Sanyo PLC-XU75 Owners Manual
Sanyo PLC-XU75 - XGA LCD Projector Manual
 |
UPC - 086483072925
View all Sanyo PLC-XU75 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-XU75 manual content summary:
- Sanyo PLC-XU75 | Owners Manual - Page 1
Multimedia Projector MODEL PLC-XU75 PLC-XU78 Owner's Manual - Sanyo PLC-XU75 | Owners Manual - Page 2
, 49, 50) functions. You can lock the operation on the projector and the remote control. Also you can prevent unauthorized persons from using the projector. ◆ Input Search Function Input signal can be searched automatically. (p.46) ✔ Note: • The On-Screen Menu and figures in this manual may differ - Sanyo PLC-XU75 | Owners Manual - Page 3
Lens 54 Cleaning the Projector Cabinet 54 Lamp Replacement 55 Lamp Replacement Counter 56 Appendix 57 Troubleshooting 57 Menu Tree 59 Indicators and Projector Condition 61 Compatible Computer Specifications 62 Technical Specifications 63 Optional Parts 64 Configurations of - Sanyo PLC-XU75 | Owners Manual - Page 4
problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING - Sanyo PLC-XU75 | Owners Manual - Page 5
the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts - Sanyo PLC-XU75 | Owners Manual - Page 6
and to protect it from overheating, and these openings must not be blocked or covered. Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. CAUTION 20˚ Hot air is exhausted from the exhaust vent. When - Sanyo PLC-XU75 | Owners Manual - Page 7
B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number : PLC-XU75/PLC-XU78 Trade Name : Sanyo - Sanyo PLC-XU75 | Owners Manual - Page 8
Part Names and Functions Front q Infrared Remote Receiver w Zoom Ring e Projection Lens r Focus Ring t Lens Cover (See page 53 for attaching.) y Air Intake Vent q we rt y Back !1 y u i o !0 y ✽ Bottom !2 !3 !4 u Power Cord Connector i Speaker o Terminals and Connectors !0 Top Controls - Sanyo PLC-XU75 | Owners Manual - Page 9
PORT This jack is used to service the projector. w COMPUTER IN 1/COMPONENT IN Connect output signal from a computer, RGB scart 21-pin video output, or component video output to this terminal. (p15, 17) When - Sanyo PLC-XU75 | Owners Manual - Page 10
Part Names and Functions Top Control y t u r i e w o q q SELECT button - Execute the selected item. the projector is in the stand-by mode. It remains green while the projector is under operation. (p.18, 19, 61) t LAMP REPLACE indicator Turn yellow when the life of the projection lamp - Sanyo PLC-XU75 | Owners Manual - Page 11
Remote Control ew q r t y u io !0 Part Names and Functions q POWER ON/STAND-BY button Turn the projector on or off. (p.18, 19) w button Temporarily turn off the image on the screen. (p.24) !2 !0 LAMP CONTROL button Select the lamp mode. (p.24, 48) !1 !1 MUTE button Mute the sound. (p. - Sanyo PLC-XU75 | Owners Manual - Page 12
on the remote control, carefully wipe the case clean and install new batteries. ● Risk of explosion if a battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when - Sanyo PLC-XU75 | Owners Manual - Page 13
the adjustable feet and rotate the adjustable feet to adjust the position and tilt. 3 To retract the adjustable feet, lift the front of the projector and press and undo the feet lock latches. Keystone distortion of the projected image can be corrected by menu operation. (p.22, 42) Adjustable - Sanyo PLC-XU75 | Owners Manual - Page 14
or service station if you are not sure of the type of power being supplied. Connect the projector with all peripheral equipment before turning the projector does not match your AC outlet, contact your sales dealer. Projector side For the U.S.A. and Canada Ground AC outlet side For Continental Europe - Sanyo PLC-XU75 | Owners Manual - Page 15
the COMPUTER IN 1/COMPONENT IN and the COMPUTER IN 2/ MONITOR OUT terminal as input. • When connecting the AUDIO OUT to external audio equipment, the projector's built-in speaker is disconnected. • When the cable is of the longer variety, it is advisable to use the COMPUTER IN 1/ COMPONENT IN and - Sanyo PLC-XU75 | Owners Manual - Page 16
for connection • Video and Audio Cable (RCA x 3) • S-VIDEO Cable • Audio Cable (Mini Plug: stereo) ( Cables are not supplied with the projector.) S-Video Output Composite Video and Audio Output (R) (L) (Video) S-Video cable External Audio Equipment Video and audio cable Audio Input S-VIDEO - Sanyo PLC-XU75 | Owners Manual - Page 17
AUDIO IN ✔ Note: • When connecting AUDIO OUT to external audio equipment, the projector's built-in speaker is disconnected. • See page 64 for ordering optional parts. Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. External Audio - Sanyo PLC-XU75 | Owners Manual - Page 18
with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator becomes red. 3 Press the POWER ON/STAND-BY button on the top control or on the remote control. The POWER indicator becomes green and the cooling fans start - Sanyo PLC-XU75 | Owners Manual - Page 19
control or on the remote control, and a message "Power off?" appears on the screen. 2 Press the POWER ON/STAND-BY button again to turn off the projector THE PROJECTOR C O N T I N U O U S LY W I T H O U T R E S T. CONTINUOUS USE MAT RESULT IN SHORTENTING THE LAMP LIFE.TURN OFF THE PROJECTOR AND - Sanyo PLC-XU75 | Owners Manual - Page 20
Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen is not active until the SELECT button is pressed. Top Control POINT buttons (outer ring) MENU button SELECT button Remote Control MENU button POINT buttons SELECT button On-Screen Menu Menu - Sanyo PLC-XU75 | Owners Manual - Page 21
detailed functions, see Menu Tree on p.59,60. For computer source Guide Window Show the selected Menu of the On / Full screen / Digital zoom +/-] (p.32, 34) Setting Menu Used to set the projector's operating configurations. (p.42-51) Input Menu Used to select input source either Computer or - Sanyo PLC-XU75 | Owners Manual - Page 22
If a projected picture has keystone distortion, correct the image with Keystone adjustment. Press the KEYSTONE button on the top control or on the remote control. The keystone dialog box appears. Correct keystone distortion by pressing the Point ed buttons. Keystone adjustment can be memorized - Sanyo PLC-XU75 | Owners Manual - Page 23
previous level, press the MUTE button again or press the VOLUME +/- buttons. Mute function is also effective for AUDIO OUT jack. Top Control Remote Control VOLUME+/buttons VOL- button VOL+ button Menu Operation 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons - Sanyo PLC-XU75 | Owners Manual - Page 24
. Normal. . . normal brightness Auto. . . . . brightness according with the input signal Eco lower brightness reduces the lamp power consumption and extends the lamp life. Remote Control VOLUME +/- buttons (See p.23.) KEYSTONE button (See p.22) POINT ed buttons AUTO PC button D.ZOOM buttons - Sanyo PLC-XU75 | Owners Manual - Page 25
Input Source Selection Direct Operation Choose either Computer 1 or Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. Top - Sanyo PLC-XU75 | Owners Manual - Page 26
XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector the connection between your computer and the projector. (See "Troubleshooting" on page 57.) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The - Sanyo PLC-XU75 | Owners Manual - Page 27
the AUTO PC button on the remote control unit. Remote Control AUTO PC button Menu Operation Auto Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can image is not provided properly with this operation, manual adjustments are required. (p.28, 29) • - Sanyo PLC-XU75 | Owners Manual - Page 28
enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Press - Sanyo PLC-XU75 | Owners Manual - Page 29
buttons to decrease/increase the value. Display area V Adjust the vertical area displayed by this projector. Press the Point 7 8 buttons to decrease/increase the value. Reset To reset the adjusted data, select Reset and press the SELECT button. The confirmation box appears and then select [Yes]. All - Sanyo PLC-XU75 | Owners Manual - Page 30
preset on this projector. Real Picture level with improved halftone for graphics. Blackboard (Green) Picture level suitable for the image projected on a blackboard. See above for further description. Image 1 ~ 4 User preset image in the Image Adjust Menu. (p.32) 30 Remote Control IMAGE button - Sanyo PLC-XU75 | Owners Manual - Page 31
the image. (From 0 to 15.) Gamma Press the Point 7 8 buttons to obtain better balance of contrast. (From 0 to 15.) Reset To reset the adjusted data, select Reset and press the SELECT button. The confirmation box appears and then select [Yes]. All adjustments returns to their previous figures - Sanyo PLC-XU75 | Owners Manual - Page 32
(HDTV), or 1080i (HDTV) is selected in the PC System Menu (p.26). • The projector cannot display any resolution higher than 1600x1200. If your computer's screen resolution is higher than it, reset the resolution to the lower before connecting to the projector. • The image data in other than XGA - Sanyo PLC-XU75 | Owners Manual - Page 33
Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom is selected, the saved scale is used. Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at "Yes". Computer - Sanyo PLC-XU75 | Owners Manual - Page 34
zoom -" is displayed. Press the SELECT button to compress image size. A projected image can be also compressed by pressing the D.ZOOM d button on the remote control. To exit the Digital zoom +/- mode, press any button except the D.ZOOM ed buttons, SELECT, and Point buttons. To return to the previous - Sanyo PLC-XU75 | Owners Manual - Page 35
1 Computer 2 ✳ ✳ See Note at the bottom of this page. Remote Control VIDEO button Menu Operation 1 Press the MENU button to display the On- Auto, the projector automatically detects the incoming video signal, and adjusts itself to optimize its performance. The projector selects a connection - Sanyo PLC-XU75 | Owners Manual - Page 36
Source Selection (Component, RGB Scart 21-pin) Direct Operation Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. Top - Sanyo PLC-XU75 | Owners Manual - Page 37
to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. AV - Sanyo PLC-XU75 | Owners Manual - Page 38
on this projector. Cinema Picture level adjusted for the picture with fine tone. Blackboard (Green) Picture level suitable for the image projected on a blackboard. See above for further description. Image 1~4 User preset image in the Image Adjust Menu (p.39, 40). 38 Remote Control IMAGE button - Sanyo PLC-XU75 | Owners Manual - Page 39
Video Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press - Sanyo PLC-XU75 | Owners Manual - Page 40
"L2" for a still picture. Film . . . Select "Film" for watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT button. The confirmation box appears and then select [Yes]. All - Sanyo PLC-XU75 | Owners Manual - Page 41
This projector has screen ratio of 16:9. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the scale is used. Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT - Sanyo PLC-XU75 | Owners Manual - Page 42
Setting Setting This projector has Setting menu that allows you to set up the other 22) Store . . . . . store the keystone correction even when the AC power cord is unplugged. Reset . . . . . reset the keystone correction when the AC power cord is unplugged. Blue back Press the Point 7 8 buttons to - Sanyo PLC-XU75 | Owners Manual - Page 43
of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Do not decides the start-up display as follows: User . . . . the image you captured Default . . the factory-set - Sanyo PLC-XU75 | Owners Manual - Page 44
computer can be captured up to XGA (1024x768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i. • When capturing the image that has been adjusted by the Keystone function, the adjustment data is automatically reset and the projector captures an image without keystone - Sanyo PLC-XU75 | Owners Manual - Page 45
number, you could no longer change the Logo PIN code setting. For details on PIN code setting, refer to relevant instructions of the PIN code lock function on pages 49 and 50. caution: when you have changed THE LOGO PIn code, write down the new pin code in column of the LOGO - Sanyo PLC-XU75 | Owners Manual - Page 46
the image from a ceiling mounting the projector. Ceiling Rear When this function Lamp are displayed every time the signal is switched. • Only the input source selected at the last time can be detected. • If any of the INPUT button on the top control or COMPUTER/VIDEO button on the remote control - Sanyo PLC-XU75 | Owners Manual - Page 47
as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a signal is reconnected or any button on the top control or remote control is pressed. Shut down . . . . . When the lamp has been fully cooled down, the power is - Sanyo PLC-XU75 | Owners Manual - Page 48
lamp power consumption and extends the lamp life. Remote control This projector provides two different remote control codes remote control operates properly. ✔ Note: If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. Remote control - Sanyo PLC-XU75 | Owners Manual - Page 49
remote control. lock the operation of the remote control. To unlock, use the top control. If the top control accidentally becomes locked and you do not have the romote control or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service - Sanyo PLC-XU75 | Owners Manual - Page 50
code no. memo on page 66, and keep it securely. If you forget your PIN code, the projector can no longer be started. Enter a PIN code The input numbers change to "✳" for security. Move button. The New PIN code input dialog box appears. 50 The input numbers are being displayed for confirmation. - Sanyo PLC-XU75 | Owners Manual - Page 51
-sound than the normal operation (L1), but it takes longer to cool the projector down. Lamp counter This function is used to reset the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement counter by using this function. See page 56 for operation. Factory default - Sanyo PLC-XU75 | Owners Manual - Page 52
. In this case, disconnect the AC power cord and reconnect it, and then turn the projector on once again for check. If the projector cannot be turned the AC power cord and contact the service station for check and repair. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER - Sanyo PLC-XU75 | Owners Manual - Page 53
and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC service station for proper cleaning. Attaching the Lens Cover When moving this projector or while not using it over an extended period of time, replace - Sanyo PLC-XU75 | Owners Manual - Page 54
3 When the projector is not in use, replace the lens cover. Cleaning the Projector Cabinet Follow these steps to clean the projector cabinet. 1 scratch the surface. 3 When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. - Sanyo PLC-XU75 | Owners Manual - Page 55
. Screw Handle Screw ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector : PLC-XU75 / PLC-XU78 ● Replacement Lamp Type No. Service Parts No. : POA-LMP115 610 - Sanyo PLC-XU75 | Owners Manual - Page 56
the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator - Sanyo PLC-XU75 | Owners Manual - Page 57
Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. - Make sure you have properly connected the projector for the monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds - Sanyo PLC-XU75 | Owners Manual - Page 58
for the top control of the projector. (See page 49) WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Give - Sanyo PLC-XU75 | Owners Manual - Page 59
vary depending the input signal. PC Adjust Auto PC Adj. Fine sync. Total dots Horizontal Vertical Current mode Clamp Display area - H Display area - V Reset Mode free Store Quit 0 - 31 H-sync freq. V-sync freq. Quit Yes/No Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Quit Mode 1 Mode 2 Mode 3 Mode 4 Mode - Sanyo PLC-XU75 | Owners Manual - Page 60
On start Lamp control Remote control Security Fan Lamp counter Factory default Quit English German French Italian Spanish Portuguese Dutch Swedish Finnish Polish Hungarian Romanian Russian Chinese Korean Japanese Quit Store/Reset On/Off On/Countdown off/Off Logo select Off Default User Capture Yes - Sanyo PLC-XU75 | Owners Manual - Page 61
dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. • • • green • • • red • • • off • • • blinks green • • • blinks red ✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights - Sanyo PLC-XU75 | Owners Manual - Page 62
Compatible Computer Specifications Basically this projector can accept the Hz) 70.40 58.60 60.00 59.98 60.01 67.19 76.107 60.02 75.025 60.00 65.20 75.60 86.00 (Interlace) 94.00 (Interlace) 60.01 72.00 66.00 86.70 (Interlace) 60.18 85.024 60.190 60.116 59.902 75.06 75.08 75.08 59.88 50.00 60.00 60 - Sanyo PLC-XU75 | Owners Manual - Page 63
~ 100 KHz, V-sync. 50 ~ 100 Hz Optical Information Projection Image Size (Diagonal) Projection Lens Throw Distance Projection Lamp Adjustable from 40" to 300" F 1.65 ~ 1.81 lens with f 22.5 mm ~ 27 mm with manual zoom and focus 4.6' ~ 41.3' (1.4 m ~ 12.6 m) PLC-XU75: 200W PLC-XU78: 220W Interface - Sanyo PLC-XU75 | Owners Manual - Page 64
Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String PIN Code Label Lamp Replacement Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible - Sanyo PLC-XU75 | Owners Manual - Page 65
(Horiz.sync.) 13 Horiz. sync. Input/Output (Composite H/V sync.) 6 Ground (Red) 14 Vert. sync. 7 Ground (Green) 15 DDC clock 8 Ground (Blue) SERVICE PORT CONNECTOR Terminal: Mini DIN 8-PIN 876 5 43 1 Dimensions Serial 1 RXD 2 ----3 ----4 GND 5 RTS/CTS 6 TXD 7 GND 8 GND Unit: inch(mm - Sanyo PLC-XU75 | Owners Manual - Page 66
prominent place of the projector's body while it is locked with a PIN code. Lamp Replacement Label When using the projector ceiling-mounted, put the Lamp replacement label (supplied) on in a prominent place of the projector's body to check the Replacement Lamp Type Number. Lamp Replacement Label 66 - Sanyo PLC-XU75 | Owners Manual - Page 67
KH3AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
 |
 |
Multimedia Projector
MODEL
PLC-XU75
Owner's Manual
PLC-XU78