Sanyo PLC XE40 Owners Manual - Page 53

Maintenance and Cleaning, Warning Indicator

Get Sanyo PLC XE40 - XGA LCD Projector PDF manuals and user guides View all Sanyo PLC XE40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Maintenance & Cleaning Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. When the temperature inside the projector reaches a certain level, the projector is automatically shut down to avoid overheating. The POWER indicator is blinking while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the POWER ON-OFF button. Top Control WARNING blinking red POWER WARNING LAMP REPLACE ✔Note: • After the temperature inside the projector returns to normal, the WARNING indicator still continues to blink. When the projector is turned on again, the WARNING indicator stops blinking. Then check the matters below: - Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if ventilation slots are not blocked. - Is the projector not installed near the ventilation duct of air-conditioning equipment which may be hot? Install the projector away from the ventilation duct of airconditioning equipment. - Are the air filters clean? Clean the air filters periodically. (p. 54) The projector is shut down and the WARNING indicator emits a red light. When the projector detects an abnormal condition, it is automatically shut down to protect the inside and the WARNING indicator is red. In this case, disconnect the AC power cord and reconnect it, and then turn the projector on once again for check. If the projector cannot be turned on and the WARNING indicator emits a red light, disconnect the AC power cord and contact the service station for check and repair. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER THE ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Control WARNING emit a red light POWER WARNING LAMP REPLACE 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
53
The WARNING indicator shows the state of the function which protects the projector.
Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance.
Top Control
Warning Indicator
The pr
oject
or is shut do
wn and the W
ARNING
indicat
or is blinking r
ed.
When the temperature inside the projector reaches a
certain level, the projector is automatically shut down to
avoid overheating.
The POWER indicator is blinking while
the projector is being cooled down.
When the projector has
cooled down enough (to its normal operating temperature),
it can be turned on again by pressing the POWER ON-OFF
button.
✔
Note:
• After the temperature inside the projector returns to normal, the
WARNING indicator still continues to blink.
When the projector is
turned on again, the WARNING indicator stops blinking.
Then check the matters below:
–
Did you provide appropriate space for the projector to be
ventilated?
Check the installing condition to see if
ventilation slots are not blocked.
–
Is the projector not installed near the ventilation duct of
air-conditioning equipment which may be hot? Install the
projector away from the ventilation duct of air-
conditioning equipment.
–
Are the air filters clean?
Clean the air filters periodically.
(p. 54)
WARNING
emit a red light
Top Control
The pr
oject
or is shut do
wn and the W
ARNING
indicat
or emits a r
ed light.
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside and the
WARNING indicator is red.
In this case, disconnect the AC
power cord and reconnect it, and then turn the projector on
once again for check.
If the projector cannot be turned on
and the WARNING indicator emits a red light, disconnect
the AC power cord and contact the service station for check
and repair.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE AC
POWER CORD CONNECTED UNDER THE
ABNORMAL CONDITION.
IT MAY RESULT IN
FIRE OR ELECTRIC SHOCK.
Maintenance and Cleaning
REPLACE
POWER
WARNING
LAMP
REPLACE
POWER
WARNING
LAMP
WARNING
blinking red
Maintenance & Cleaning