Sanyo PLC-XU111 Owners Manual

Sanyo PLC-XU111 - XGA LCD Projector Manual

Get Sanyo PLC-XU111 - XGA LCD Projector PDF manuals and user guides
UPC - 086483067914
View all Sanyo PLC-XU111 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XU111 manual content summary:

  • Sanyo PLC-XU111 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-XU111 PLC-XU111K Network Supported ❏ Wireless LAN IEEE802.11b/g ❏ Wired LAN 100-Base-TX/10-Base-T Memory Viewer ❏ USB Memory Viewer (optionally available) Compatible with a dedicated USB memory ✽Refer to the owner's manuals below for details about network and memory
  • Sanyo PLC-XU111 | Owners Manual - Page 2
    2
  • Sanyo PLC-XU111 | Owners Manual - Page 3
    network. For details, refer to the owner's manual "Network Set-up and Operation." ◆ Lamp Control Brightness of the projection lamp can be selected (pp.28, 53). ◆ Quick Termination The AC power cord can be unplugged immediately after turning off the projector without waiting for the termination of
  • Sanyo PLC-XU111 | Owners Manual - Page 4
    of Contents 4 To the Owner 5 Safety Instructions 6 Air Circulation 7 Moving the Projector 7 Installing the Projector in Proper Directions 8 Compliance 9 Part Names and Functions 10 Front 10 Back 10 Bottom 10 Rear Terminal 11 Top Control 12 Remote Control 13 Laser Pointer
  • Sanyo PLC-XU111 | Owners Manual - Page 5
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC
  • Sanyo PLC-XU111 | Owners Manual - Page 6
    has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by
  • Sanyo PLC-XU111 | Owners Manual - Page 7
    Safety Instructions Air Circulation Openings in the cabinet are provided for from external forces. Do not transport the projector by courier or any other transport service with this case, otherwise the projector can be damaged. When handling the projector, do not drop, bump, subject it to
  • Sanyo PLC-XU111 | Owners Manual - Page 8
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the
  • Sanyo PLC-XU111 | Owners Manual - Page 9
    which can be determined by turning the equipment off and on, the user is encouraged to try to instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number(s) Trade Name Responsible party Address : PLC-XU111 : Sanyo : SANYO
  • Sanyo PLC-XU111 | Owners Manual - Page 10
    q Zoom Ring w Infrared Remote Receiver e Focus Ring r Projection Lens t Slide Shutter Lever y Top Controls and Indicators u Exhaust Vent Lamp Cover !5 Air Filter !6 Adjustable Feet !7 Battery Cover ✽ Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector
  • Sanyo PLC-XU111 | Owners Manual - Page 11
    and use the PAGE ed buttons on the remote control during a presentation, connect the USB port of the computer to the USB terminal with a USB cable (not supplied) (pp.13, 19). e SERVICE PORT This jack is used to service the projector. r COMPUTER IN 2/COMPONENT IN Connect the computer or component
  • Sanyo PLC-XU111 | Owners Manual - Page 12
    and Functions Top Control q w i e o r !0 t !1 y u q ALARM indicator Blinks red when informing the setting or battery status (pp.58-59). w LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.65, 71). e ON/STAND-BY button Turn the projector on or off
  • Sanyo PLC-XU111 | Owners Manual - Page 13
    button Turn the projector on or off (pp.22-23). e WIRED REMOTE jack Connect the remote control cable (not supplied) to this jack when using as a wired remote control. r viewer input. See the owner's manual "Network Set-up and Operation" and owner's manual of Memory viewer (optionally available). 13
  • Sanyo PLC-XU111 | Owners Manual - Page 14
    Pointer function.) 2 Press the LASER button on the remote control pointing toward the projector. The Spotlight or Pointer is displayed on the screen screen, press the LASER button pointing toward the projector and see if the LASER button lighting is turned off. To switch to the Laser pointer again,
  • Sanyo PLC-XU111 | Owners Manual - Page 15
    connected to the computer and the projector, turn on the projector first, then the computer. If you turn on the computer first, the wireless the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on
  • Sanyo PLC-XU111 | Owners Manual - Page 16
    by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about 16.4' (5 m) and 60 degrees in
  • Sanyo PLC-XU111 | Owners Manual - Page 17
    Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. ✔Notes: •The brightness in the room has a great influence on picture quality. It is recommended
  • Sanyo PLC-XU111 | Owners Manual - Page 18
    power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION For safety, unplug the AC power cord when the projector is not in use. When the projector is connected to an outlet with the AC power
  • Sanyo PLC-XU111 | Owners Manual - Page 19
    -in speaker is disconnected. •USB cable connection is needed when operating the computer with the remote control or using the PAGE ed buttons on the remote control. AUDIO OUT (stereo) Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. 19
  • Sanyo PLC-XU111 | Owners Manual - Page 20
    Input AUDIO IN VIDEO S-VIDEO Audio cable (stereo) AUDIO OUT (stereo) ✔Notes: •When connecting the AUDIO OUT to external audio equipment, the projector's built-in speaker is disconnected. •The S-VIDEO jack connection overrides the VIDEO jack connection when selecting AUTO in the Input Menu (p.40
  • Sanyo PLC-XU111 | Owners Manual - Page 21
    IN AUDIO IN External Audio Equipment Audio Input Audio cable (stereo) ✔Notes: •When connecting the AUDIO OUT to external audio equipment, the projector's built-in speaker is disconnected. •See page 75 for ordering optional cables. •RGB Scart signal cannot be output from the MONITOR OUT terminal
  • Sanyo PLC-XU111 | Owners Manual - Page 22
    of this manual and keep it at hand. Should the PIN code be missing or forgotten, consult your dealer or service center. 22 16 The preparation display will disappear after 30 seconds. Selected Input Source and Lamp Control Lamp control status (See page 53 for Lamp control status.) ✔Note: •The Filter
  • Sanyo PLC-XU111 | Owners Manual - Page 23
    the top control or on the remote control, and "Power off?" appears on the screen. 2 Press the ON/STAND-BY button again to turn off the projector. The DO NOT OPERATE THE PROJECTOR CONTINUOUSLY WITHOUT REST. CONTINUOUS USE MAY RESULT IN SHORTENING THE LAMP LIFE. TURN OFF THE PROJECTOR AND LET STAND FOR
  • Sanyo PLC-XU111 | Owners Manual - Page 24
    How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu. 2 Use the
  • Sanyo PLC-XU111 | Owners Manual - Page 25
    pages 69-70. For computer source Guide Window Show the selected Menu of the size of Used to set the the image [Normal/ projector's operating True/Wide/Full configurations (pp.47- screen/ ). Sound Menu Wired Menu Used to adjust See owner's manual the volume or "Network Setup mute the sound and
  • Sanyo PLC-XU111 | Owners Manual - Page 26
    has keystone distortion after pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control, correct the image manually as follows: Press the KEYSTONE button on the top control or on the remote control. The Keystone dialog box appears. Use the Point ed buttons to
  • Sanyo PLC-XU111 | Owners Manual - Page 27
    to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE button on the remote control to temporarily turn off the sound. To turn the sound back on, press the MUTE button again or press the VOLUME +/- buttons. The Mute function is also effective for the
  • Sanyo PLC-XU111 | Owners Manual - Page 28
    owner's manual "Network Set-up and Operation" for details about the network input. Remote Control AUTO PC button COMPUTER/VIDEO/ NETWORK button FREEZE button Press the FREEZE button on the remote control Lower brightness reduces the lamp power consumption and extends the lamp life. ✔Note: •See
  • Sanyo PLC-XU111 | Owners Manual - Page 29
    Basic Operation NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the Logo selection (see page 49), the screen changes each
  • Sanyo PLC-XU111 | Owners Manual - Page 30
    the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input Memory viewer are for the Network function. See owner's manual "Network Set-up and Operation" and owner's manual of Memory viewer (optionally available). •When the
  • Sanyo PLC-XU111 | Owners Manual - Page 31
    top control or press the COMPUTER button on the remote control. controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. •Wired, Wireless, Memory viewer are for the Network function. See owner's manual
  • Sanyo PLC-XU111 | Owners Manual - Page 32
    (pp.34-35). ----- There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on page 67.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The adjusted data can be stored in Mode 1-5 (pp.34-35). SVGA 1 PC
  • Sanyo PLC-XU111 | Owners Manual - Page 33
    the AUTO PC button on the remote control. Remote Control AUTO PC button Menu Operation Auto PC the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can is not provided properly with this operation, manual adjustments are required (pp.34-35). •
  • Sanyo PLC-XU111 | Owners Manual - Page 34
    enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Use the
  • Sanyo PLC-XU111 | Owners Manual - Page 35
    Input Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box
  • Sanyo PLC-XU111 | Owners Manual - Page 36
    on the projector. Real Picture mode with improved halftone for graphics. Blackboard(Green) For the image projected on a blackboard. See above for further description. Image 1~4 For viewing with the user preset image mode in the Image Adjust Menu (see page 37-38). 36 Remote Control IMAGE button
  • Sanyo PLC-XU111 | Owners Manual - Page 37
    Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the adjustment
  • Sanyo PLC-XU111 | Owners Manual - Page 38
    When the original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to pan the image. When adjusted, the arrows will turn red. When reached to the correction limits, the arrows will disappear. Wide Provide the
  • Sanyo PLC-XU111 | Owners Manual - Page 39
    Input Custom Adjust the screen scale and position manually with this function. Press the SELECT button at size. A projected image can be also expanded by pressing the D.ZOOM e button on the remote control. Digital zoom - Select Digital zoom -. The On-Screen Menu disappears and "D. zoom -" appears
  • Sanyo PLC-XU111 | Owners Manual - Page 40
    as described below. Top Control Remote Control INPUT button INPUT button projector automatically detects incoming video signal, and adjusts itself to optimize its performance. The projector Network function. See the owner's manual "Network Set-up and Operation" and owner's manual of Memory viewer (
  • Sanyo PLC-XU111 | Owners Manual - Page 41
    the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct , Memory viewer are for the Network function. See owner's manual "Network Set-up and Operation" and owner's manual of Memory viewer (optionally available). •When the Input
  • Sanyo PLC-XU111 | Owners Manual - Page 42
    detects an incoming video signal, and adjusts itself to optimize its performance. COMPONENT VIDEO SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i. AV System Menu (Video
  • Sanyo PLC-XU111 | Owners Manual - Page 43
    mode preset on the projector. Cinema Picture mode adjusted with fine tone. Blackboard(Green) For the image projected on a blackboard. See above for further description. Image1-4 For viewing with the user preset image mode in the Image Adjust Menu (see page 44-45). Remote Control IMAGE button IMAGE
  • Sanyo PLC-XU111 | Owners Manual - Page 44
    Video Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the
  • Sanyo PLC-XU111 | Owners Manual - Page 45
    options. Off.......... Disabled. L1........... For an active picture. L2........... For a still picture. Film ........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT
  • Sanyo PLC-XU111 | Owners Manual - Page 46
    Video Input Screen Size Adjustment This projector has the picture screen resize function, which Wide Provide the image at the 16:9 wide screen ratio. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the
  • Sanyo PLC-XU111 | Owners Manual - Page 47
    Keystone Auto . . . . . Always works and corrects keystone distortion according to the projector's tilt. Manual . . .Works only when pressing the AUTO SET button on the remote control or the AUTO SETUP button on the top control. Off Disables Auto Keystone. ✔Notes: •Auto PC Adj. and Auto Keystone
  • Sanyo PLC-XU111 | Owners Manual - Page 48
    is in this option. Countdown Off ........ Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Hide the On-Screen Displays except; ●On-Screen Menu ●"Power
  • Sanyo PLC-XU111 | Owners Manual - Page 49
    capture the projected image. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed the next time you turn on the projector or when you press the NO SHOW button (see page 29). To cancel the Capture function, select [No
  • Sanyo PLC-XU111 | Owners Manual - Page 50
    number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, "Logo PIN code" and the number will turn red for a moment. Enter the correct Logo PIN code all over again. Change the Logo PIN code
  • Sanyo PLC-XU111 | Owners Manual - Page 51
    When pressing the COMPUTER button or VIDEO button on the remote control. On2 ........ Input search works under the following situation. - When turning on the projector by pressing the ON/STAND-BY button on the top control or the remote control. - When pressing the COMPUTER button or VIDEO button on
  • Sanyo PLC-XU111 | Owners Manual - Page 52
    to the owner's manual "Network Setup and Operation." ✔Note: •When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management For reducing power consumption as well as maintaining the lamp life, the Power
  • Sanyo PLC-XU111 | Owners Manual - Page 53
    AC power cord to a wall outlet. ✔Note: •Be sure to turn off the projector properly (see "Turning Off the Projector" on page 23). If the projector is turned off in the incorrect sequence, the On start function does not work properly. Lamp control This function allows you to change brightness of the
  • Sanyo PLC-XU111 | Owners Manual - Page 54
    operation of the remote control. To unlock, use the top control. If the top control accidentally becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Key lock
  • Sanyo PLC-XU111 | Owners Manual - Page 55
    you can start to operate the projector. If you entered an incorrect PIN code, "PIN code" and the number will turn red for a moment. Enter PROJECTOR CAN NO LONGER BE STARTED. Change the PIN code Alarm This function allows you to configure the Alarm operation. See "How to Use the Antitheft Alarm
  • Sanyo PLC-XU111 | Owners Manual - Page 56
    method. Otherwise, the cooling fans will not work properly and that causes malfunctions of the projector and decreases the lamp life. Be sure to set the Fan control in MAX in the setting menu when the projector is inclined between +40 degrees to +140 degrees to the horizontal plane. Warning log This
  • Sanyo PLC-XU111 | Owners Manual - Page 57
    300H) depending on the use environment. Factory default This function returns all setting values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, Antitheft alarm function when it is set on and filter counter to the factory default settings. Quit Exit the Setting Menu. Fig
  • Sanyo PLC-XU111 | Owners Manual - Page 58
    to turn the alarm function on. The ALARM indicator blinks for a few seconds and the projector enters the warning mode. (If the battery is not charged enough for the alarm function to operate normally, it bleeps and the Alarm indicator will blink red every 20 seconds.) Top Control ALARM indicator
  • Sanyo PLC-XU111 | Owners Manual - Page 59
    ALARM indicator is turned battery life. CAUTION: WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN THE NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO ON PAGE 78, AND KEEP IT SECURELY. IF YOU FORGET YOUR PIN CODE, SOME SETTINGS OF THE ANTITHEFT ALARM FUNCTION CAN NO LONGER BE CHANGED. Top Control ALARM
  • Sanyo PLC-XU111 | Owners Manual - Page 60
    "Off" when not using the Alarm function. This can save the power and battery life. Replace the rechargeable batteries Use only the specified battery for this projector. Using other types of battery may cause accident or fire hazard. Replacement Battery: SANYO Ni-MH BATTERY PACK Part No. 645 089 8587
  • Sanyo PLC-XU111 | Owners Manual - Page 61
    out of this range may result in fluid leak, heat generation, or shortening battery life. ● If you do not use the projector or the Antitheft alarm function for a long period of time, remove the battery from the projector and store it in a place where the temperature is always between -4˚F to 86
  • Sanyo PLC-XU111 | Owners Manual - Page 62
    . If the projector cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Control WARNING
  • Sanyo PLC-XU111 | Owners Manual - Page 63
    and may result in internal heat buildup and adversely affect the life of the projector. If a "Filter warning" icon appears on the screen, clean the filter immediately. Clean the filter by following the steps below. 1 Turn off the projector, and unplug the AC power cord from the AC outlet
  • Sanyo PLC-XU111 | Owners Manual - Page 64
    of the lens against scratches and dirt. When you are not using the projector, close the Slide Shutter. To open or close, use the Slide Shutter on the top of the cabinet. Do not close the shutter when the projection lamp is on. Cleaning the Projection Lens Unplug the AC power cord before cleaning.
  • Sanyo PLC-XU111 | Owners Manual - Page 65
    Handle Screw Screw Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XU111/PLC-XU111K : POA-LMP111 (Service Parts No. 610
  • Sanyo PLC-XU111 | Owners Manual - Page 66
    up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as
  • Sanyo PLC-XU111 | Owners Manual - Page 67
    is turned on. -When the projector does not project an image from the connected computer, restart the computer. Problem: No power Image is out of focus. No projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector
  • Sanyo PLC-XU111 | Owners Manual - Page 68
    . Try to set the Alarm setting again. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model
  • Sanyo PLC-XU111 | Owners Manual - Page 69
    (1) Go to System (2) N/A Go to System (3) Go to System (3) Go to System (3) See owner's manual "Network Setup and Operation." See owner's manual "Network Setup and Operation." See owner's manual of Memory viewer (optionally available) N/A ........not applicable The menu will be displayed when
  • Sanyo PLC-XU111 | Owners Manual - Page 70
    Spotlight/Pointer Quit Remote control Code 1-Code 8 Security Key lock Off Projector Remote control Quit PIN code lock Off/On1/On2 PIN code change Quit Fan Fan control Warning log Lamp counter Filter counter Factory default Quit Alarm Off Battery charge Alarm volume Sensitivity Ringing
  • Sanyo PLC-XU111 | Owners Manual - Page 71
    clean the air filter. The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on the ✽ projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center for service and checkup
  • Sanyo PLC-XU111 | Owners Manual - Page 72
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock for analog signal and 110
  • Sanyo PLC-XU111 | Owners Manual - Page 73
    Appendix When the input signal is digital from DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 9 RESOLUTION 640 x 480 640 x 480 768 x 575 800 x 600 1024 x 768 1366 x 768 1360 x 768
  • Sanyo PLC-XU111 | Owners Manual - Page 74
    Projection Lamp Adjustable from 33" to 300" 4.3'-32.8' (1.3 m-10.0 m) F1.7-2.1 lens with f26.7 mm-32.0 mm with manual zoom and focus 275 41˚F-95˚F (5 ˚C-35 ˚C) 14˚F-140˚F (-10˚C-60 ˚C) Remote Control Battery Operating Range Dimensions Net Weight Laser Pointer AAA or LR03 Type x 2 16.4' (5 m)/±30
  • Sanyo PLC-XU111 | Owners Manual - Page 75
    Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label Alarm Label Network Application (CD-ROM) Soft Carrying Case USB Wireless LAN Adapter ● The specifications are subject to change without notice. ● LCD panels are
  • Sanyo PLC-XU111 | Owners Manual - Page 76
    Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer1 (Analog) Computer1
  • Sanyo PLC-XU111 | Owners Manual - Page 77
    CONNECTOR (Series B) 1 Vcc 21 2 - Data 3 + Data 34 4 Ground LAN TERMINAL 1 TX + 5 ----- 2 TX - 6 RX - 3 RX + 7 ----- 4 ----- 8 ----- 87654321 SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN 876 5 43 21 1 R X D 5 RTS/CTS 2 ----- 6 TXD 3 ----- 7 GND 4 GND 8 GND
  • Sanyo PLC-XU111 | Owners Manual - Page 78
    keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* Alarm
  • Sanyo PLC-XU111 | Owners Manual - Page 79
    Dimensions 13.15 (334) 3.17 (80.5) 2.14 (54.3) 8.9º MAX 9.13 (232) 2.78 (70.5) 3.66 (93) Appendix Unit: inch (mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.472 (12.0) 5.20 (132) 5.51 (140) 5.08 (129) 4.43 (112.5) 79
  • Sanyo PLC-XU111 | Owners Manual - Page 80
    KM6AC SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Multimedia Projector
MODEL
PLC-XU111
PLC-XU111K
Owner’s Manual
Netw
or
k Suppor
t
ed
❏
Wireless LAN
IEEE802.11b/g
❏
Wired LAN
100-Base-TX/10-Base-T
Memory V
iew
er
❏
USB Memory Viewer (optionally available)
Compatible with a dedicated USB memory
✽
Refer to the owner’s manuals below for details about
network and memory viewer function.
■
Network Set-up and Operation
■
Owner's Manual
USB Memory
This manual is provided with optionally supplied
USB memory.