Sanyo PLC-XL51 Owner's Manual
Sanyo PLC-XL51 - 2700 Lumens Manual
 |
UPC - 086483072222
View all Sanyo PLC-XL51 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-XL51 manual content summary:
- Sanyo PLC-XL51 | Owner's Manual - Page 1
Multimedia Projector MODEL PLC-XL51 Network Supported ❏Wireless LAN IEEE802.11b/g ❏Wired LAN 100-Base-TX/10-Base-T Memory Viewer ❏SD Memory Card Viewer ✽Refer to the owner's manual below for details about network and memory viewer function. ■Network Set-up and Operation (For - Sanyo PLC-XL51 | Owner's Manual - Page 2
advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆Large Screen in Limited Space Short focus lens allows you to project large images from - Sanyo PLC-XL51 | Owner's Manual - Page 3
62 Lamp Replacement 63 Lamp Replacement Counter 64 Appendix 65 Troubleshooting 65 Menu Tree 68 Indicators and Projector Condition 70 Compatible Computer Specifications 71 Technical Specifications 72 Optional Parts 73 Configurations of Terminals 74 Dimensions 74 PIN Code Number - Sanyo PLC-XL51 | Owner's Manual - Page 4
manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER - Sanyo PLC-XL51 | Owner's Manual - Page 5
and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when it is - Sanyo PLC-XL51 | Owner's Manual - Page 6
in an unsuitable transport case. This may cause damage to the projector. For information about transporting the projector by courier or any other transport service, consult your dealer. - Do not put the projector in a case before it is cooled enough. Exhaust Vent (Hot air exhaust) Air Intake - Sanyo PLC-XL51 | Owner's Manual - Page 7
Instructions Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause fire hazard. Side A Side B CAUTION - Do not put anything or sit on the projector, otherwise, it may fall down or cause failure of the projector - Sanyo PLC-XL51 | Owner's Manual - Page 8
the equipment. Model Number(s) Trade Name Responsible party Address Telephone No. : PLC-XL51 : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street, Chatsworth, California 91311 : (818)998-7322 AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirement - Sanyo PLC-XL51 | Owner's Manual - Page 9
Part Names and Functions Front q Back w e r t Bottom y u i o !0 ✽ !3 !1 !2 q Infrared Remote Receiver CAUTION The Infrared Remote Receiver sticks out of the cabinet surface. If the Infrared Remote Receiver is put on the wall or floor directly, the Infrared Remote Receiver may damage. w - Sanyo PLC-XL51 | Owner's Manual - Page 10
q LAN Connection Terminal Connect the LAN cable (refer to the owner's manual "Network Set-up and Operation"). w SERVICE PORT This jack is used to service the projector. e COMPUTER IN 1 Connect output signal from a computer, or RGB scart 21pin video output to this terminal (pp.16, 18). When the cable - Sanyo PLC-XL51 | Owner's Manual - Page 11
condition. - Blinks red when the internal temperature of the projector exceeds the operating range (pp.60, 70). r LAMP REPLACE indicator Turn yellow when the life of the projection lamp draws to an end (pp.63, 70). t ON/STAND-BY button Turn the projector on or off (pp.20-21). i SELECT button - Sanyo PLC-XL51 | Owner's Manual - Page 12
following precautions: - Do not bend, drop, or expose the remote control to moisture or heat. - For cleaning, use a soft dry cloth. Do not apply benzene, thinner, spray, or any other chemicals. 12 q ON/STAND-BY button Turn the projector on or off (pp.20, 21). w COMPONENT button Select COMPONENT - Sanyo PLC-XL51 | Owner's Manual - Page 13
. ● Risk of explosion if a battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule and guidelines. Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing any button. See the right - Sanyo PLC-XL51 | Owner's Manual - Page 14
to the plane of the screen. A A -0.131' ( -4.0 cm) 0.265' ( 8.1 cm) 80" 60" ✔Note: •This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance. •The brightness in the room has a great influence on picture quality. It is recommended to limit the - Sanyo PLC-XL51 | Owner's Manual - Page 15
Mounting the Rear Leg and the Stand Rear Leg 1 Turn off the projector and unplug the AC power cord. 2 Secure the rear leg with the four (4) screws. Installation Screw Rear leg Stand* 1 Turn off the projector and unplug the AC power cord. 2 Secure the stand with three (3) sets of the screw with a - Sanyo PLC-XL51 | Owner's Manual - Page 16
Cables (Mini Plug: stereo) (*One cable is supplied; other cables are not supplied with the projector.) Audio Output Audio cable (stereo) Monitor Output Monitor optional cables. 16 Unplug the power cords of both the projector and external equipment from the AC outlet before connecting the cables. - Sanyo PLC-XL51 | Owner's Manual - Page 17
Plug: stereo) (Cables are not supplied with the projector.) Installation External Audio Equipment S-Video Output Composite Video and Audio Output (Video) (L) (R) Audio Input S-Video cable Video and audio cable Audio cable (stereo) S-VIDEO IN (Video) (L) (R) VIDEO IIN AUDIO IN AUDIO OUT - Sanyo PLC-XL51 | Owner's Manual - Page 18
Component Cable (Cables are not supplied with the projector.) External Audio Equipment RGB Scart 21pin Output Component Video Output (Y, Pb/Cb, Pr/Cr the projector's built-in speaker is not available. •See page 73 for ordering optional cables. 18 Unplug the power cords of both the projector and - Sanyo PLC-XL51 | Owner's Manual - Page 19
the risk of electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning it on. Installation CAUTION The AC outlet - Sanyo PLC-XL51 | Owner's Manual - Page 20
that was selected the last time and the Lamp mode status icon (see page 51) will appear on the screen. If the projector is locked with a PIN code, a PIN code Input Dialog Box appears. Enter the PIN code as instructed below. Enter a PIN code Select a number by pressing the Point ed buttons, and then - Sanyo PLC-XL51 | Owner's Manual - Page 21
remote control, and "Power off?" appears on the screen. 2 Press the ON/STAND-BY button again to turn off the projector. The POWER POWER indicator is blinking, the lamp is being cooled down and the projector cannot be turned on. Wait until the POWER indicator stops blinking to turn on the projector - Sanyo PLC-XL51 | Owner's Manual - Page 22
projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or on the remote press the MENU button again. Top Control Remote Control ✔Note: •The selected item is not - Sanyo PLC-XL51 | Owner's Manual - Page 23
items in video source when 480i, 575i, 480p, 575p, 720p, 1035i or 1080i is For video source selected. q w e r t y u i o !0 q Guide Window Shows projector's operating configurations (pp.45-55). o Wired Menu See owner's manual "Network Set-up and Operation". !0 Wireless Menu See owner's manual - Sanyo PLC-XL51 | Owner's Manual - Page 24
being corrected turns red. •The arrows disappear at the maximum correction. •If you press the KEYSTONE button on the top control or on the remote control once more while the keystone dialog box is being displayed, the keystone adjustment is canceled. •The adjustable range can be limited depending on - Sanyo PLC-XL51 | Owner's Manual - Page 25
seconds. Top Control VOLUME+/buttons Mute Press the MUTE button on the remote control to temporarily turn off the sound. To turn the sound back the volume; press the Point 7 button to turn down the volume. Remote Control VOLUME+ button MUTE button VOLUME- button Approximate level of the volume. - Sanyo PLC-XL51 | Owner's Manual - Page 26
press any other button. When the projected image is captured and is set as "User" in the Logo selection (p.47), the screen changes each time you press the lamp power consumption and extends the lamp life. 26 Remote Control COMPUTER 1/2 buttons NETWORK button COMPONENT button S-VIDEO button VIDEO - Sanyo PLC-XL51 | Owner's Manual - Page 27
INPUT button INPUT button Computer 1 Computer 2* Video Wired Remote Control Wireless COMPUTER 1 button COMPUTER 2 button *See Notes can accept only the RGB signal. • Wired and Wireless are for the Network function. See owner's manual "Network Set-up and Operation". Input Menu Input Menu - Sanyo PLC-XL51 | Owner's Manual - Page 28
XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If computer is selected as a signal source, the projector the connection between your computer and the projector. (See "Troubleshooting" on page 65.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The - Sanyo PLC-XL51 | Owner's Manual - Page 29
with the AUTO PC button on the remote control. Remote Control AUTO PC button Menu Operation Auto in the Auto PC Adjustment can be stored in the projector. Once parameters are stored, the setting can be is not provided properly with this operation, manual adjustments are required (pp.30-31). • - Sanyo PLC-XL51 | Owner's Manual - Page 30
those signal formats. The projector has five independent memory areas (Mode 1-5) to store those parameters manually adjusted, which allows you from 0 to 31). Total dots Use the Point 7 8 buttons to adjust the number of total dots in one horizontal period to match your PC image. Status (Stored/Free - Sanyo PLC-XL51 | Owner's Manual - Page 31
Input Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select "Reset" and press the SELECT button. A confirmation - Sanyo PLC-XL51 | Owner's Manual - Page 32
IMAGE button on the remote control. Dynamic For viewing pictures in a bright room. Standard Normal picture level preset on the projector. Real Picture level the wall color from the preset four colors. See the next page. Image 1-4 User preset image in the Image Adjust Menu (p.35). Remote Control - Sanyo PLC-XL51 | Owner's Manual - Page 33
in a bright room. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. Blackboard(Green) the similar color to the wall color from the preset four colors. Press the SELECT button to choose the color. Image 1-4 User preset image in the Image - Sanyo PLC-XL51 | Owner's Manual - Page 34
Computer Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item, and then press the SELECT button. The - Sanyo PLC-XL51 | Owner's Manual - Page 35
aspect ratio (16:9) by expanding the image width uniformly. This function can be used to provide the squeezed video signal at 16:9. Full Provide the full screen image. ✔Note: •The Screen Menu cannot be operated when 720p, 1035i, or 1080i is selected in the PC System Menu (p.28). •This projector - Sanyo PLC-XL51 | Owner's Manual - Page 36
projected image can be also expanded by pressing the D.ZOOM e button on the remote control. Digital zoom - Digital zoom - is used to reduce the image image can be also compressed by pressing the D.ZOOM d button on the remote control. To exit the Digital zoom +/- mode, press any button except the - Sanyo PLC-XL51 | Owner's Manual - Page 37
performance. The projector selects connection in the following order: 1. Component 2. S-video 3. Video Remote Control VIDEO button Wired Wireless S-VIDEO button COMPONENT button Input Menu icon Input Menu Move the pointer to Video and press the SELECT button. Video When the video input signal - Sanyo PLC-XL51 | Owner's Manual - Page 38
the SELECT button. Remote Control COMPUTER 1 button Wireless *See Note at the bottom of this page. Input Menu Input Menu icon RGB (Scart) When the input source is coming from video equipment connected to the COMPUTER IN 1 terminal with a Scart-VGA Cable (not supplied - Sanyo PLC-XL51 | Owner's Manual - Page 39
desired system and then press the SELECT button. Video Input Video or S-Video Auto The projector automatically detects an incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If - Sanyo PLC-XL51 | Owner's Manual - Page 40
IMAGE button on the remote control. Dynamic For viewing pictures in a bright room. Standard Normal picture level preset on this projector. Cinema Picture level to the wall color from the preset four colors. Image 1-4 User preset image in the Image Adjust Menu (pp.42-43). Remote Control IMAGE - Sanyo PLC-XL51 | Owner's Manual - Page 41
Video Input in a bright room. Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture with fine tone. the similar color to the wall color from the preset four colors. Press the SELECT button to choose the color. Image1-4 User preset image in the Image - Sanyo PLC-XL51 | Owner's Manual - Page 42
and then press the SELECT button. Selected Image level Use the Point 7 8 buttons to adjust the value. ✔Note: •The Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N. •After adjusting the White balance Red, Green or Blue, the Color temp. level will change to "Adj.". 42 - Sanyo PLC-XL51 | Owner's Manual - Page 43
...... F or watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset be selected when 480p, 575p, 720p, 1035i, or 1080i is selected (p.39). Video Input Store item Image Level Menu Move the red frame pointer to an image item - Sanyo PLC-XL51 | Owner's Manual - Page 44
Video Input Screen Size Adjustment This projector has the picture screen resize function, which desired function and then press the SELECT button. Normal Provide the image at a normal video aspect ratio of 4:3. Screen Menu Screen Menu icon Move the red frame pointer to the desired function - Sanyo PLC-XL51 | Owner's Manual - Page 45
cord is unplugged. Store 2......Store the Zoom setting even when the AC power cord is unplugged. Reset........Reset the Zoom adjustment when the projector is turned off or the AC power cord is unplugged. Keystone This function corrects distortion of a projected image. Select either Store or Reset - Sanyo PLC-XL51 | Owner's Manual - Page 46
projector is turned off or the AC power cord is unplugged. Reset........Reset the Uniformity adjustment when the projector is turned off or the AC power when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright - Sanyo PLC-XL51 | Owner's Manual - Page 47
to the Logo select function and set it to "User." Then the captured image is displayed when the projector is turned on next time or the NO SHOW 40-41). •A signal from a computer can be captured up to XGA(1024x 768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i. - Sanyo PLC-XL51 | Owner's Manual - Page 48
. If you entered an incorrect PIN code, "Logo PIN code" and the number turns red. Enter a correct Logo PIN code all over again. Change the If you lost the number, you could no longer change the Logo PIN code setting. For details on PIN code setting, refer to relevant instructions of the PIN code - Sanyo PLC-XL51 | Owner's Manual - Page 49
from a ceiling-mounted projector. Rear When this the status of Input and Lamp are displayed every time VIDEO, S-VIDEO, COMPONENT, or NETWORK button on the remote control while Input search is on. • Sync on Green signal does not support Input search. • Input search does not work for Wired/ Wireless - Sanyo PLC-XL51 | Owner's Manual - Page 50
function will stop when turning off the projector. Refer to the owner's manual "Network Setup and Operation." Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and - Sanyo PLC-XL51 | Owner's Manual - Page 51
the lamp power consumption and extends the lamp life. Remote control This projector provides two different remote control codes; the factory-set, initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when several projectors or video - Sanyo PLC-XL51 | Owner's Manual - Page 52
to enter a PIN code to operate the projector once the power cord is unplugged; as long as the AC power cord is connected, the projector can be operated without a PIN code. Whenever you change the PIN code lock setting or the PIN code (a four-digit number), you are required to enter the PIN code - Sanyo PLC-XL51 | Owner's Manual - Page 53
PIN code The PIN code can be changed to your desired four-digit number. Select "PIN code change" with the Point d button, and press the SELECT page 75, and keep it securely. If you forget your PIN code, the projector can no longer be started. Alarm This function allows you to configure the Alarm - Sanyo PLC-XL51 | Owner's Manual - Page 54
fans properly may affect the projector life. ✔Note: •When the Factory default function is executed, all the warning log records will be deleted. Lamp counter This function is used to reset the lamp counter. When the lamp life is left less than 100 hours, the Lamp replacement icon appears on the - Sanyo PLC-XL51 | Owner's Manual - Page 55
Test pattern Various test patterns are available for use when setting up the projector. Factory default This function returns all setting values except for the user logo, PIN code lock, Logo PIN code lock, the lamp counter, and the filter counter to the factory default settings. Factory default - Sanyo PLC-XL51 | Owner's Manual - Page 56
while the AC power cord is connected to an outlet even if the projector detects vibrations. •The alarm will stop, as the AC power cord is connected enter the four-digit PIN code number. Release the alarm setting Press the F button and enter the four-digit PIN code number within about 10 seconds. (The - Sanyo PLC-XL51 | Owner's Manual - Page 57
Antitheft Alarm Function Other settings Change the PIN code 1 Press the F button and enter the four-digit PIN code number within about 10 seconds. The ALARM indicator blinks red for a few seconds and a high-pitched confirmation sound is produced. 2 While the indicator is blinking, enter a - Sanyo PLC-XL51 | Owner's Manual - Page 58
the specified battery for this projector. Using other types of battery may cause accident or fire hazard. Replacement Battery: SANYO Ni-MH BATTERY PACK Part No. 645 089 8587 How to replace the rechargeable battery pack 1 Unplug the AC power cord from a wall outlet. 2 Set the Alarm function - Sanyo PLC-XL51 | Owner's Manual - Page 59
this projector. Do not use in other products or this may cause accident. ● Do not throw the short-circuit battery terminals with metal objects. Do not store with metal objects or in a metal case. ● The rechargeable battery pack has a limited number of charge cycles and eventually need to be replaced - Sanyo PLC-XL51 | Owner's Manual - Page 60
cannot be turned on and the WARNING indicator lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Indicators WARNING emit a red light - Sanyo PLC-XL51 | Owner's Manual - Page 61
projector. Air filter Pull up and remove. ✔Note: •When cleaning the air filter, protect the infrared remote receiver with a soft cloth to avoid damaging it. • If the filter is heavily clogged and unable to clean, replace it with a new one. Consult your dealer for details. Replacement Filter Part - Sanyo PLC-XL51 | Owner's Manual - Page 62
not use abrasive cleaners, solvents, or other harsh chemical cleaners to avoid damaging the projection window. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning. Gently wipe the projector body with a soft dry cleaning cloth. When it is heavily soiled, use a small amount of mild - Sanyo PLC-XL51 | Owner's Manual - Page 63
avoid damaging it. Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XL51 : POA-LMP121 (Service Parts No. 610 337 - Sanyo PLC-XL51 | Owner's Manual - Page 64
should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted - Sanyo PLC-XL51 | Owner's Manual - Page 65
monitor output when connected to the projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. - See if the selected system is corresponding with your computer or video equipment (see pages 28, 39). - Select - Sanyo PLC-XL51 | Owner's Manual - Page 66
Lamp replace indicator. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. (See page 63) - Check the Input signal, color system, video AUDIO OUT is plugged in, the projector's built-in speaker is not power management function in the Setting. The power - Sanyo PLC-XL51 | Owner's Manual - Page 67
attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service. The CE Mark is a Directive - Sanyo PLC-XL51 | Owner's Manual - Page 68
Menu Tree Computer Input/Video Input Input Computer 1 Computer 2 Video Wired Wireless RGB RGB( Scart ) Quit Go to System (1) Auto Video S-Video Component Quit Go to System (1) Go to System (2) or (3) Go to System (3) Go to System (3) Go to System (2) See owner's manual "Network Setup and - Sanyo PLC-XL51 | Owner's Manual - Page 69
Video Off/ Countdown off / On Logo select Off Capture Default User Yes / No Logo PIN code lock Logo PIN code entry Power management On start Lamp control Remote control Security Off Ready Shut down Timer(1-30 Min) Quit On / Off Normal / Auto / Eco Code 1 / Code 2 Key lock Off Projector Remote - Sanyo PLC-XL51 | Owner's Manual - Page 70
, see pages 56-57. Indicators POWER red/green WARNING red LAMP REPLACE yellow Projector Condition The projector is off. (The AC power cord is unplugged.) The projector is preparing for stand-by or the projection lamp is ✽ being cooled down. The projector cannot be turned on until cooling - Sanyo PLC-XL51 | Owner's Manual - Page 71
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When these modes are selected, - Sanyo PLC-XL51 | Owner's Manual - Page 72
Projection Image Size (Diagonal) Projection Lens Distance (Screen - Projector) Projection Lamp Adjustable from 60" to 80" F 1.85 lens with f 4.83 mm with manual focus -0.131' - 0.265' (-4.0 cm - 8.1 cm) 275 W Interface Video Input Jack S-Video Input Jack Audio Input Jacks Component Input Jacks - Sanyo PLC-XL51 | Owner's Manual - Page 73
Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label Alarm Label Stand Ferrite Core Cable Tie Network Application (CD-ROM) ●The specifications are subject to change without notice. ●LCD panels are manufactured to the - Sanyo PLC-XL51 | Owner's Manual - Page 74
sync. 15 DDC clock/ ----- SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN 12 34 5 6 78 Dimensions Serial 1 RXD 2 ----3 ----4 0.41 (10.5) 0.17 (4.2) 7.75 (196.8) 1.87 (47.5) 7.09 (180) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.393 (10.0) 16.73 (425) 16.59 (421.5) 19.49 (495) 9.37 - Sanyo PLC-XL51 | Owner's Manual - Page 75
this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. number be changed, the factory set number will be invalid. While the projector is locked with the PIN code... Put the label below (supplied) to a prominent place of the projector - Sanyo PLC-XL51 | Owner's Manual - Page 76
supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer 1 Computer 2 Video Wired Wireless RGB RGB (Scart) RGB Auto Video S-Video - Sanyo PLC-XL51 | Owner's Manual - Page 77
KV7A SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
 |
 |
Multimedia Projector
MODEL
PLC-XL51
Owner’s Manual
Network Supported
❏
Wireless LAN
IEEE802.11b/g
❏
Wired LAN
100-Base-TX/10-Base-T
Memory Viewer
❏
SD Memory Card Viewer
✽
Refer to the owner’s manual below for details
about network and memory viewer function.
■
Network Set-up and Operation
(For Windows / For Macintosh)
■
Memory Viewer function
■
PJ Network Manager (For Windows)