Sanyo PLC XU41 Owners Manual
Sanyo PLC XU41 - XGA LCD Projector Manual
 |
View all Sanyo PLC XU41 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC XU41 manual content summary:
- Sanyo PLC XU41 | Owners Manual - Page 1
Multimedia Projector MODEL PLC-XU41 Owner's Manual - Sanyo PLC XU41 | Owners Manual - Page 2
image size, allowing you to focus on crucial information at a presentation. (See page 31.) ◆ PIN Code Lock Function The PIN code lock function prevents others except users from using the projector. (See page 18 and 43.) ◆ Keystone Adjustment The keystone correction function is provided to correct - Sanyo PLC XU41 | Owners Manual - Page 3
Cabinet 47 Lamp Replacement 48 Lamp Replace Counter 49 Appendix 50 Troubleshooting 50 Indicators and Projector Condition 52 Menu Tree 53 Compatible Computer Specifications 55 Technical Specifications 56 Configurations of Terminals 58 Optional Parts 58 PIN Code Number Memo - Sanyo PLC XU41 | Owners Manual - Page 4
in the "Troubleshooting" section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER - Sanyo PLC XU41 | Owners Manual - Page 5
. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Quick stops - Sanyo PLC XU41 | Owners Manual - Page 6
fans are provided to cool down the projector. This projector monitors internal temperature and control the running speed of the cooling fans. Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Do - Sanyo PLC XU41 | Owners Manual - Page 7
can be determined by turning the equipment off and on, the user is encouraged to try instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers Trade Name Responsible party Address Telephone No. : PLC-XU41 : Sanyo : SANYO - Sanyo PLC XU41 | Owners Manual - Page 8
w Infrared Remote Receiver e Projection Lens r Lens Cover (See page 46 for attaching.) t Air Intake Vent y Top Controls and Indicators u Focus Ring i Zoom Ring o Air Intake Vent !0 Terminals and Connectors !1 Speaker !2 Lamp Cover !3 Air Intake Vent (back and bottom) !4 Air Filter !5 Adjustable - Sanyo PLC XU41 | Owners Manual - Page 9
component input or RGB Scart 21-Pin Video input. (p15, 17) w SERVICE PORT This jack is used to service this projector. e AUDIO IN Connect the audio to this port when you wish to use the PAGE ed buttons on the remote control to scroll back and forth pages on the screen of the connected computer. (p15 - Sanyo PLC XU41 | Owners Manual - Page 10
detects abnormal condition. This also blinks red when the internal temperature of the projector exceeds the operating range. (p45) u LAMP REPLACE indicator Turns yellow when the life of the projection lamp draws to an end. (p48) r SELECT button Executes the item selected. It is also used to - Sanyo PLC XU41 | Owners Manual - Page 11
Part Names and Functions Remote Control ew q COMPUTER VIDEO ON-OFF !5 r !4 MENU VOLUME- SELECT VOLUME+ t !3 !2 y D.ZOOM PAGE KEYSTONE NO SHOW !1 u AUTO PC P-TIMER IMAGE FREEZE MUTE i o !0 Part Names and Functions q POWER ON-OFF button Turns the projector on or off. (p18, 19) w - Sanyo PLC XU41 | Owners Manual - Page 12
the remote control to moisture, or heat. - Do not drop the remote control. - If a battery has leaked on remote control, carefully wipe case clean and install new batteries. - Risk of explosion if battery is replaced by an incorrect type. - Dispose of used batteries according to the instructions. 12 - Sanyo PLC XU41 | Owners Manual - Page 13
lock the adjustable feet and rotate the adjustable feet to adjust the position and tilt. 3 To retract the adjustable feet, lift the front of the projector and pull and undo the feet lock latches. Keystone distortion of the projected image can be adjusted by menu operation. (p22, 39) Adjustable Feet - Sanyo PLC XU41 | Owners Manual - Page 14
plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied. Connect the projector with all peripheral equipment before turning the projector on. (See page 15-17 for connection.) CAUTION For safety, unplug AC - Sanyo PLC XU41 | Owners Manual - Page 15
(MONO) VIDEO USB SERVICE PORT S-VIDEO COMPUTER / / CCOOMMPPOONNEENNTT RESET COMCOPMUPTUETRERIINN 22/ / remote control, connect USB port of your computer to the USB socket of the projector. (p9 and 42) • When connecting AUDIO OUT to external audio equipment, the projector - Sanyo PLC XU41 | Owners Manual - Page 16
VIDEO Cable ✽ • Audio Cables (Mini Plug: stereo Not supplied with this projector.) S-Video Output Composite Video and Audio Output (R) (L) (Video) S-Video L (MONO) VIDEO USB SERVICE PORT S-VIDEO COMPUTER / / CCOOMMPPOONNEENNTT RESET COMCOPMUPTUETRERIINN 22/ / MCMOONOMNIPTIOTOONRRENOOTUUITNT / - Sanyo PLC XU41 | Owners Manual - Page 17
Cable ✽ • Component-VGA Cable ✽ (✽ = Not supplied with this projector.) Installation RGB Scart 21-pin Output Component Video Output (Y, Pb/Cb, Pr/Cr) Audio Output Scart (MONO) VIDEO USB SERVICE PORT S-VIDEO COMPUTER / / CCOOMMPPOONNEENNTT RESET COMCOPMUPTUETRERIINN 22/ / - Sanyo PLC XU41 | Owners Manual - Page 18
"PIN code" and the number will turn red and disappear. Enter a correct PIN code all over again. What is PIN code? PIN code is a security code using Personal Identification Number that allows the person who knows it to operate the projector. Setting PIN code prevents others except the specific users - Sanyo PLC XU41 | Owners Manual - Page 19
continuously without rest. Continuous use may result in shortening the lamp life. Turn off the projector and give it a rest about an hour in every 24 hours. • This projector monitors internal temperature and automatically controls the running speed of the cooling fans. • If the WARNING indicator - Sanyo PLC XU41 | Owners Manual - Page 20
Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Remote Control MENU VOLUME- SELECT VOLUME+ D.ZOOM PAGE KEYSTONE NO SHOW AUTO PC P-TIMER IMAGE FREEZE MUTE Top Control ON - OFF INPUT POWER WARNING VOLUME - VOLUME + KEYSTONE MENU SELECT LAMP - Sanyo PLC XU41 | Owners Manual - Page 21
Basic Operation Menu Bar For computer source Guide Window Shows the selected Menu of the True / Wide / Digital zoom +/-] (p31) Setting Menu Used to change settings of the projector or reset lamp replace counter. (p39-44) Basic Operation Input Menu Used to select input source either Computer or - Sanyo PLC XU41 | Owners Manual - Page 22
no correction. • The arrows disappear at the maximum correction. • The direction of the arrow being corrected turns red. • If you press the KEYSTONE button on the top control or on the remote control once more while the keystone dialog box is being displayed, the keystone adjustment will be canceled - Sanyo PLC XU41 | Owners Manual - Page 23
remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User button to turn up the volume and (-) button to turn down the volume. Mute Press the MUTE button on the remote control to cut off - Sanyo PLC XU41 | Owners Manual - Page 24
the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input Selecting Input Source (Component / RGBScart 21-pin )" on p33. RGB (Scart) See "Selecting Input Source (Component / RGBScart 21-pin )" on p33. Input Menu Computer - Sanyo PLC XU41 | Owners Manual - Page 25
Menu The Auto PC Adjustment function operates to adjust the projector. ----- There is no signal input from computer. Check the connection of your computer and the projector. ( " Troubleshooting" p50 ) Mode 1 User preset system manually adjusted in PC Adjust menu. Adjustment data can be stored - Sanyo PLC XU41 | Owners Manual - Page 26
Auto PC Adjustment can be also executed by pressing the Auto PC button on the remote control unit. To store adjustment parameters Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the - Sanyo PLC XU41 | Owners Manual - Page 27
enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button and the On-Screen Menu will appear - Sanyo PLC XU41 | Owners Manual - Page 28
button. Display area V Adjusts the vertical area displayed by this projector. Press the Point 7 8 button to decrease/increase value and then It is displayed at 5 : 4 aspect ratio with this function off. Reset Resets all adjustment to their previous levels. Store To store adjustment data, move the - Sanyo PLC XU41 | Owners Manual - Page 29
4 by pressing the IMAGE button on the remote control. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for on a blackboard (Green). See above for further description. Image 1~4 User preset image in the Image Adjust Menu (p30). Image Select Menu Image - Sanyo PLC XU41 | Owners Manual - Page 30
(From 0 to 15.) Gamma Press the Point 7 8 button to obtain better balance of contrast. (From 0 to 15.) Reset Resets all adjustment to their previous levels. Store To store the image data adjusted manually, move the red frame pointer to the Store icon and press the SELECT button. The Image Level Menu - Sanyo PLC XU41 | Owners Manual - Page 31
projected image can be also expanded by pressing the D.ZOOM ▲ button on the remote control. ✔Note: • This Screen Menu cannot be operated when "720p(HDTV)", " resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting to the projector. • The image data in other than - Sanyo PLC XU41 | Owners Manual - Page 32
pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source selecting Auto, the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. The projector selects connection in the - Sanyo PLC XU41 | Owners Manual - Page 33
Video Input Input Source Selection (Component, RGB Scart 21-Pin) Direct Operation Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through menu operation as - Sanyo PLC XU41 | Owners Manual - Page 34
to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL - Sanyo PLC XU41 | Owners Manual - Page 35
by pressing the IMAGE button on the remote control. Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture projected on a Blackboard (Green). See above for further description. Image1~4 User preset image in the Image Adjust Menu (p36, 37). Image Select - Sanyo PLC XU41 | Owners Manual - Page 36
Video Input Image Level Adjustment 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust and then press the - Sanyo PLC XU41 | Owners Manual - Page 37
" for a still picture. Film This function is effective on 3:2 pulldown video source. With this function On, the projector reproduces pictures faithful to the original film quality. Reset Resets all adjustment to their previous figure. Store To store the adjustment data, move the red frame pointer to - Sanyo PLC XU41 | Owners Manual - Page 38
Video Input Screen Size Adjustment This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press the MENU button and the On-Screen Menu will appear. - Sanyo PLC XU41 | Owners Manual - Page 39
Reset . . . . .resets the keystone adjustment when the AC power cord is disconnected. Blue back When this function is "On," the projector "No signal" message ● "Wait a moment!" message Logo PIN Code Lock This function prevents others except specific users from changing the Logo setting. Off . . . . - Sanyo PLC XU41 | Owners Manual - Page 40
could no longer change the Logo PIN code setting. For details on PIN code setting, refer to relevant instructions of the PIN Code Lock function on page 43. Logo This function decides what to be displayed on the starting-up display as follows: User . . . . . .the image you captured Default . . . .the - Sanyo PLC XU41 | Owners Manual - Page 41
from a ceiling mounting the projector. Rear When control or remote control unit is pressed. Shutdown . . .When the lamp has been fully cooled down, the power will be turned off. Off The Power Management function is canceled. On start When this function is "On," the projector is automatically turned - Sanyo PLC XU41 | Owners Manual - Page 42
lamp power consumption and extends the lamp life ✔Note: Lamp mode is not switched into Eco mode ( is turned on. ) within 2 minutes after the projector Remote control This projector provides two different remote control codes; the factory-set, initial code (Code 1) and the secondary code (Code - Sanyo PLC XU41 | Owners Manual - Page 43
and provides the following settings for security options. Off the projector is unlocked with the PIN code. On1 requires to enter the PIN code every time turning on the projector. On2...........requires to enter the PIN code to operate the projector once the power cord is disconnected; as long as - Sanyo PLC XU41 | Owners Manual - Page 44
used to reset the lamp replace counter. When replacing the projection lamp, reset the lamp replace counter by using this function. See page 49 for operation. Factory default This function returns all setting values except for the user logo, PIN code lock, logo PIN code lock and the lamp counter to - Sanyo PLC XU41 | Owners Manual - Page 45
lights red and the projector can be turned on. ✔Note: After the temperature inside the projector returns to normal, the WARNING indicator still continues to blink. When the projector is turned on again, the WARNING indicator stops blinking. TOP CONTROL WARNING LECT LAMP REPLACE WARNING blinking - Sanyo PLC XU41 | Owners Manual - Page 46
heat build up and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet. 2 Turn the projector upside down and remove the air filters by pulling the latches upward. 3 Clean the - Sanyo PLC XU41 | Owners Manual - Page 47
dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface. 3 When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. Maintenance and Cleaning 47 - Sanyo PLC XU41 | Owners Manual - Page 48
. Lamp Cover Screw Lamp Screw Screw Handle ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector : ● Replacement Lamp Type No. : PLC-XU41 POA-LMP79 (Service Parts - Sanyo PLC XU41 | Owners Manual - Page 49
a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration - Sanyo PLC XU41 | Owners Manual - Page 50
may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 20 seconds to display an image after turning on the projector. - See if the selected system is corresponding with your computer or video - Sanyo PLC XU41 | Owners Manual - Page 51
See page 15.) WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Give the model number and explain about the - Sanyo PLC XU41 | Owners Manual - Page 52
the air filters. The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the ✽ projector is turned off again, disconnect the AC power cord and contact the dealer or the service center for service and checkup - Sanyo PLC XU41 | Owners Manual - Page 53
signal. PC Adjust Auto PC Adj. Fine sync. Total dots Horizontal Vertical Current mode Clamp Display area Display area - H Display area - V Full screen Reset Mode free Store Quit Appendix RGB Component RGB( Scart ) RGB Auto Video S-Video 0 - 63 On / Off Go to System (1) Go to System (2) N/A Go - Sanyo PLC XU41 | Owners Manual - Page 54
Quit Store / Reset On / Off On / Off Off On PIN code change Quit Off User Default Yes/No On / Off On / Off Computer 2 Monitor out Off Ready Shut down Timer(1-30 Min) Quit On / Off Normal Auto Eco Code 1 Code 2 Mouse / Projector Off Projector Remote Control Quit Off On1 On2 PIN code change Quit L1 - Sanyo PLC XU41 | Owners Manual - Page 55
Appendix Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 130 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION VGA 1 - Sanyo PLC XU41 | Owners Manual - Page 56
Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Multi-media Projector 11.73" x 2.8" x 8.39" (298mm x 71mm x 213mm) (Not including adjustable feet) 6.0 lbs (2.7kgs) 0˚ to 11.8˚ Panel Resolution LCD 60 ˚C) Remote Control Battery Operating - Sanyo PLC XU41 | Owners Manual - Page 57
Accessories Owner's Manual AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String and Screw PIN Code Label Appendix ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are - Sanyo PLC XU41 | Owners Manual - Page 58
Vert.sync.) 11 Ground / ----- 12 ----- 13 Horiz. sync. Input/Output (Composite H/V sync.) 14 Vert. sync. Input / Output 15 ----- SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN Pin Configuration 876 5 43 21 Serial 1 RXD 2 ----3 ----4 GND 5 RTS / CTS 6 TXD 7 GND 8 GND USB CONNECTOR (Series - Sanyo PLC XU41 | Owners Manual - Page 59
number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit - Sanyo PLC XU41 | Owners Manual - Page 60
Printed in Japan Part No. 610 315 6095 (1AA6P1P4571-- MY7A) SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
 |
 |
Multimedia Projector
MODEL
PLC-XU41
Owner’s Manual