Sanyo PLC-WL2503 Owners Manual

Sanyo PLC-WL2503 - 2500 Lumens Manual

Get Sanyo PLC-WL2503 - 2500 Lumens PDF manuals and user guides
UPC - 086483079627
View all Sanyo PLC-WL2503 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-WL2503 manual content summary:

  • Sanyo PLC-WL2503 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-WL2503 Network Supported □ Wired LAN * Refer to the owner's manual below for details about network function. □ Network Set-up and Operation Owner's Manual
  • Sanyo PLC-WL2503 | Owners Manual - Page 2
    to the owner's manual "Network Set-up and Operation." Direct OFF Function With the Direct OFF function, you can disconnect the power cord from the wall outlet or turn off the breaker even during projection (p.20). Interactive function This projector has the interactive software and tools. The
  • Sanyo PLC-WL2503 | Owners Manual - Page 3
    Lens Cover 62 Cleaning the Projection Lens 62 Cleaning the Projector Cabinet 62 Lamp Replacement 63 Resetting the Lamp Counter 64 Appendix 65 Troubleshooting 65 Menu Tree 68 Indicators and Projector Condition 70 Compatible Computer Specifications 71 Technical Specifications 73
  • Sanyo PLC-WL2503 | Owners Manual - Page 4
    of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT
  • Sanyo PLC-WL2503 | Owners Manual - Page 5
    . Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Quick stops
  • Sanyo PLC-WL2503 | Owners Manual - Page 6
    is being used (p.57). Failure to do so may affect the projector life. C AUTION ON CEILING MOUNTING For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted properly, the projector may fall, causing hazards or injury. For details, consult your dealer
  • Sanyo PLC-WL2503 | Owners Manual - Page 7
    instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number PLC-WL2503 Trade Name Sanyo Responsible party : SANYO from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable
  • Sanyo PLC-WL2503 | Owners Manual - Page 8
    " .  Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector. *Kensington is a registered trademark of ACCO Brands Corporation. Note: As for Interactive function, refer to the owner's manual of "Interactive Function" in the application CD-ROM. 8
  • Sanyo PLC-WL2503 | Owners Manual - Page 9
    ① LAN Connection Terminal Connect the LAN cable (refer to the owner's manual of "Network Set-up and Operation"). ② HDMI Connect the HDMI signal from HDMI terminal ② (digital audio). ⑦ CONTROL PORT When controlling the projector with RS-232C, connect the control equipment to this connector with the
  • Sanyo PLC-WL2503 | Owners Manual - Page 10
    detects abnormal condition. This also blinks red when the internal temperature of the projector exceeds the operating range. (pp. 60, 70) ③ LAMP REPLACE indicator Turn yellow when the life of the projection lamp draws to an end. (pp. 63, 70) Top controls ① ② ⑥ 10 ③ ④ ⑤ ① ON/STAND-BY
  • Sanyo PLC-WL2503 | Owners Manual - Page 11
    ⑰ ⑨ ⑯ ASPECT ⑩ ⑮ ⑪ ⑭ ⑬ ⑫ ① ON/STAND-BY button Turn the projector on or off. (pp.18-20) ② AUTO SET button Execute the setting of Auto a screen aspect from 4:3, 16:9 and 16:10. (pp.25,50) ⑯ LAMP button Select a lamp mode. (pp.25, 54) ⑰ P-TIMER button Operate the P-timer function. (pp
  • Sanyo PLC-WL2503 | Owners Manual - Page 12
    is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the
  • Sanyo PLC-WL2503 | Owners Manual - Page 13
    will focus at distance from 2.09' to 3.93' (63.6 cm to 119.7 cm). Note: • This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance. • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting
  • Sanyo PLC-WL2503 | Owners Manual - Page 14
    • VGA cables (Mini D-sub 15 pin) * • Audio cables • HDMI-DVI cable (*One cable is supplied; other cables are not supplied with the projector.) DVI Output Monitor Output or Monitor Input External Audio Equipment Monitor Output Audio Output Audio Input HDMI-DVI cable VGA cable VGA Audio cable
  • Sanyo PLC-WL2503 | Owners Manual - Page 15
    Cables used for connection • Video and Audio cable (RCA x 3) • S-video cable • Audio cable (Cables are not supplied with the projector. ) Installation External Audio Equipment Video and Audio Output S-video Output (Video) (L) (R) Audio Input S-video cable Video and audio cable Audio
  • Sanyo PLC-WL2503 | Owners Manual - Page 16
    used for connection • Audio cables • Scart-VGA cable • Component cable • Component-VGA cable • HDMI cable (Cables are not supplied with this projector.) Component Video Output RGB Scart 21- (Y, Pb/Cb, Pr/Cr) pin Output HDMI Output Audio Output External Audio Equipment Audio Input HDMI cable
  • Sanyo PLC-WL2503 | Owners Manual - Page 17
    other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service center. Connect the projector with all peripheral equipment before turning it on. CAUTION The AC outlet must be near this equipment and must be easily accessible. Connect
  • Sanyo PLC-WL2503 | Owners Manual - Page 18
    .) Note: The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. Video / PC selection window If the projector is locked with a PIN code, PIN code input dialog box will appear. Enter the PIN code as instructed on the next page. Input
  • Sanyo PLC-WL2503 | Owners Manual - Page 19
    the number in a column on page 76 of this manual and keep it on hand. Should the PIN code be missing or forgotten, consult your dealer or service center. PIN Code Input Dialog Box After the OK icon disappears, you can operate the projector. Note: • If the PIN code number is not entered
  • Sanyo PLC-WL2503 | Owners Manual - Page 20
    ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF. DO NOT OPERATE THE PROJECTOR CONTINUOUSLY WITHOUT REST. CONTINUOUS USE MAY RESULT IN SHORTENING THE LAMP LIFE. TURN OFF THE PROJECTOR AND LET STAND FOR ABOUT AN HOUR IN EVERY 24 HOURS. Direct OFF Function You can disconnect the power cord
  • Sanyo PLC-WL2503 | Owners Manual - Page 21
    Operation How to Operate the On-Screen MenHDuMI The projector can be adjusted or set via the On-Screen into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. Remote Control 1 Press the MENU button on the remote control or on the top control
  • Sanyo PLC-WL2503 | Owners Manual - Page 22
    Display the input source information: Input , H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter, Power management, Key lock, PIN code lock and Remote control. (p.59) ⑨ Network See owner's manual of "Network Set-up and Operation". ⑩ Guide The key operation is displayed. 22
  • Sanyo PLC-WL2503 | Owners Manual - Page 23
    some computers can not be fully adjusted with the Auto PC adjustment function. When the image is not provided properly with this operation, manual adjustments are required. (pp.31-32) Remote Control HDMI AUTO SET button Keystone Correction ASPECT Press the KEYSTONE button on the remote control
  • Sanyo PLC-WL2503 | Owners Manual - Page 24
    HDMI Basic Operation Sound Adjustment Direct Operation Volume Press the VOLUME+/- buttons on the remote control or on the top control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Remote Control ASPECT Mute Press the MUTE button on the remote control to
  • Sanyo PLC-WL2503 | Owners Manual - Page 25
    button COMPONENT button FREEZE button D.ZOOM buttons ASPECT INFO. button LAMP button ASPECT button Note: When use the MUTE button to source information: Input, H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter, Power management, Key lock, PIN code lock and Remote control.
  • Sanyo PLC-WL2503 | Owners Manual - Page 26
    . To restore to normal, press the NO SHOW button again or press any other button. When the projected image is captured and is set as User in the Logo selection (p.47), the screen changes each time you press the NO SHOW button as follows. black out → the captured image → normal Note
  • Sanyo PLC-WL2503 | Owners Manual - Page 27
    Computer Input Input Source Selection (Computer 1: RGB) Direct Operation Choose Computer 1(RGB) by pressing the COMPUTER 1 button on the remote control or press the INPUT button on the top control. Before using these buttons, correct input source should be selected through Menu operation as
  • Sanyo PLC-WL2503 | Owners Manual - Page 28
    Computer Input Input Source Selection (Computer 2: RGB) Direct Operation Choose Computer 2 (RGB) by press the COMPUTER 2 button on the remote control or press the INPUT button on the top control. Before using these buttons, correct input source should be selected through Menu operation as
  • Sanyo PLC-WL2503 | Owners Manual - Page 29
    is required. (pp.31-32) There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on page 66.) The preset system is manually adjusted in the PC adjust Menu. The adjusted data can be stored in Mode 1-10. (pp.31-32) PC Systems
  • Sanyo PLC-WL2503 | Owners Manual - Page 30
    The adjusted parameters from the Auto PC adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by function. When the image is not provided properly with this operation, manual adjustments are required (pp.31-32). • The Auto PC adjustment can
  • Sanyo PLC-WL2503 | Owners Manual - Page 31
    PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen
  • Sanyo PLC-WL2503 | Owners Manual - Page 32
    when 480i, 575i, 480p, 575p, 720p, 1035i, or 1080i is selected in the PC System Menu (p.29). • When input computer signal to the projector, PC adjust will become available. Values of Total dots, Horizontal, Vertical, Display area H, and Display area V. Store Menu Vacant 32 Press MENU button to
  • Sanyo PLC-WL2503 | Owners Manual - Page 33
    For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for graphics. Blackboard (Green) For the Image 1- 4 For viewing with the user preset image mode in the Image adjust Menu (see pages 34-35). Image Select Menu
  • Sanyo PLC-WL2503 | Owners Manual - Page 34
    mode Use the Point ◄► buttons to adjust the setting value. Note: • When White balance Red, Green or Blue is adjusted, Color temp. will change to User. • When Blackboard(Green) or Colorboard is selected in Image select, Color temp. will change to Blackboard or Colorboard.
  • Sanyo PLC-WL2503 | Owners Manual - Page 35
    can not display any resolution higher than 1920 x 1200. If your computer's resolution is higher than that, lower the resolution before connecting to the projector. •The image data other than 1280 x 800 is modified to fit the screen size in initial mode. •True and Digital zoom +/- are not available
  • Sanyo PLC-WL2503 | Owners Manual - Page 36
    Computer Input Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment menu is displayed on the screen, you can use the Point ▲▼
  • Sanyo PLC-WL2503 | Owners Manual - Page 37
    Video Input Input Source Selection (Video, S-video) Direct Operation Choose Video or S-video by pressing the VIDEO button or the S-VIDEO button on the remote control or press the INPUT button on the top control. Before using these buttons, correct input source should be selected through Menu
  • Sanyo PLC-WL2503 | Owners Manual - Page 38
    Video Input Input Source Selection (Component, RGB Scart 21-pin, HDMI) Direct Operation Choose Computer 1(Component) or Computer 1(Scart) by pressing the the COMPONENT or COMPUTER 1 button on the remote control or press the INPUT button on the top control; choose HDMI by pressing the HDMI button
  • Sanyo PLC-WL2503 | Owners Manual - Page 39
    video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector can not reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43
  • Sanyo PLC-WL2503 | Owners Manual - Page 40
    For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Cinema Picture mode adjusted with fine tone. Blackboard (Green) For the image projected Image 1-4 For viewing with the user preset image mode in the Image adjust Menu (see pages 41-42). Image select Menu
  • Sanyo PLC-WL2503 | Owners Manual - Page 41
    to deepen blue tone (from 0 to 63). Note: • When the White balance Red, Green, or Blue is adjusted, the Color temp. level will change to User. • Tint can not be selected when the video system is PAL, SECAM, PAL-M, or PAL-N (p.39). • When Blackboard (Green) or Colorboard is selected in Image
  • Sanyo PLC-WL2503 | Owners Manual - Page 42
    options. Off.......... Disabled. L 1.......... For an active picture. L 2.......... For a still picture. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT
  • Sanyo PLC-WL2503 | Owners Manual - Page 43
    Video Input Screen Size Adjustment This projector has the picture screen resize function, which Custom Provide the last stored aspect screen image. Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment menu
  • Sanyo PLC-WL2503 | Owners Manual - Page 44
    Setting Setting This projector has a Setting Menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu.
  • Sanyo PLC-WL2503 | Owners Manual - Page 45
    search works under the following situation. - When turning on the projector by pressing the ON/STAND-BY button. - When pressing the is set to On 1 or On 2, the status of Input and Lamp are displayed every time the signal is switched. • Only the last manual adjustments are required (pp.31-32). 45
  • Sanyo PLC-WL2503 | Owners Manual - Page 46
    to switch between each option. Blue . . . Project a blue background. User . . Project an image captured in the Logo setting. Black . . Project when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough.
  • Sanyo PLC-WL2503 | Owners Manual - Page 47
    select This function decides on the starting-up display from among following options. Off Show the countdown display only. Default..... Show the factory-set logo. User......... Show the image you captured. Setting 47
  • Sanyo PLC-WL2503 | Owners Manual - Page 48
    projected image. After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector. To cancel the capture function, select Yes in the "Quit?" confirmation box. Note: • Before capturing an image
  • Sanyo PLC-WL2503 | Owners Manual - Page 49
    Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and
  • Sanyo PLC-WL2503 | Owners Manual - Page 50
    is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, screen. 16:10 ....16:10 is the aspect of the LCD panel. The orignal Screen Menu is available. HDMI setup equipment. For details, refer to the owner's manual of your Digital RGB equipment. When the
  • Sanyo PLC-WL2503 | Owners Manual - Page 51
    off the projector. Refer to the owner's manual of "Network Set-up and Operation". Note: • Factory default is Network. • When Eco is selected and the projector is in Stand-by, the communication of RS-232C serial port is not available. Power management Timer left before Lamp is off
  • Sanyo PLC-WL2503 | Owners Manual - Page 52
    turned on just by connecting the AC power cord to a wall outlet. Note: Be sure to turn off the projector properly (see "Turning Off the Projector" on page 20). If the projector is turned off in the incorrect sequence, the Direct on function does not work properly. P-timer This function allows
  • Sanyo PLC-WL2503 | Owners Manual - Page 53
    Closed caption Closed caption is a printed version of the program sound or other information displayed on the screen. If the input signal contains Closed captions, you can turn on the feature and switch the channels. Press the Point ▲▼ buttons to select Off, CC1, CC2, CC3 or CC4. If the Closed
  • Sanyo PLC-WL2503 | Owners Manual - Page 54
    allows you to change brightness of the screen. Normal....... .Normal brightness. Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Remote control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary
  • Sanyo PLC-WL2503 | Owners Manual - Page 55
    or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Setting PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off
  • Sanyo PLC-WL2503 | Owners Manual - Page 56
    -digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, PIN code and the number will turn red for a moment. Enter the correct PIN code all over again
  • Sanyo PLC-WL2503 | Owners Manual - Page 57
    . On 2......... Faster than On 1 mode. Select this mode when using the projector in higher altitudes than above where the fans have lesser cooling effect. Note: lamp life is reached. When replacing the projection lamp, reset lamp counter. See "Resetting the Lamp Counter" on page 64. Note: The Lamp
  • Sanyo PLC-WL2503 | Owners Manual - Page 58
    or No show (p.26). Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs setting values except for the User logo, PIN code lock, Logo PIN code lock, Lamp counter and Filter counter to the factory default
  • Sanyo PLC-WL2503 | Owners Manual - Page 59
    of the image signal being projected and the operation of the projector. HDMI Direct Operation Press the INFO. button on the remote control The selected language is displayed. Lamp status The selected lamp mode is displayed. Lamp counter The cumulative lamp operating time is displayed. Power
  • Sanyo PLC-WL2503 | Owners Manual - Page 60
    can not be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service center. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Panel WARNING emit a red
  • Sanyo PLC-WL2503 | Owners Manual - Page 61
    dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service center for proper cleaning. Latch Filter cover TOP mark Pull
  • Sanyo PLC-WL2503 | Owners Manual - Page 62
    its vicinity. The explosion or fire hazard may occur even after the AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal parts may be damaged not only by the flammable air spray but also by
  • Sanyo PLC-WL2503 | Owners Manual - Page 63
    Screws Handle Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-WL2503 : POA-LMP141 (Service Parts No
  • Sanyo PLC-WL2503 | Owners Manual - Page 64
    with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of
  • Sanyo PLC-WL2503 | Owners Manual - Page 65
    Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. -Make sure you have properly connected the projector to peripheral equipment as described on pages 14-16. -Make sure all equipment is connected to AC outlet and the power is
  • Sanyo PLC-WL2503 | Owners Manual - Page 66
    if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 15 seconds to display an image after turning on the
  • Sanyo PLC-WL2503 | Owners Manual - Page 67
    center. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the
  • Sanyo PLC-WL2503 | Owners Manual - Page 68
    / Green Image 2 Image 3 Image 4 Image adjust Contrast Brightness Color temp. Red Green Blue Sharpness Gamma Reset Store 0-63 0-63 XLow Low Mid High User 0-63 0-63 0-63 0-15 0-15 Yes / No Image 1 Image 2 Image 3 Image 4 Screen Normal True Full Custom Custom adj. Digital zoom + Digital zoom
  • Sanyo PLC-WL2503 | Owners Manual - Page 69
    Full Zoom Wide Natural wide Custom Custom adj. 0-63 0-63 0-63 0-63 XLow Low Mid High User 0-63 0-63 0-63 0-15 0-15 Off L 1 L 2 Off L 1 L 2 Film On 1 / On 2 Video delay control Off / On Lamp counter Lamp counter Lamp counter reset Filter counter Warning log Factory default Filter counter H
  • Sanyo PLC-WL2503 | Owners Manual - Page 70
    the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. • • • green blinks green. • • • red blinks red. • • • off When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow
  • Sanyo PLC-WL2503 | Owners Manual - Page 71
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC
  • Sanyo PLC-WL2503 | Owners Manual - Page 72
    of your PC may not be projected correctly. In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. Be sure to follow this procedure, otherwise an image may not be projected on the
  • Sanyo PLC-WL2503 | Owners Manual - Page 73
    Quick Reference Guide Interactive Software and Manual(CD-ROM) Safety Manual Interactive Pen AC Power Cord Interactive Pointer Remote Control Interactive USB Cable Batteries Cable Holder VGA Cable PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are
  • Sanyo PLC-WL2503 | Owners Manual - Page 74
    CA-COMPVGA VGA-Cable (10 m) TERMINAL COVER : KA-MC-DB10 : POA-TC-WL2500 The Terminal Panel Replacement It is recommended to attach the terminal cover to hide the unsightly cables when hanging the projector from the ceiling. The optional terminal cover set (including Terminal Cover, Terminal Cover
  • Sanyo PLC-WL2503 | Owners Manual - Page 75
    Appendix Configurations of Terminals COMPUTER IN 1 /COMPONENT IN Terminal: Analog RGB (Mini D-sub 15 pin) LAN TERMINAL 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red (R/Cr) Input 2 Green (G/Y) Input 3 Blue (B/Cb) Input 4 ----5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) 9 5V
  • Sanyo PLC-WL2503 | Owners Manual - Page 76
    the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. PIN Code Lock No. Factory default illustration). Cable Holder (supplied) Interactive Camera USB Cable (supplied) 76 Infrared Remote Receiver
  • Sanyo PLC-WL2503 | Owners Manual - Page 77
    56(166.7) 6.29(159.8) Appendix Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M5 Depth: 0.394(10.0) 5.65(143.5) 0.70(17.8) 0.34(8.7) projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports
  • Sanyo PLC-WL2503 | Owners Manual - Page 78
    KJ8AE
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Multimedia Projector
MODEL
PLC-WL2503
Owner’s Manual
Network Supported
□ Wired LAN
*
Refer to the owner’s manual
below for details about network
function.
□
Network Set-up and Operation