Sanyo XP30 Instruction Manual, PLC-XP30

Sanyo XP30 - PLC XGA LCD Projector Manual

Get Sanyo XP30 - PLC XGA LCD Projector PDF manuals and user guides View all Sanyo XP30 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo XP30 manual content summary:

  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 1
    Multimedia Projector MODEL PLC-XP30 Owner's Manual
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 2
    projector from the power outlet. READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 3
    conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 4
    equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. AC POWER CORD REQUIREMENT The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 5
    IMAGE 21 AIR FILTER CARE AND CLEANING 39 ZOOM ADJUSTMENT 21 LAMP REPLACEMENT 40 FOCUS ADJUSTMENT 21 LAMP REPLACEMENT MONITOR TIMER 40 LENS SHIFT ADJUSTMENT 21 CLEANING THE PROJECTION LENS 41 KEY STONE ADJUSTMENT 22 TROUBLESHOOTING 42 NO SHOW FUNCTION PICTURE FREEZE FUNCTION 22
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 6
    progressive scan signals and provide fine picture quality. x Multilanguage Menu Display Operation menu is displayed in; English, Deutsch, Français, Italiano, Español, or Japanese. x Wireless Mouse The Remote Control Unit supplied with this projector has Wireless Mouse function for the connected
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 7
    and metallic parts. This area will become hot while the projector is used. This projector detects the internal temperature and automatically controls the operating power of the Cooling Fans. POWER CORD CONNECTOR INFRARED REMOTE RECEIVERS TERMINALS AND CONNECTORS MAIN ON / OFF SWITCH BOTTOM OF
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 8
    your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 11 ~ 14 for connection.) CAUTION For safety, unplug the AC Power Cord when the appliance is
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 9
    projector can be focused from 4.6' (1.4m) ~ 47.3' (14.4m). q Refer to the figure below to adjust the screen size. ROOM LIGHT The brightness in the room has a great influence on the picture 4m) LENS SHIFT ADJUSTMENT The projection lens can be moved up and down with the motor-driven lens shift
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 10
    (Refer to P 22, 31 and 35.) FEET LOCK LATCHES MOVING THE PROJECTOR Use the Carry Handle when moving the Projector. When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and cabinet. When this projector is not in use for an extended period, put it into
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 11
    OUT R G B H V RESET R/C JACK R-AUDIO-L VIDEO INPUT TERMINALS COMPUTER INPUT-1 TERMINALS (DIGITAL/ANALOG) Connect the computer output to one of these terminals. (Refer to P14.) CONTROL PORT (1/2) CONNECTORS When controlling the computer with the Remote Control of this projector, connect the
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 12
    will shut down and restart the unit. Do not use the RESET function excessively. R/C JACK When using the Wired / Wireless Remote Control Unit as the Wired Remote Control, Connect the Wired Remote Control Unit to this jack with the Remote Control Cable (supplied). (Refer to page 17.) MONITOR OUT
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 13
    cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment Projector (STEREO) (MONO) COMPUTER IN 2 R G B H V CONTROL PORT 2 AUDIO 2 Y/VIDEO Cb/Pb Cr/Pr (STEREO) MONITOR OUT R G B H V RESET
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 14
    VGA CABLE (HDB 15 pin) • CONTROL CABLE FOR PS/2 PORT, SERIAL PORT, or ADB PORT • MAC ADAPTER • DVI CABLE (24 pin) ✽ • BNC CABLE (BNC x 5) ✽ • AUDIO CABLES (Mini Plug (stereo) or RCA type) ✽ NOTE : When connecting the cable, the power cords of both the projector and the external equipment should be
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 15
    Power Management mode. (P36) LAMP INDICATOR This indicator is dim when the projector is turned on. And bright when the projector is in stand-by mode. LAMP REPLACE WARNING TEMP. READY LAMP TOP CONTROL P31) NORMAL BUTTON Used to reset to normal picture adjustment preset by factory. (P29, 35) 15
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 16
    REMOTE CONTROL Left Side COMPUTER BUTTON Used to select COMPUTER input source. (P24) COMPUTER VIDEO ON-OFF ZOOM FOCUS VOLUME POWER ON-OFF BUTTON Used to turn the projector minute, release the button and press it again. LASER LENS SHIFT KEYSTONE NO SHOW FREEZE AUTO IMAGE NORMAL P-TIMER
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 17
    LENS SHIFT function. (P21) FREEZE BUTTON Used to freeze the picture. (P22) NORMAL BUTTON Used to reset to normal picture adjustments preset by the factory. (P29, 35) KEYSTONE BUTTON Used to correct the keystone distortion. (P21, 29, 35) Operating Range Point the remote control toward the projector
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 18
    and adjust this projector through the ON-SCREEN MENU. Refer to the following pages to operate each adjustment in the ON-SCREEN MENU. 1 MOVING THE POINTER Move the pointer (see the NOTE below) by pressing POINT button(s) on the TOP CONTROL or the REMOTE CONTROL. WIRELESS REMOTE CONTROL POINT BUTTON
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 19
    MENU Used to adjust Fine sync, Total dots, and Picture Position automatically. (Refer to P29) PC ADJUST MENU Used to adjust the parameters to match with the input signal format. (Refer to P26, 27) SETTING MENU Used to set the Display Menu and reset Lamp Replacement Monitor Timer. (Refer to P36, 37
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 20
    equipment.) 2 Connect the projector's AC Power Cord into a wall outlet and turn the MAIN ON / OFF SWITCH to ON. The LAMP indicator lights RED, and the READY indicator lights GREEN. 3 Press the POWER ON-OFF button on the Remote Control Unit or on the Top Control to ON. The LAMP indicator dims, and
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 21
    UP/DOWN button(s) . Focus The message disappears after 4 seconds. LENS SHIFT ADJUSTMENT 1 Press the LENS SHIFT v/w button(s) on the Top Control or the LENS SHIFT button on the Remote Control Unit. The message "Lens shift" is displayed. 2 Press the LENS SHIFT v button or the POINT UP button to move
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 22
    pressed again or any other function button is pressed. No show The message disappears after 4 seconds. PICTURE FREEZE FUNCTION Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is cancelled when the FREEZE button is pressed again or any other function
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 23
    on the screen for a few seconds. (+) button to increase the volume, and (-) button decreasing. Sound Mute Setting Press the MUTE button on the Remote Control Unit to cut off the sound. To restore the sound to its previous level, press the MUTE button again or press Volume (+/-) button(s). Indicates
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 24
    pressing the MODE button on the Top Control or the COMPUTER button on the Remote Control Unit. MENU OPERATION MODE button COMPUTER computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 42.) SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually, select the mode
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 25
    COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 180 MHz of Dot Clock. ON-SCREEN DISPLAY VGA 1 VGA 2
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 26
    -synchronized picture, a non-centered picture or a skewed picture. This projector has a PC ADJUSTMENT function to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 8 independent memory areas to memorize those parameters manually adjusted
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 27
    sync Adjust the picture as necessary to eliminate flicker from the display. Display area Adjustment of the area displayed with this projector. Select the or "Vert. scale" . Each of the keys operates as follow. Reset Recalls the parameter data that was previously adjusted. Mode free Clears the
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 28
    to select and then press SELECT button. Standard Normal picture level preset on this projector. This picture level can be set by pressing the NORMAL button. Real Picture level adjusted for the picture with fine tone. Custom Picture level adjusted manually in the custom setting dialog box. The level
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 29
    picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Fine sync Adjust the picture as necessary to eliminate flicker from the display. This item can be adjusted manually. (Refer to page
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 30
    the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. 1 Press the MENU button and the , and then press the SELECT button. Each of the keys operates as follow. Reset Recalls the setting data previously set. Stored Stores the setting data in the memory.
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 31
    PICTURE SCREEN ADJUSTMENT This projector has a picture displayed. This projector also enters Digital Zoom mode by pressing the D.ZOOM v/w button on the Remote Control Unit. is higher than 1280 X 1024, reset the resolution to the lower before connecting the projector. q The image data in other than
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 32
    VIDEO button on the Remote Control Unit. MENU OPERATION Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. MODE button VIDEO COMPUTER 1 COMPUTER 2 SELECTING VIDEO SOURCE This projector automatically detects the
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 33
    optimize its performance. When the Video System is PAL-M or PAL-N, select the system manually. This box indicates the system being selected. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce the proper video image, it is necessary to select a specific broadcast signal
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 34
    picture level preset on this projector. This picture level can be set by pressing the NORMAL button. Cinema Picture level adjusted for the picture with fine tone. Custom Picture level adjusted manually Each of the keys operates as follow. Reset Recalls the data previously adjusted. Stored Stores
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 35
    you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Standard" display will be displayed on the screen for a few seconds. Standard VIDEO MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 36
    READY indicator flashes and the Lamp can be turned on again (Power Management mode). In this Power Management mode, the Projection Lamp is automatically turned on when the input signal connected or the projector is operated with any button on the Top Control or the Remote Control. On start When this
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 37
    both projector and Remote Control in the ways above again. NOTE : When the ALL-OFF switch on the Remote Control Unit is turned to "ALL-OFF," the remote transmit code automatically returns to the normal code (Mode 1). Lamp age The Lamp age function is designed to reset the lamp replacement monitor
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 38
    is displayed on the screen. When the menu or the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used. INSTALLATION To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the mouse
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 39
    . Be sure to dry them out. 4 Replace the Air Filters and Air Filter Cover properly. Make sure that they are fully set. CAUTION Do not operate the projector with the Air Filter removed. Dust may accumulate on the LCD Panel and the Mirror degrading picture quality. Do not put small parts into the
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 40
    : Do not reset the LAMP REPLACEMENT MONITOR TIMER when the lamp is not replaced. HANDLE ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. information to the dealer. q Model No. of your projector : PLC-XP30 q Replacement Lamp Type No. : POA-LMP28 (Service Parts No. 610
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 41
    a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning cloth over the lens. 3 When the projector is not in use, replace the lens cover. 41
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 42
    from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back on in order of
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 43
    High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain the difficulty. We will
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 44
    length : 650±20nm) Owner's Manual AC Power Cord Wired/Wireless Remote Control Transmitter and Batteries VGA Cable MAC Adapter Control Cable for PS/2 port Control Cable for Serial port Control Cable for ADB port Remote Control Cable Dust Cover Lens Cover q The specifications are subject
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 45
    Power 22 T.M.D.S. Clock Shield 7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock+ 8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock- CONTROL PORT CONNECTOR Terminal : Mini DIN 8-PIN Connect control you want to use before you turn-on the projector and computer. ON OFF ON DIP 123456 123456
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 46
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 47
  • Sanyo XP30 | Instruction Manual, PLC-XP30 - Page 48
    Printed in Japan Part No. 610 287 0497 (1AA6P1P2355-- MM6A) SANYO Electric Co., Ltd
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Owner's Manual
PLC-XP30
Multimedia Projector
MODEL