15000L | Owner's Manual - Page 9
    with the instruction manual, may cause projector meets the requirement for use in the country you purchased it. AC Power Cord for the United States and Canada: AC Power Cord used in the United States and Canada from the Parts Department indicated in your User Instructions. If the plug supplied is not
  • Sanyo PLC-HF15000L | Owner's Manual - Page 10
    Kensington* Security Slot This slot is for a Kensington lock used to deter theft of the projector. *Kensington is a registered trademark of ACCO Brands Corporation. o Exhaust Vents !0 Lamp Covers !1 Power Cord Connector !2 Main On/Off Switch !3 Infrared Remote Receiver (Rear) !1 !2 !3 Bottom !5 10
  • Sanyo PLC-HF15000L | Owner's Manual - Page 11
    service the projector. r R/C JACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (not supplied). t LAN PORT Connecting the Ethernet cable See the owner's manual (p.20). HD (HDCP Compatible) signal can be also connected (p.21). 11
  • Sanyo PLC-HF15000L | Owner's Manual - Page 12
    o r t !0 y !1 u !2 q ON/STAND-BY button Turns the projector on or off. (pp.24,25) w SHUTTER button Closes and opens up the LIGHT button Lights the side control and terminals. (p.28) o LENS SHIFT button Selects the LENS SHIFT function. (p.28) !0 INPUT button Selects an input source Input
  • Sanyo PLC-HF15000L | Owner's Manual - Page 13
    . (pp.63, 86-88) w LAMP Indicator This indicator is dim when the projector is turned on. And bright when the projector is in stand-by mode. (pp.86 projector temperature is too high. (pp.79, 86-88) r WARNING FILTER indicator - Lights orange when the clogging of the filter is detected or the filter
  • Sanyo PLC-HF15000L | Owner's Manual - Page 14
    remote control unit to the projector. e ON button Turns the projector on. (p.24) r DIGITAL ZOOM +/- mode. (p.45) u LENS SHIFT button Selects the LENS SHIFT function. (p.29) i ZOOM buttons the input source information. (p.29) !4 FILTER button To schedule a filter cleaning task. (p.31) !5 SCREEN button
  • Sanyo PLC-HF15000L | Owner's Manual - Page 15
    by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared Remote Receivers). The operating distance and angle between the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 16
    controls to prevent remote control interference. Assign the same code the you specified for the projector to the remote control. See "Remote Control" on page 62 for assigning a remote control code to the projector. Follow the procedures below to select the assigned code. Press and hold the MENU and
  • Sanyo PLC-HF15000L | Owner's Manual - Page 17
    used and prepare a suitable lens. For the specifications of Projection Lens, contact sales dealer where you purchased the projector. - Lens installation and replacement should be performed by the qualified service personnel. - When setting the projector after lens installation, be sure to replace
  • Sanyo PLC-HF15000L | Owner's Manual - Page 18
    . This function makes the positioning of images easy on the screen. The amount of lens shift range varies depending on the lens. The shift ranges shown below apply to the LNS-S03 lens. (See page 28) When the lens is shifted to top The display position can be shifted upward up to 50% elevation
  • Sanyo PLC-HF15000L | Owner's Manual - Page 19
    Terminal ✔Note: • In the replacement of interface board, turn off the projector, press the Main On/Off Switch to Off and unplug the AC power cord board. 3 Replace the interface board. Insert a new interface board along Guide to fit Socket to inside Plug. 4 Tighten screws to secure the interface
  • Sanyo PLC-HF15000L | Owner's Manual - Page 20
    cable • DVI/HDMI cable • USB cable • VGA Cable (D-sub 15 pin) * ( *One cable is supplied; Other cables are not supplied with this projector.) • BNC Cable (BNC x 5) Laptop type Monitor Output Monitor Output Desktop type Monitor Output Serial out USB port DVI-D Cable DVI/HDMI Cable VGA
  • Sanyo PLC-HF15000L | Owner's Manual - Page 21
    • Video Cable (BNC x 3, BNC x 1) • HDMI Cable • SCART-VGA Cable • DVI-D Cable • S-Video Cable ( Cables are not supplied with the projector.) Video Source (example) Installation Professional Digital VCR Digital Output HDMI (HDCP compatible) Output Video Disc Player Component video output
  • Sanyo PLC-HF15000L | Owner's Manual - Page 22
    Installation Attaching the Cable Tie You can dress and secure all cables to a cable tie (supplied). The cable tie is reusable and can be loosened and tightened as many times as needed. Cable tie holders To loosen the cable tie 2 1 Cable tie 2. Loosen the cable tie in the arrow direction. Tab 1.
  • Sanyo PLC-HF15000L | Owner's Manual - Page 23
    consult your authorized dealer or service center. 1 Connect the projector with all peripheral equipment before turning on the projector. A power cord clamp outlet, contact your sales dealer. Projector side For the U.S.A. and Canada Ground AC Outlet side For Continental Europe For the U.K.
  • Sanyo PLC-HF15000L | Owner's Manual - Page 24
    be automatically shut down in 3 minutes after turning on to protect the projector. (p.68) • When the Picture in Picture function is set to Mode(1-5), Mode(1-5), Input source, Lamp control status, Lamp replacement icon and Filter warning icon will appear on the screen for 10 seconds. PIN Code Input
  • Sanyo PLC-HF15000L | Owner's Manual - Page 25
    this manual and keep it on hand. Should the PIN code be missing or forgotten, consult your dealer or service center. Turning Off the Projector 1 Press again to turn off the projector. The LAMP indicator lights bright and the POWER indicator turns off. 3 When the projector has cooled down enough,
  • Sanyo PLC-HF15000L | Owner's Manual - Page 26
    Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the on-screen into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. Side Control 1 Press the MENU button on the side control or the remote control to
  • Sanyo PLC-HF15000L | Owner's Manual - Page 27
    , Lamp mode, Lamp control, Lamp interval, Lamp 1, Lamp 2, Lamp 3, Lamp 4, Language, Filter counter, Power management, Key lock, PIN code lock, Shutter management, Remote control, SERIAL NO. and Option control No. (p.30). i Network See the owner's manual of "Network Set-up and Operation". o Guide The
  • Sanyo PLC-HF15000L | Owner's Manual - Page 28
    . • The arrows turn red when the lens shift comes to the center position of the screen. Information Information display can be used to confirm the current operating condition of the projector and the signal being projected through the projector. Press the INFORMATION button to toggle between
  • Sanyo PLC-HF15000L | Owner's Manual - Page 29
    to show the main menu. Press the button again to hide the menu. LENS SHIFT button See page 28 for details. ZOOM buttons Press the ZOOM buttons zoom in and out the image. Remote Control SHUTTER button MENU button LENS SHIFT button ZOOM buttons SCREEN button AUTO PC button IMAGE ADJUST button FOCUS
  • Sanyo PLC-HF15000L | Owner's Manual - Page 30
    INFO. button Press the INFO. button to confirm the current settings of the projector and the signals being transmitted to the projector. Use the Point 7 8 buttons or INFO. button to toggle back and menu list may be different from the actual values. • SERIAL NO. is used to service the projector. 30
  • Sanyo PLC-HF15000L | Owner's Manual - Page 31
    cleaning task. Remote Control LIGHT button FREEZE button P-TIMER button FILTER button IMAGE SEL. button KEYSTONE button PIP button ✔Note See the previous page for the description of other buttons. User 1 of PIP (example) IMAGE SEL. button Press the IMAGE SEL. button on the remote control
  • Sanyo PLC-HF15000L | Owner's Manual - Page 32
    Basic Operation Keystone Correction Press the KEYSTONE button on the remote control to switch the Standard (for Vertical/Horizontal) /Corner correction adjustment. The Standard or Corner correction adjustment dialog box appears. Use the Point ed 7 8 buttons to correct the Standard or Corner
  • Sanyo PLC-HF15000L | Owner's Manual - Page 33
    Side Control Side Control Input Selection Direct Operation INPUT button The input source changes each time you press the INPUT button on the side control as follows: Input 1→Input 2→ ... Before using the INPUT button on the side control or the remote control, you must select a correct input source
  • Sanyo PLC-HF15000L | Owner's Manual - Page 34
    Input Selection Computer Input Source Selection Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Input and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons to select the desired input and then press the Point 8 button
  • Sanyo PLC-HF15000L | Owner's Manual - Page 35
    component signal and the analog RGB signal. When analog RGB signal is not recognized in Y,Pb/Cb,Pr/Cr input source, set to RGB input manually. INPUT 2 MENU Input Selection 35
  • Sanyo PLC-HF15000L | Owner's Manual - Page 36
    to display proper images. If the image is not projected properly, a manual adjustment is required (pp.38, 39). There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on pp.80-82.) PC System Menu Customized Mode (110) set
  • Sanyo PLC-HF15000L | Owner's Manual - Page 37
    parameters. The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC System Menu (p.36). See "Manual PC Adjustment" on pages 38, 39. ✔Note: • Fine sync, Total dots, Position H and Position
  • Sanyo PLC-HF15000L | Owner's Manual - Page 38
    PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 39
    selected when 480i, 575i, 480p, 575p, 720p, 1035i , 1080i or 1080p is selected in the PC System Menu (p.36. • When input computer signal to the projector, PC adjust function will become available. Press the MENU button to close this dialog box. Press the SELECT button to store the data. 39
  • Sanyo PLC-HF15000L | Owner's Manual - Page 40
    desired item and then press the SELECT button. Image select Standard Normal picture level preset on the projector. Real Picture level with improved halftone for graphics. Dynamic For viewing pictures in a bright room. Image 1-10 User preset picture adjustment in the Image adjust Menu. (pp.41-43) 40
  • Sanyo PLC-HF15000L | Owner's Manual - Page 41
    Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Image adjust and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons to select the desired item and then press the SELECT button to display the adjustment
  • Sanyo PLC-HF15000L | Owner's Manual - Page 42
    Computer Input MENU Return to the IMAGE ADJUST Menu. Any settings that have been changed will not be stored. To store the changed settings, be sure to select "LIST" and go to the COLOR MANAGEMENT LIST. COLOR SELECTION MODE Level and phase adjustment palette. Gamma adjustment palette. 4 In the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 43
    controls the operation of the Color Control Devic, which independently and automatically regulates the amount of yellow light passing through the LCD panel, to accurately reproduce both image color and image brightness. Normally leave Auto (default setting). ✔Note: • White balance may change
  • Sanyo PLC-HF15000L | Owner's Manual - Page 44
    on the screen. In this case, the Zoom function is not available. When the original image size is larger than the panel size (2048x1080), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to pan the image. When adjusted, the arrows will turn red. When reached to
  • Sanyo PLC-HF15000L | Owner's Manual - Page 45
    Computer Input Custom adj. Adjust the screen scale and position manually with this function. Press the Point 8 button or the SELECT button at Custom adj. and Custom adj. is displayed on the screen, you can use
  • Sanyo PLC-HF15000L | Owner's Manual - Page 46
    is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear
  • Sanyo PLC-HF15000L | Owner's Manual - Page 47
    , and adjusts itself to optimize its performance. When the Video System is 1035i, 1080i or 1080p, select the system manually. Y, Pb/Cb, Pr/Cr SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p
  • Sanyo PLC-HF15000L | Owner's Manual - Page 48
    the desired item and then press the SELECT button. Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. Dynamic For viewing pictures in a bright room. Image 1-10 User preset picture adjustment in the Image adjust Menu. (p.51) Image select menu 48
  • Sanyo PLC-HF15000L | Owner's Manual - Page 49
    Video Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ed buttons to select Image adjust and then press the Point 8 or the SELECT button. 2 Use the Point ed buttons select the desired item and then press the SELECT button to display the adjustment dialog
  • Sanyo PLC-HF15000L | Owner's Manual - Page 50
    controls the operation of the Color Control Device, which independently and automatically regulates the amount of yellow light passing through the LCD panel, to accurately reproduce both image color and image brightness. Normally leave Auto (default setting). ✔Note: • White balance may change
  • Sanyo PLC-HF15000L | Owner's Manual - Page 51
    scan mode. Off.......... Progressive scan mode is Off. On.......... Progressive scan mode is On. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT button
  • Sanyo PLC-HF15000L | Owner's Manual - Page 52
    of images naturally without changing the center areas. Custom Provides the last stored aspect screen image. Custom adj. Adjusts the screen scale and position manually with this function. Press the Point 8 button at Custom adj. and the Custom adjustment menu is displayed on the screen, you can use
  • Sanyo PLC-HF15000L | Owner's Manual - Page 53
    is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Ceiling Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from
  • Sanyo PLC-HF15000L | Owner's Manual - Page 54
    countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off • T he "Please wait ..." message (except for the filter warning message) • Warning messages displayed when configuring Video delay control
  • Sanyo PLC-HF15000L | Owner's Manual - Page 55
    . Blue Projects a blue background. User Projects a captured image. Black Projects a black background. Lamp mode Allows you to select a lamp mode. 4-Lamps Uses four lamps. 3-Lamps Uses three lamps. 2-Lamps Uses two lamps. Auto: In 3-lamps or 2-lamps mode, automatically and preferentially uses
  • Sanyo PLC-HF15000L | Owner's Manual - Page 56
    projector will turn off after 3 minutes. Lamp interval In 1-lamp mode, this function allows you to specify the timing of switching between the lamps. Off Turns off the lamp mode (Off/User 1-5) and its status (Stored /Free/ Adj.). User 1 and User 2 have stored default values. See page 31 for details
  • Sanyo PLC-HF15000L | Owner's Manual - Page 57
    Main picture or Sub picture. Store Store the adjusted data in the User 1-5. Use the Point ed buttons to select Store and press the SELECT in Screen aspect (p.46, 53). • When P by P is selected in every User 1-5 and the 4:3 function is selected in Screen aspect, PIP button on the remote control
  • Sanyo PLC-HF15000L | Owner's Manual - Page 58
    When displaying multiple screens, eliminates the difference in color between the images that are projected from the projectors. When multiple sets are used simultaneously, this projector allows the user to correct the difference of colors among the sets. Use the Point ed buttons to select Color
  • Sanyo PLC-HF15000L | Owner's Manual - Page 59
    Advanced color matching Select Advanced color matching and press the SELECT button for more detailed settings. Another setting screen will appear. Reset Select Reset and press the SELECT button. Then the confirmation message appears. Press the SELECT button at Yes to reset to the previously stored
  • Sanyo PLC-HF15000L | Owner's Manual - Page 60
    video equipment vary from equipment to equipment. For details, refer to the manual of video equipment. Logo (Logo and Logo PIN code lock settings) This function and set it to User. Then the captured image will be displayed the next time you turn on the projector. To cancel the capture function
  • Sanyo PLC-HF15000L | Owner's Manual - Page 61
    Use the Point ed buttons on the side control or Number buttons on the remote control to enter a number. Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. To enter a Logo PIN code lock Off The screen logo can be changed freely from the Logo Menu (p.60
  • Sanyo PLC-HF15000L | Owner's Manual - Page 62
    . Max.......... Use this mode when you want to increase the cooling effect when operating the projector in high ambient temperature environment. Fan noise is louder than Normal. The filter cleaning icon and "Cleaning is scheduled" message appear. Remote control The eight different remote control
  • Sanyo PLC-HF15000L | Owner's Manual - Page 63
    from the remote control. Power management For reducing power consumption as well as maintaining No signal the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a 4 : 50 certain period. Select one of the following options: Timer left
  • Sanyo PLC-HF15000L | Owner's Manual - Page 64
    control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off
  • Sanyo PLC-HF15000L | Owner's Manual - Page 65
    " and the number will turn red for a moment. Enter the correct PIN code all over again. When the projector is locked with a PIN code, the PIN code lock symbol appears in the Guide. To change the PIN code lock setting Use the Point ed buttons to select OFF, On 1 or On 2. Press
  • Sanyo PLC-HF15000L | Owner's Manual - Page 66
    Projector ID This feature allows users to set serial communication configuration (Projector ID) when several projectors are connected via the RS-232C terminal (serial port) of the projector. Use the Point ed buttons to adjust the Projector ID. Projector the projection lamp when the projector is left
  • Sanyo PLC-HF15000L | Owner's Manual - Page 67
    Video delay control When you want to make a digital processing of a projected image faster, set this function. Use the Point ed buttons, select an item of Off/Low/Mid/ High. Digital processing speed becomes fast by order of Low → Mid → High. High is the fastest. ✔Note: • The following functions are
  • Sanyo PLC-HF15000L | Owner's Manual - Page 68
    . • When the icon as shown in Fig.3 appeared for the first time, replace the filters as soon as possible. If you turn off the projector before you replace the filters, the projector will turn off 3 minutes after the power is turned on next time. Fig.3 This icon is warning you that the remaining
  • Sanyo PLC-HF15000L | Owner's Manual - Page 69
    a few seconds. Test pattern Various test pattern are available for use when setting up the projector. Factory default This function returns all setting values except for User logo, PIN code lock, Logo PIN code lock, Filter counter and Network setting to the factory default settings. Settings 69
  • Sanyo PLC-HF15000L | Owner's Manual - Page 70
    lamp mode. These settings must match those for the rest of the projectors. Select Constant mode from the Lamp mode menu and then specify the same Target value as the projectors , and then overlap the shaded areas by using the lens shift function. When the shaded areas are overlapped with each other
  • Sanyo PLC-HF15000L | Owner's Manual - Page 71
    How to Overlap the Projection Images 5 Set Test pattern to On to display a 50 % white image. The overlap area will be brighter than the non-overlapping area. Adjust the Black level in the Edge blending dialog box to increase the brightness of the non-overlapping area so that the unevenness is
  • Sanyo PLC-HF15000L | Owner's Manual - Page 72
    or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements inside the projector. Such condition may degrade the quality of the projected image. When the symptoms above are noticed, contact your authorized dealer or service center for proper cleaning. 72 Close the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 73
    Electrostatic honeycomb filter ORDER REPLACEMENT FILTER Replacement filter can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector: PLC-HF15000L ● Replacement Filters (sold as a set): 610 354 6902 (service parts code) An
  • Sanyo PLC-HF15000L | Owner's Manual - Page 74
    Reset? appears. Select Yes, then another confirmation box appears. Select Yes again to reset the Filter counter. ✔Note: •Whenever the filters have been replaced, reset the Filter counter, but if the filters were not replaced, do not reset the filter counter, as this could cause product damage. 74
  • Sanyo PLC-HF15000L | Owner's Manual - Page 75
    the lighting lamp (Lamp Mode) by detecting the status of lamp. For example, in 4-lamps mode, if one of the 4 lamps failed, the projector operates with the rest of the lamps, and the lamp mode automatically switches to the 3-lamps mode. To change the lamp mode manually, use the Lamp mode function
  • Sanyo PLC-HF15000L | Owner's Manual - Page 76
    If pieces of glass get into your eyes or mouth, seek medical advice immediately. Follow these steps to replace the lamp. 1 Check the LAMP 1/2/3/4 REPLACE indicators on top of the projector. When any of the indicators blinks rapidly, wait at least 20 minutes until it blinks slowly. After that, go to
  • Sanyo PLC-HF15000L | Owner's Manual - Page 77
    following information to the dealer. ● Model No. of your projector: PLC-HF15000L ● Replacement Lamp Type No.: POA-LMP147 (Service Parts No. 610 350 9051) LAMP HANDLING PRECAUTIONS This projector uses high-pressure lamps which must be handled carefully and properly. Improper handling may
  • Sanyo PLC-HF15000L | Owner's Manual - Page 78
    harsh chemicals might scratch the surface of the lens. Cleaning the Projector Cabinet Turn off the projector, press the Main On/Off Switch to Off AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal
  • Sanyo PLC-HF15000L | Owner's Manual - Page 79
    been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent. - Is the filter clean? Replace the filter with a new one. The projector is shut down; and the LAMP indicator is lighting and other indicators are blinking. When the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 80
    User" or "Off" are not chosen at Logo select function. (See page 60) When the projector is on and you press the input button, an icon other than the Lamp mode icon appears. - That is the Filter connected to the projector. See your computer's instruction manual for the setting. - It takes
  • Sanyo PLC-HF15000L | Owner's Manual - Page 81
    filter with a new one promptly. (See pages 73, 74) - Adjust the focus of the projector. - Check Projection Lens to see if it needs cleaning. ✔Note: M oving the projector The image is darker when 2-lamps mode is selected, compared with 3-lamps mode. Check the lamp mode at SETTING section on page 55
  • Sanyo PLC-HF15000L | Owner's Manual - Page 82
    or the service center. - C heck the lamp status and replace the lamp, or decrease Target value in Constant mode. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 83
    Input H-sync freq. V-sync freq. Screen Lamp mode Lamp control Lamp interval Lamp 1 Lamp 2 Lamp 3 Lamp 4 Language Filter counter Power management Key lock PIN code lock Shutter management Remote control SERIAL NO. Option control No. Remote control Projector Effect Release key Standard Real Dynamic
  • Sanyo PLC-HF15000L | Owner's Manual - Page 84
    Appendix HDMI Input/Video Input Image adjust Contrast Brightness Color Tint Color management Color temp. Red Green Blue Offset Auto picture control Advanced color Sharpness Gamma Noise reduction Progressive Reset Store Video Input System (2) System (3) Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL
  • Sanyo PLC-HF15000L | Owner's Manual - Page 85
    Off Off Blue User Black 4-Lamps 3-Lamps 2-Lamps Constant mode Lamp control Normal Double Target Current Auto Normal Eco1 Eco2 Lamp life control Off Filter control Fan control Remote control RC sensor Power management Direct on Security Projector ID Shutter Video delay control Closed caption Filter
  • Sanyo PLC-HF15000L | Owner's Manual - Page 86
    Condition Check the indicators for the projector condition. The projector is operating normally. POWER green LAMP red Indicators WARNING TEMP. WARNING FILTER SHUTTER red orange blue LAMP REP. orange Projector Condition The projector is off. (The main On/Off switch is OFF position
  • Sanyo PLC-HF15000L | Owner's Manual - Page 87
    indicators on top of the projector (p.76) ✽ ✽ ✽ ✽ ✽ One of the lamps has been operated for more than the total lamp operation time which you specified for the Lamp interval function (P56). WARNING FILTER When the filter detects clogging, the WARNING FILTER indicator lights orange. When this
  • Sanyo PLC-HF15000L | Owner's Manual - Page 88
    is detecting abnormal condition. POWER green LAMP red Indicators WARNING TEMP. WARNING FILTER SHUTTER red orange blue LAMP REP. orange Projector Condition ✽ Fig.1 Fig.2 Fig.3 ✽ ✽ If the Filter counter reached a time set in the timer setting, the icon as shown in Fig.1 appears
  • Sanyo PLC-HF15000L | Owner's Manual - Page 89
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below and less than 230 MHz of Dot Clock. ON-SCREEN RESOLUTION DISPLAY
  • Sanyo PLC-HF15000L | Owner's Manual - Page 90
    of your PC may not be projected correctly. In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. Be sure to follow this procedure, otherwise an image may not be projected on the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 91
    Supported Signal Format for Optional Board When using the optional board (DVI) " 50.000 1920x1080 67.500 60.000 D-1080psf/24(2K) 2048x1080 27.000 48.000 D-1080psf/25(2K) 2048x1080 28.125 50.000 D-1080psf/30(2K) 2048x1080 33.750 60.000 D-1080p/24(2K) 2048x1080 27.000 24.000 5 BNC, S
  • Sanyo PLC-HF15000L | Owner's Manual - Page 92
    Pro (CD-ROM) q Mounting Clamp (for lens mount) q CableTies q Lens Attachment (1 type) (For optional lens) q Light Block Plates (3 types) (For optional lens) q Spacers (For optional lens) q Power Cord Clamp (for AC power cord) q Owner's Manual (CD-ROM) q Quick Reference Guide q PIN Code Label 92
  • Sanyo PLC-HF15000L | Owner's Manual - Page 93
    Unit : POA-SR-160 Smoke Resistant Filter (Replacement Filter) : POA-FIL-160 PJ Link Notice This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class
  • Sanyo PLC-HF15000L | Owner's Manual - Page 94
    Appendix Configurations of Terminals ANALOG TERMINAL(Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 9 +5V Power 2 Green Input 10 Ground (Vert. sync) 3 Blue Input 11 Ground 4 - - - 12 DDC data 5 Ground (Horiz. sync.) 13 Horiz. sync. 6 Ground (Red) 14 Vert. sync.
  • Sanyo PLC-HF15000L | Owner's Manual - Page 95
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. PIN Code Lock No. Logo PIN Code Lock No. Factory default set No: 1 2 3 4* Factory default set
  • Sanyo PLC-HF15000L | Owner's Manual - Page 96
    feet and ceiling mount) Diameter: M10 Depth: 40 mm (1.5748 inch) 420(16.54) 148(5.83) 312(12.28) 4-M8 4-M10 ✔Note: When installing the projector on the ceiling, remove the adjustable feet and use the threaded bores to secure the ceiling mount.
  • Sanyo PLC-HF15000L | Owner's Manual - Page 97
    List of Picture in Picture On-Board Input1 Input2 Optional Interface Board Dsub -DVI Component -S-video Dual SDI Link SDI Appendix Digital Digital Video/ S-video Component Analog PC Digital Scart Analog PC Video/ S-Video Component Analog PC Digital Scart Analog PC Analog PC o o o o o o o
  • Sanyo PLC-HF15000L | Owner's Manual - Page 98
    C05 C06 C07 C08 C0D C0E C0F C10 C1C C1D C3A Function Turn the projector ON Turn the projector OFF (immediately OFF) Select Input 1 Select Input 2 Select Input 3 Select UP Focus DOWN Focus UP Lens shift UP Lens shift DOWN Lens shift LEFT Lens shift RIGHT Auto PC Adj. Keystone UP Keystone DOWN
  • Sanyo PLC-HF15000L | Owner's Manual - Page 99
    anomaly Cooling down at Power Management mode Power Management mode after Cooling down Cooling down after the projector is turned off when the lamps are out. Stand-by mode after Cooling down when the lamps are out. Stand-by mode after Cooling down at the temperature anomaly. Cooling down when the
  • Sanyo PLC-HF15000L | Owner's Manual - Page 100
    KL8A SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Multimedia Projector
MODEL
PLC-HF15000L
Owner’s Manual
✽
Projection lens not included.