Sanyo PLC-XU300 Instruction Manual, PLC-XU300A - Page 53

Lamp control, Remote control - projector lamp

Get Sanyo PLC-XU300 - XGA LCD Projector PDF manuals and user guides
UPC - 086483073830
View all Sanyo PLC-XU300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Setting Lamp control Lamp control This function allows you to change brightness of the screen. Normal....... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Lamp life control Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use. Mode 1 The lamp can be turned on even after exceeding the recommended total hours of use. Mode 2 The lamp can be turned on even after exceeding the recommended total hours of use. But the projector turns off automatically after 3 minutes. ✔ Note: • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. • If Mode 2 has been selected and the projection lamp exceeds the recommended total hours of use, the replacement icon will be displayed at the time of power on. Then the projector will turn off after 3 minutes. Lamp replacement icon Lamp life control • The Lamp replacement icon will not appear when the Display function is set to Off (p.46), during Freeze (p.25), or No show (p.26). Remote control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. When operating the projector in "Code 2", both the projector and the remote control must be switched to "Code 2". Remote control To change the code for the projector: Select either "Code 1" or "Code 2" in this Setting Menu. To change the code for the remote control: Press and hold both the MENU and IMAGE buttons together for 5 seconds or more. After changing the code, make sure the remote control operates properly. ✔ Note: • When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector. • If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
53
Remote control
This function allows you to change brightness of the
screen.
Normal
......
Normal brightness
Eco
............
Lower brightness reduces the lamp
power consumption and extends the
lamp life.
Lamp control
Remote control
Lamp life control
This projector provides two different remote control codes:
the factory-set initial code (Code 1) and the secondary code
(Code 2). This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
When operating the projector in "Code 2", both the projector
and the remote control must be switched to "Code 2".
To change the code for the projector:
Select either "Code 1" or "Code 2" in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more.
After changing the code,
make sure the remote control operates properly.
Lamp control
Select the lamp operation when the total lighting time of a
lamp exceeds the recommended total hours of use.
Mode 1
..............
The lamp can be turned on even after
exceeding the recommended total
hours of use.
Mode ±
..............
The lamp can be turned on even after
exceeding the recommended total
hours of use. But the projector turns off
automatically after 3 minutes.
Lamp life control
✔
Note:
• When different codes are set on the projector and on the remote control, any operation cannot be made. In
that case, switch the code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long period of time, the remote control code will be
reset.
✔
Note:
• Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.
• If
Mode ±
has been selected and the projection lamp
exceeds the recommended total hours of use, the
replacement icon will be displayed at the time of power-
on. Then the projector will turn off after 3 minutes.
• The Lamp replacement icon will not appear when the
Display function is set to Off (p.46), during
Freeze
(p.25), or
No show
(p.26).
Lamp replacement icon
Setting