Sanyo PLC-XTC50L Owners Manual

Sanyo PLC-XTC50L - XGA LCD Projector Manual

Get Sanyo PLC-XTC50L - XGA LCD Projector PDF manuals and user guides
UPC - 086483073069
View all Sanyo PLC-XTC50L manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XTC50L manual content summary:

  • Sanyo PLC-XTC50L | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-XTC50L *Projection lens is optional. Owner's Manual
  • Sanyo PLC-XTC50L | Owners Manual - Page 2
    The projector monitors the condition of the filter and replaces a filter automatically when it detects the clogging. ◆ Power Management The Power management function reduces power consumption and maintains lamp life (p.54). ✔Notes: • The On-Screen Menu and figures in this manual may differ
  • Sanyo PLC-XTC50L | Owners Manual - Page 3
    Instructions 60 Replacing the Filter Cartridge 61 Resetting the Filter Counter 62 Resetting the Scroll Counter 62 Auto Lamp Selection System 63 Lamp Replacement 64 Warning Indicators 66 Cleaning the Projection Lens 67 Cleaning the Projector Cabinet 67 Appendix 68 Troubleshooting
  • Sanyo PLC-XTC50L | Owners Manual - Page 4
    of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT
  • Sanyo PLC-XTC50L | Owners Manual - Page 5
    dropped or the cabinet has been damaged. f.When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics
  • Sanyo PLC-XTC50L | Owners Manual - Page 6
    parts of the exhaust vent, especially screws and metallic parts. These areas will become hot while the projector projector immediately and replace the filter cartridge. Blocking the air vents and leaving the projector uncleaned for a long time may not only damage the projector and may require costly
  • Sanyo PLC-XTC50L | Owners Manual - Page 7
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in
  • Sanyo PLC-XTC50L | Owners Manual - Page 8
    Instructions Moving the Projector Use the hand grip when moving the projector. Replace the lens cap and retract the adjustable feet to prevent damage to the lens and cabinet when carrying. When the projector is not in use for an extended period, put it into a suitable case to protect the projector
  • Sanyo PLC-XTC50L | Owners Manual - Page 9
    Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number(s) : PLC-XTC50L Trade Name : Sanyo Responsible
  • Sanyo PLC-XTC50L | Owners Manual - Page 10
    Controls and Indicators t Lens Cover y Speaker u Projection Lens(Optional) i Adjustable Feet o Power Cord Connector !0 Optional Parts Attachment ty u y i Back !2 !1 ✽ o !0 !3 !4 !5 !4 !6 Bottom i !7 !1 Infrared Remote Receiver (Back) !2 Lamp Cover !3 Filter Cover !4 Exhaust Vent CAUTION
  • Sanyo PLC-XTC50L | Owners Manual - Page 11
    Side Terminal t y u Part Names and Functions q we r i o q COMPUTER INPUT TERMINAL (DIGITAL) Connect the computer output signal (Digital DVI-D type) to this terminal. The HDTV (HDCP compatible) signal can
  • Sanyo PLC-XTC50L | Owners Manual - Page 12
    Part Names and Functions Side Terminal !0 !1 !2 !3 !0 USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with the supplied USB cable (p.20). !1 R/C JACK When using the wired
  • Sanyo PLC-XTC50L | Owners Manual - Page 13
    Part Names and Functions o !0 !1 !2 !3 i q WARNING TEMP. indicator - Lights red light when the projector detects an abnormal condition or the filter cartridge is not installed. - Blinks red when the internal temperature of the projector exceeds the operating range (pp.66, 75). w LAMP 1 REPLACE
  • Sanyo PLC-XTC50L | Owners Manual - Page 14
    Part Names and Functions Remote Control r ew q t y !2 u !1 i o !0 q STAND-BY button Turn the projector off (p.25). w Wired Remote jack Connect from wireless mouse operation (pp.32-33). the remote control to the projector (p.32). r Laser Light window A laser beam is emitted from here
  • Sanyo PLC-XTC50L | Owners Manual - Page 15
    Remote Control Part Names and Functions @6 !3 @5 !4 @4 !5 @3 !6 @2 !7 @1 !8 @0 !9 @7 For PIN code and blocking.(pp.28,56) @2 KEYSTONE button Correct keystone distortion (p.31). @3 LENS SHIFT button Select the Lens Shift function (p.28). @4 SCREEN button Select the screen size (p.30).
  • Sanyo PLC-XTC50L | Owners Manual - Page 16
    new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared 16.4' (5 m) Remote Receivers) when pressing the
  • Sanyo PLC-XTC50L | Owners Manual - Page 17
    Part Names and Functions Remote Control Code The eight different remote control codes (Code 1-Code 8) are assigned to this projector. Switching the remote control codes prevents interference from other remote controls when several projectors or video equipment next to each other are operated at
  • Sanyo PLC-XTC50L | Owners Manual - Page 18
    up to 3.5 degrees with the adjustable feet. Rotate the adjustable feet and tilt the projector to the proper height; to raise the projector, rotate the both feet clockwise. To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise. To correct keystone distortion
  • Sanyo PLC-XTC50L | Owners Manual - Page 19
    Installation Lens Installation When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the sales dealer for detailed information of the optional lens specifications. Removing the lens 1 Shift the lens to the center position by using the Lens
  • Sanyo PLC-XTC50L | Owners Manual - Page 20
    Installation Connecting to a Computer (Digital and Analog RGB) * Cables used for connection )( =Cables are not supplied with this projector.) • VGA Cable (Mini D-sub 15 pin) (One cable is supplied)* • DVI-Digital Cable * • Serial Control Cable * • BNC Cable * • USB Cable * USB port Monitor
  • Sanyo PLC-XTC50L | Owners Manual - Page 21
    for connection • Video Cable (RCA x 1) • VGA-Scart Cable • S-VIDEO Cable • BNC Cable • DVI-Digital Cable (Cables are not supplied with the projector.) S-video Output Composite Digital Output Video (HDCP RGB Scart Output compatible) 21-pin Output Refer to the Monitor Out Signal Table
  • Sanyo PLC-XTC50L | Owners Manual - Page 22
    to MONITOR OUT terminal. External Audio Equipment Audio Input Audio cable (stereo) AUDIO OUT (stereo) ✔Notes: • When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available. • When the Standby mode is set to "Eco" in the Setting, MONITOR OUT and AUDIO OUT are disabled. (p.54
  • Sanyo PLC-XTC50L | Owners Manual - Page 23
    , consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet does not match your AC outlet, contact your sales dealer. Projector side For the U.S.A. and Canada Ground AC outlet side For Continental
  • Sanyo PLC-XTC50L | Owners Manual - Page 24
    after 20 seconds. Selected Input Source and Lamp Control Lamp control Lamp status See pages 52,63 for the Lamp control and status. ✔Note: • The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. PIN Code Input Dialog Box After the
  • Sanyo PLC-XTC50L | Owners Manual - Page 25
    OR BEFORE THE POWER INDICATOR STOPS BLINKING. OTHERWISE IT WILL RESULT IN SHORTENING THE LAMP LIFE. DO NOT OPERATE THE PROJECTOR CONTINUOUSLY WITHOUT REST. CONTINUOUS USE MAY RESULT IN SHORTENING THE LAMP LIFE. TURN OFF THE PROJECTOR AND LET STAND FOR ABOUT AN HOUR IN EVERY 24 HOURS. "Power off
  • Sanyo PLC-XTC50L | Owners Manual - Page 26
    Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu
  • Sanyo PLC-XTC50L | Owners Manual - Page 27
    menu bar displays changes depending on the input signals. Basic Operation Guide Window Show the selected Menu of the OnScreen Menu. System Select Menu Set the projector's operating configurations (pp.49-59). - Language - Logo - Background - Lamp mode - Lamp control - Filter control - Pointer
  • Sanyo PLC-XTC50L | Owners Manual - Page 28
    Operation Operating with Projector Control Lens Operation The following lens operation can be made with the Lens button on the top control. Press the Lens button to enter each lens operation mode. The selected adjustment display appears on the screen. Zoom ➜ Focus ➜ Lens Shift Zoom Adjustment
  • Sanyo PLC-XTC50L | Owners Manual - Page 29
    Sound Adjustment Direct Operation Volume Press the VOLUME+/- buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE button on the remote control to temporarily turn off the sound. To turn the sound
  • Sanyo PLC-XTC50L | Owners Manual - Page 30
    and the signal being projected through the projector. Remote Control AUTO PC button D.ZOOM button ZOOM buttons FREEZE button INFO. button POINT ed buttons SCREEN button LENS SHIFT button Press the INFO. button on the remote control to display the information window on the screen. To hide
  • Sanyo PLC-XTC50L | Owners Manual - Page 31
    input signal. • "Keystone" disappears after 4 seconds. Reduce the upper width with the Point e button. Reduce the lower width with the Point d button. Reduce the left part with Point 7 button. Reduce the right
  • Sanyo PLC-XTC50L | Owners Manual - Page 32
    on the remote control. Signal Emission Indicator Laser Light Window Pointer Function You can move the Spotlight or Pointer of the projector with the remote control to emphasize a part of the projected image. 1 Press and hold the MENU and SHUTTER buttons for more than 10 seconds to activate the
  • Sanyo PLC-XTC50L | Owners Manual - Page 33
    Operation The remote control can be used as a wireless mouse for your computer. 1 Before operating the wireless mouse, connect your computer and the projector with the supplied USB cable (p. 20). When the Pointer function is used, the wireless mouse is not available. 2 When a USB cable is connected
  • Sanyo PLC-XTC50L | Owners Manual - Page 34
    Input Selection Input Remote Control INPUT buttons Remote Control Operation Press the INPUT 1, INPUT 2, or INPUT 3 buttons on the remote control. The input source appears on the screen as you press each button. Select the connected input source. Top Control INPUT button Top Control Operation
  • Sanyo PLC-XTC50L | Owners Manual - Page 35
    . Video When the RGB video signal is connected. Component* When the component signal is connected. * If the projector cannot reproduce proper video image, select a system manually (see "Video System Selection" on page 36). INPUT 3 Video* When the video signal is connected. S-video* When
  • Sanyo PLC-XTC50L | Owners Manual - Page 36
    system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL
  • Sanyo PLC-XTC50L | Owners Manual - Page 37
    (pp.39-40). ----- There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on page 68.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The adjusted data can be stored in Mode 1-10 (pp.39-40). SVGA
  • Sanyo PLC-XTC50L | Owners Manual - Page 38
    parameters The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by function. When the image is not provided properly with this operation, manual adjustments are required (pp.39-40). • The Auto PC Adjustment
  • Sanyo PLC-XTC50L | Owners Manual - Page 39
    PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen
  • Sanyo PLC-XTC50L | Owners Manual - Page 40
    Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box
  • Sanyo PLC-XTC50L | Owners Manual - Page 41
    Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for graphics. (This icon is displayed with video signal.) Image 1-4 For viewing with the user preset image level in the Image Adjust Menu (see page 44). 41
  • Sanyo PLC-XTC50L | Owners Manual - Page 42
    Image Adjustment Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display
  • Sanyo PLC-XTC50L | Owners Manual - Page 43
    of the following options. Off Disabled. L1 For an active picture. L2 For a still picture. Film For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Image Adjustment ✔Notes: • Progressive cannot be selected when 480p, 575p, or 720p is
  • Sanyo PLC-XTC50L | Owners Manual - Page 44
    Image Adjustment Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Store To store the adjusted data, select Store and press the SELECT button. Use the Point ed buttons
  • Sanyo PLC-XTC50L | Owners Manual - Page 45
    function is set to "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to "On," the picture is left/right reversed. This function is used to project the image from the rear
  • Sanyo PLC-XTC50L | Owners Manual - Page 46
    original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to Provide the full screen image. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the
  • Sanyo PLC-XTC50L | Owners Manual - Page 47
    cannot display any resolution higher than 1600 x 1200. If your computer's screen resolution is higher than that, lower the resolution before connecting to the projector. • The image data other than 1024 x 768 is modified to fit the screen size in initial mode. • True, Full screen, and Digital zoom
  • Sanyo PLC-XTC50L | Owners Manual - Page 48
    the desired function and press the SELECT button. Wide Provide the image at the 16:9 wide screen ratio. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the screen for a few seconds and then the Aspect
  • Sanyo PLC-XTC50L | Owners Manual - Page 49
    Setting Setting This projector has a Setting menu that allows you to set up the other various functions select This function decides on the starting-up display from among following options. User Show the image you captured Default Show the factory-set logo Off Show the countdown display only Logo
  • Sanyo PLC-XTC50L | Owners Manual - Page 50
    projected image. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed the next time you turn on the projector. To cancel the Capture function, select [No]. Capture Select [Yes] to capture the projected image. ✔Notes
  • Sanyo PLC-XTC50L | Owners Manual - Page 51
    code setting can no longer be changed. Background The selected background screen will be displayed when no input signal is detected. Blue Project a blue background User Project an image selected in the Logo setting. Black Project a black background ✔Note: • When no captured image is set, the
  • Sanyo PLC-XTC50L | Owners Manual - Page 52
    • W hen the total lighting time of one lamp exceeds the recommended total hours of use in the Lamp 1/2 mode, the Lamp mode will be switched to Lamp 1 or Lamp 2 mode automatically. • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the
  • Sanyo PLC-XTC50L | Owners Manual - Page 53
    filter is being scrolled. • The filter cannot be rewound. • When the filter is replaced, the total accumulated time of the filter use is automatically set to 0. Pointer You can emphasize a part codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the
  • Sanyo PLC-XTC50L | Owners Manual - Page 54
    of the fluorescent light and so on. Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. If the input signal is interrupted and no button is pressed for
  • Sanyo PLC-XTC50L | Owners Manual - Page 55
    fans will not work properly and that causes malfunctions of the projector and decreases the lamp life. Slant setting +70° Select the projector's installation condition from the following options: UP Off When using the projector within the range of the upward/ downward inclination of ±70º and
  • Sanyo PLC-XTC50L | Owners Manual - Page 56
    the ON / STAND-BY button be pressed in this condition, the projection lamp will be turned on and the SHUTTER indicator turns off. Security (Key wrong with your remote control, contact the dealer where you purchased the projector or the service center. 56 ✔Note: •The Factory default value is set to
  • Sanyo PLC-XTC50L | Owners Manual - Page 57
    and then move the pointer to "Quit" with the Point d button. Press the SELECT button to close the dialog box. PIN code lock When the projector is locked with a PIN code, the PIN code lock symbol appears on the menu bar. Enter a PIN code After a correct PIN code is entered, the
  • Sanyo PLC-XTC50L | Owners Manual - Page 58
    input dialog box appears. Set a new PIN code. Change the PIN code Test pattern Various test pattern are available for use when setting up the projector. caution: when you have changed THE PIn code, write down the new pin code in column of the pin code no. memo on page 82
  • Sanyo PLC-XTC50L | Owners Manual - Page 59
    . •T imer setting notifies that the filter needs replacement.To replace the filter, use the filter control function (p.53). Factory default This function returns all setting values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, and filter counter to the factory default
  • Sanyo PLC-XTC50L | Owners Manual - Page 60
    work properly. It may cause a breakdown. • Make sure that the projection lamps are turned off when you are replacing the filter cartridge. If you replace the filter cartridge when the projection lamps are turned on, the projector will be shut down automatically for safety purposes. • Do not forget
  • Sanyo PLC-XTC50L | Owners Manual - Page 61
    cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Replacement filter cartridge can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector PLC-XTC50L ● Replacement Filter Cartridge Type No. : POA-FIL-100 (Service Parts Code: 610
  • Sanyo PLC-XTC50L | Owners Manual - Page 62
    . Select [Yes] to continue. 4 Another confirmation dialog box appears, select [Yes] to reset the Filter counter. Resetting the Scroll Counter Be sure to reset the Scroll counter after replacing the filter cartridge. 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons
  • Sanyo PLC-XTC50L | Owners Manual - Page 63
    reaches the recommended total hours of use. Check the number of lamp on the Lamp Status Display or the LAMP 1/2 REPLACE indicators and replace the lamp. Lamp Status Display The Lamp Status Display appears on screen when the projector is turned on or the input position (input 1, input 2, or Input
  • Sanyo PLC-XTC50L | Owners Manual - Page 64
    medical advice immediately. Follow these steps to replace the lamp. 1 Check the number of lamp to be replaced on the Lamp Status Display or the LAMP 1/2 REPLACE indicators and replace the lamp. 2 Turn off the projector and unplug the AC power cord. Let the projector cool for at least 45 minutes
  • Sanyo PLC-XTC50L | Owners Manual - Page 65
    the following information to the dealer. ● Model No. of your projector : PLC-XTC50L ● Replacement Lamp Type No. : POA-LMP125 (Service Parts No. 610 342 2626) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result
  • Sanyo PLC-XTC50L | Owners Manual - Page 66
    of the projector away from the duct or vent. - Is the filter clean? Clean the filter periodically or replace it with a new one. The projector is shut red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL
  • Sanyo PLC-XTC50L | Owners Manual - Page 67
    , solvents, or other harsh chemicals might scratch the surface of the lens. When the projector is not in use, replace the lens cap. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning. Gently wipe the projector body with a soft dry cleaning cloth. When the cabinet is heavily
  • Sanyo PLC-XTC50L | Owners Manual - Page 68
    Lamp replacement icon or the Filter warning icon. Lamp control or lamp status icon See pages 59,64. appears. No image - Check the connection between your computer or video equipment and the projector to the projector See your computer's instruction manual for the
  • Sanyo PLC-XTC50L | Owners Manual - Page 69
    LAMP 1/2 REPLACE indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See pages 63-65, 74. - Check the Lamp is distorted. - With maximum lens shift, image distortion may AUDIO OUT is plugged in, the projector's built-in speaker is not
  • Sanyo PLC-XTC50L | Owners Manual - Page 70
    lock. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the
  • Sanyo PLC-XTC50L | Owners Manual - Page 71
    Image 1 Image 2 Image 3 Image 4 Quit Information Input H-sync freq. V-sync freq. Screen Language Lamp mode Lamp control Lamp 1 Lamp 2 Filter counter Power management Shutter management Remote control Projector ( ) Min Security Remote control SERIAL NO. Key lock PIN code lock ✔Note: • The Menu
  • Sanyo PLC-XTC50L | Owners Manual - Page 72
    /User/Black Lamp mode Lamp control Lamp 1/Lamp 2 Lamp 1 / 2 Quit Lamp control Auto 1/Auto 2/High /Normal/Eco 1/Eco 2 Lamp life control Filter Projector Management On/Off 5 - 180 Min. Quit Security Key lock Off Projector (all) Projector (part) Remote control (all) Remote control (part)
  • Sanyo PLC-XTC50L | Owners Manual - Page 73
    mode. The projection lamp is being cooled down in the Shutter ✽ management mode. The projector is in the Shutter management mode. Press ✽ the ON/STAND-BY button to turn on the projector. ✽ ✽ ✽ ✽ Fig.1 Filter replacement icon and "Please wait..." The filter is scrolled using the
  • Sanyo PLC-XTC50L | Owners Manual - Page 74
    returns to normal. When turning on the projector, the WARNING TEMP. indicator stops blinking. Check and replace the filter. ✽ ✽✽ red The lamp cannot light up. (The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is
  • Sanyo PLC-XTC50L | Owners Manual - Page 75
    WARNING TEMP. red WARNING FILTER orange SHUTTER blue LAMP 1/2 REP. yellow Projector Condition ✽ ✽ ✽ Fig.2 Filter replacement icon Fig.3 Fig.4 Filter cartridge replacement icon ✽ If the Filter counter reached a time set in the timer setting, a Filter replacement icon (Fig.2) appears on
  • Sanyo PLC-XTC50L | Owners Manual - Page 76
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below and less than 140 MHz of Dot Clock. PC Adjustment is limited
  • Sanyo PLC-XTC50L | Owners Manual - Page 77
    Appendix When an input signal is digital from the DVI terminal, refer to the chart below. PC Adjust Menu cannot be selected when Input 1 [RGB (PC digital)] is selected in the Input Menu. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 RESOLUTION
  • Sanyo PLC-XTC50L | Owners Manual - Page 78
    Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Panel Resolution LCD Panel System Panel Resolution Number of Pixels Signal Compatibility Color System High Definition TV Signal Scanning Frequency Optical Information Projection Lens Projection Lamp
  • Sanyo PLC-XTC50L | Owners Manual - Page 79
    Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable USB Cable Lens Mount Cover PIN Code Label Lens Antitheft Screw * * Contact the dealer where you purchased the projector or the service center about the Lens Antitheft Screw. ● The
  • Sanyo PLC-XTC50L | Owners Manual - Page 80
    Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input Input 1 RGB (PC analog) RGB (Scart) RGB (PC digital) RGB (AV
  • Sanyo PLC-XTC50L | Owners Manual - Page 81
    Appendix Configurations of Terminals INPUT 1/ANALOG OUT Terminal: Analog RGB (Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 Input 1 Red Input 2 Green Input 3 Blue Input 4 No Connect 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) Output 1 Red Output 2 Green Output
  • Sanyo PLC-XTC50L | Owners Manual - Page 82
    Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo PLC-XTC50L | Owners Manual - Page 83
    Dimensions Unit: inch (mm) 15.59 (396.0) 17.76 (451.0) Appendix 21.66 (550.1) 3.5˃MAX 3.44 (87.3) 3.70 (94.0) (PANEL CENTER) 3.94 (100.0) 3.94 (100.0) 6.89 (175.0) 3.15 (80.0) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) 10.85 (275.5) 5.55 (141.0) 5.55 (141.0) 83
  • Sanyo PLC-XTC50L | Owners Manual - Page 84
    KH7AL SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
*Projection lens is optional.
Multimedia Projector
MODEL
PLC-XTC50L
Owner’s Manual