Sanyo PLC XU115 Instruction Manual, PLC-XU115

Sanyo PLC XU115 - XGA LCD Projector Manual

Sanyo PLC XU115 manual content summary:

  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 1
    Multimedia Projector MODEL PLC-XU115 Network Supported □ Wireless LAN IEEE802.11b/g □ Wired LAN 100-Base-TX/10-Base-T Memory Viewer □ SD Card Memory Viewer * Refer to the owner's manuals below for details about network and memory viewer function. ■ Network Set-up and Operation ■ Memory viewer
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 2
    
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 3
    function reduces power consumption and maintains the lamp life (p.52). ◆ Lamp Control Brightness of the projection lamp can be selected (pp.28, 53). ◆ Quick Termination ◆ Memory Viewer Function Insert the dedicated SD card memory into the projector to project images or presentation data stored
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 4
    and Cleaning 58 Warning Indicator 58 Cleaning the Filter 59 Resetting the Filter Counter 59 Attaching the Lens Cap 60 Cleaning the Projection Lens 60 Cleaning the Projector Cabinet 60 Lamp Replacement 61 Resetting the Lamp Counter 62 Appendix 63 Troubleshooting 63 Menu Tree
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 5
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 6
    cloth for cleaning. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 7
    Safety Instructions Air Circulation Openings in the cabinet are provided for from external forces. Do not transport the projector by courier or any other transport service with this case, otherwise the projector can be damaged. When handling the projector, do not drop, bump, subject it to
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 8
    Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 9
    instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number PLC-XU115 Trade Name : Sanyo Responsible party : SANYO from the Parts Department indicated in your User Instructions. If the plug supplied is not
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 10
    Connectors ⑬ Power Cord Connector ⑭ SD Card Slot ⑮ LAN Connection Terminal ⑯ Lamp Cover ⑰ Filters ⑱ Adjustable Feet Note: ② WIRELESS Indicator and ⑮ LAN Connection Terminal are for the Network function. Refer to the owner's manual "Network Set-up and Operation". ⑭ SD Card Slot is for the Memory
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 11
    the computer with the remote control and use the PAGE ▲▼ buttons on the remote control during a presentation, connect the USB port of the computer to the USB terminal with a USB cable (not supplied) (pp.13, 19). ③ SERVICE PORT This jack is used to service the projector. ④ COMPUTER IN 2/COMPONENT IN
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 12
    Top Control ① ⑦ ② ⑧ ③ ⑨ ④ ⑩ ⑤ ⑥ ① LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.61, 69). ② ON/STAND-BY button Turn the projector on or off (pp.22-23). ③ INPUT button Select an input source (pp.30-31, 40-41). ④ KEYSTONE button ⑦ WARNING
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 13
    ) ㉔ PRESENTATION POINTER button Move a pointer of the projector or a pointer for wireless mouse operation. (pp.14-15) ㉕ AUTO SET/CANCEL button - Correct vertical keystone distortion and adjust the PC display parameters. (pp.26 47) - Display the image in SD card or return to the menu bar in
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 14
    to activate the Pointer function. (The Laser pointer has switched to the Pointer function.) 2 Press the LASER button on the remote control pointing toward the projector. The Spotlight or Pointer is displayed on the screen with the LASER button lighting green. Then move the Spotlight or Pointer with
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 15
    Mouse Operation The remote control can be used as a wireless mouse for your computer. 1 Before operating the wireless mouse, connect your computer and the projector with a USB cable (not supplied). See "Connecting to a Computer" on page 19. When the Pointer function is used, the wireless mouse is
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 16
    the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 17
    the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. Notes: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 18
    service station. Connect the projector with all peripheral equipment before turning the projector on. Connect the AC power cord (supplied) to the projector cord does not match your AC outlet, contact your sales dealer. Projector side AC outlet side For the U.S.A. and Canada For Continental Europe For
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 19
    is not available. • USB cable connection is needed when operating the computer with the remote control or using the PAGE ▲▼ buttons on the remote control. AUDIO OUT SD (stereo) Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. 19
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 20
    S-video cable External Audio Equipment Audio Input VIDEO AUDIO IN S-VIDEO Audio cable (stereo) KB3AC SD AUDIO OUT (stereo) Notes: • When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available. • The S-VIDEO jack connection overrides the VIDEO jack connection when
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 21
    IN 2/COMPONENT IN COMPUTER/ COMPONENT AUDIO IN External Audio Equipment Audio Input Audio cable (stereo) KB3AC SD AUDIO OUT (stereo) Notes: • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • See page 73 for ordering optional cables. • RGB Scart signal
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 22
    will disappear after 30 seconds. Selected Input Source and Lamp Control Lamp control status (See page 53 for Lamp control status.) Note: • The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. PIN Code Input Dialog Box After the OK
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 23
    changed according to the temperature inside the projector. • Do not put the projector in a case before the projector is cooled enough. • If the WARNING indicator blinks or lights red, see "Warning Indicators" on page 58. • While the POWER indicator is blinking, the lamp is being cooled down and the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 24
    How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu. 2 Use the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 25
    Tree" on pages 67-68. Basic Operation For computer source Guide Window Show the selected Menu of the OnScreen Menu. PC System the projector's T r u e / W i d e / F u l l / operating Custom/Digital zoom configurations +/-] (pp.38-39). (pp.47-57). Wireless Menu See owner's manual "Network
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 26
    correct Keystone distortion according to the projector's tilt and adjust the computer display parameters (Fine sync, Total dots, and Picture position) by just pressing the AUTO SETUP/CANCEL button on the top control or the AUTO SET/CANCEL button on the remote control. The operational setup for the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 27
    on, press the MUTE button again or press the VOLUME +/- buttons. The Mute function is also effective for the AUDIO OUT jack. Top Control Remote Control VOLUME+/buttons POINT▲button VOL- (◄) button VOL+ (►) button POINT▼button Menu Operation 1 Press the MENU button to display the On-Screen Menu
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 28
    remote control to enter to the Digital zoom +/- mode. See page 39 for details. LAMP CONTROL button Press the LAMP CONTROL button on the remote control to select the lamp Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Note: • See the next page
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 29
    NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the Logo selection (p.49), the screen changes each time you press the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 30
    correct input source should be selected through Menu operation as described below. Top Control INPUT button Computer 1 (Analog) Computer 1 (Digital) Computer 2 Video Wired Remote Control Wireless COMPUTER button Computer 1 (Analog) Computer 1 (Digital) Menu Operation 1 Press the MENU button
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 31
    Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. • Wired and Wireless are for the Network function. See owner
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 32
    XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector Check the connection between your computer and the projector. (See "Troubleshooting" on page 63.) The preset system is manually adjusted in the PC Adjust Menu. The
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 33
    be operated directly by pressing the AUTO PC button on the remote control. Remote Control AUTO PC button Menu Operation Auto PC Adj. 1 Press the The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 34
    enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Use the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 35
    Input Display area H Use the Point ◄► buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point ◄► buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 36
    preset on the projector. Real Picture mode with improved halftone for graphics. Blackboard(Green) For the image projected on a blackboard. See above for further description. Image 1~4 For viewing with the user preset image mode in the Image Adjust Menu (pp. 37-38). 36 Remote Control IMAGE button
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 37
    Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄►buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ▲▼ buttons to move the red frame pointer to the desired item and then press the SELECT button to display the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 38
    the screen size. True Provide the image in its original size. When the original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically. Use the Point buttons to pan the image. When adjusted, the arrows will turn red. When reached to the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 39
    only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM + button on the remote control. Digital zoom - Select Digital zoom -. The On-Screen Menu disappears and "D. zoom -" appears. Press the SELECT button to compress image size. The projected
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 40
    , the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. The projector selects connection (p.51). Top Control Remote Control INPUT button INPUT button Computer 1 (Analog) Computer 1 (Digital) Computer 2 Video Wired Wireless VIDEO button Input
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 41
    the Source Select Menu appeared for Computer 2, move the pointer to Component or RGB(Scart) and then press the SELECT button. Remote Control wireless COMPUTER button Computer 1 (Analog) Input Menu Computer 1 (Digital) Computer  Input Menu icon Component When the input source is coming from
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 42
    itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. AV
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 43
    button on the remote control. Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Cinema Picture mode a blackboard. See above for further description. Image1-4 For viewing with the user preset image mode in the Image Adjust Menu (pp. 44-45). Image
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 44
    Video Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄► buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ▲▼ buttons to move the red frame pointer to the desired item and then press the SELECT button to display the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 45
    options. Off.......... Disabled. L1........... For an active picture. L2........... For a still picture. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 46
    Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables the image at the 16:9 wide screen ratio. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 47
    Auto. . . . . . Always works and corrects keystone distortion according to the projector's tilt. Manual . . . Works only when pressing the AUTO SET/ CANCEL button on the remote control or the AUTO SETUP/CANCEL button on the top control. Off Disables Auto Keystone. Notes: • Auto PC Adj. and Auto
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 48
    this option. Countdown Off......... Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Hide the On-Screen Displays except; ● On-Screen Menu ● "Power off
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 49
    the projected image. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed the next time you turn on the projector or when you press the NO SHOW button (p.29). To cancel the Capture function, select [No]. Notes: • Before
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 50
    -digit number. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, "Logo PIN code" and the number will turn red for a moment. Enter the correct Logo PIN code
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 51
    is used to project the image from a ceiling-mounted projector. Ceiling Rear When this function is set to " remote control. On2........ Input search works under the following situation. - When turning on the projector by pressing the POWER ON/STAND-BY button on the top control or the remote control
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 52
    the owner's manual "Network Set-up and Operation". Note: • When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management For reducing power consumption as well as maintaining the lamp life, the Power
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 53
    or Small) or a pattern of the Pointer (Arrow, Finger, or Dot). See "Pointer Function" on page 14. Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 54
    the operation of the remote control. To unlock, use the top control. If the top control accidentally becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. On
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 55
    -digit number. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, "PIN code" and the number will turn red for a moment. Enter the correct PIN code all over again
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 56
    On 3....Be sure to set the Lamp control in High and the Fan control in On 3 when using the projector inclined at between +40 degrees to warning log records will be deleted. Lamp counter This function is used to reset the lamp counter. When the lamp life is left less than 100 hours, the Lamp
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 57
    a set time. Note: • This icon also appears at turning on. Fig.4 Filter warning icon Factory default This function returns all setting values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, and filter counter to the factory default settings. Quit Exit the Setting Menu
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 58
    Is the filter clean? Clean the filter periodically. The projector is shut down and the WARNING indicator lights red. When the projector detects an abnormal condition, it is automatically shut down to protect the inside of the projector and the WARNING indicator lights red. In this case, unplug the
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 59
    and may result in internal heat buildup and adversely affect the life of the projector. If a "Filter warning" icon appears on the screen, clean the filters immediately. Clean the filter by following the steps below. 1 Turn off the projector, and unplug the AC power cord from the AC outlet. 2 Turn
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 60
    amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet. When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. Lens Cap Hole String for the lens cap Secure it to the hole
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 61
    . Handle Screw Screw Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XU115 : POA-LMP111 (Service Parts No
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 62
    a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 63
    than Input mode or - That is the Lamp replacement icon or the Filter warning icon. See Lamp mode icon appears. page 56 or 57. Image is out of focus. - Adjust focus of the projector. See page 26. - Provide proper distance between the projector and the projection screen. See page 17. - Check
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 64
    for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 cannot be displayed. Press the NO SHOW button or any other button on the remote control. No sound - Check the audio cable connection from audio input source. -
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 65
    . - Make sure the mouse driver is installed on your computer, otherwise, the remote control can not be used as a wireless mouse. - Make sure the signal is from the computer, otherwise, the remote control can not be used as a wireless mouse. - Turn on the projector before turning on the computer
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 66
    WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 67
    1 (Analog) Computer 1 (Digital) Computer 2 Video Wired Wireless Sound Sound Computer Input System (1) Volume Mute Quit SVGA 1 Go to System (3) Go to System (3) See owner's manual "Network Set-up and Operation" See owner's manual "Network Set-up and Operation" N/A........ not applicable 0-31
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 68
    Auto Manual Off Keystone Store/Reset Blue back On/Off Display On/Countdown off/Off Logo Logo select Off Default User Capture Yes lock Off Projector Remote control Quit PIN code lock Off/On1/On2 PIN code change Quit Quit Fan Fan control Warning log Lamp counter Filter counter
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 69
    the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. • • • green. • • • red • • • off • • • blinks green. • • • blinks red. When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 70
    Appendix Compatible Computer Specifications Basically this projector can accept the SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 MAC 19 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA 15 RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 71
    is digital from DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 RESOLUTION 640 x be displayed properly depending on computers. • The specifications are subject to change without notice. 71
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 72
    V-sync. 50-100 Hz Optical Information Projection Image Size (Diagonal) Throw Distance Projection Lens Projection Lamp Adjustable from 40" to 300" 3.1' (0.93m) - 37.6' (11.47m) F1.7-2.5 lens with f=19.2 mm-30.2 mm with manual zoom and focus 275 W Interface Video Input Jack RCA Type x 1 S-video
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 73
    Appendix Accessories Owner's Manual Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Serial Control Cable Lens Cap with String PIN Code Label Network Application (CD-ROM) Soft Carrying Case ● The specifications are subject to change without notice. ● LCD panels are
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 74
    Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer1 (Analog) Computer1 (Digital) RGB (PC digital) RGB (AV HDCP) RGB Computer2 Component RGB (Scart) Auto Video Video S-video Wired Wireless PJLink Input RGB 1 DIGITAL 1 DIGITAL 2 RGB
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 75
    - USB CONNECTOR (Series B) 1 Vcc 21 2 - Data 3 + Data 34 4 Ground LAN TERMINAL 87654321 1 TX + 5 ----- 2 TX - 6 RX - 3 RX + 7 ----- 4 ----- 8 ----- SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN 876 5 43 21 1 R X D 5 ----2 ----- 6 T X D 3 ----- 7 ----4 GND 8 ----- 75
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 76
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 77
    10.2 (257.5) Dimensions 13.15(334) 3.17(80.5) 2.0(51.3) 3.1(78) 3.6(91.3) 2.8(70.5) Appendix Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.472(12.0) 5.1(129.0) 5.2(132.0) 5.5(140.0) 5.1(129.0) 4.4(112.5) 77
  • Sanyo PLC XU115 | Instruction Manual, PLC-XU115 - Page 78
    KF3AC-A SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78

Multimedia Projector
MODEL
PLC-XU115
Owner’s Manual
Network Supported
□ Wireless LAN
IEEE802.11b/g
□ Wired LAN
100-Base-TX/10-Base-T
Memory Viewer
□ SD Card Memory Viewer
*
Refer to the owner’s manuals below for details
about network and memory viewer function.
Network Set-up and Operation
Memory viewer