Sanyo XU46 Instruction Manual, PLC-XU46
Sanyo XU46 - PLC XGA LCD Projector Manual
 |
UPC - 842740016886
View all Sanyo XU46 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo XU46 manual content summary:
- Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 1
Multimedia Projector MODEL PLC-XU46 Owner's Manual - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 2
operate improperly, read this manual again, check operations and cable connections and try the solutions in the "TROUBLESHOOTING" section at the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 3
Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 4
the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers Trade Name Responsible party Address Telephone No. : PLC-XU46 : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 5
LAMP REPLACEMENT 36 LAMP REPLACE 36 19 LAMP REPLACE COUNTER 37 OPERATING WIRELESS MOUSE 38 19 MAINTENANCE 39 20 WARNING TEMP. INDICATOR 39 20 AIR FILTER CARE AND CLEANING 39 20 CLEANING PROJECTION LENS 39 20 TROUBLESHOOTING 40 20 INDICATORS AND PROJECTOR CONDITION - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 6
crystal display (LCD) technology. N Compact Design This projector is extremely XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector reset a computer output for lower resolution. N Multi-Scan System This projector both projector and computer with Remote Control - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 7
of Cooling Fans. BACK TOP CONTROLS AND INDICATORS INFRARED REMOTE RECEIVER POWER CORD CONNECTOR BOTTOM LAMP COVER ADJUSTABLE FEET AND FEET LOCK LATCHES SPEAKER TERMINALS AND CONNECTORS AIR FILTER AIR INTAKE VENTS (Back and Bottom) This projector is equipped with Cooling Fans for protection from - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 8
into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect the projector with peripheral equipment before turning the projector on. (Refer to pages 11 ~ 13 for connection.) CAUTION For safety, unplug - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 9
LATCHES. Keystone distortion of the projected image can be adjusted by Menu Operation. Refer to page 20 and 35. CAUTION Tilt the projector within the adjustable range in order not to shorten the life of the lamp. Proper angle should be taken. Refer to page 10. ADJUSTABLE FEET FEET LOCK LATCHES 9 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 10
an image. NO DOWNWARD Do not point the projector down to project an image. Do not put the projector on either side to project an image. NO SIDEWAYS MOVING PROJECTOR Use Carry Handle when moving the projector. When moving the projector, replace the Lens Cover and retract the Adjustable Feet to - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 11
button with a pen, which will shut down and restart the unit. Do not use the RESET function excessively. CONTROL PORT CONNECTOR When controlling the computer with Remote Control of this projector, connect the mouse port of your personal computer to this connector. (Refer to P12.) MONITOR OUTPUT - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 12
Port are supplied with this projector. IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA) Desktop type Laptop - Pr / Cr S - VIDEO AUDIO IN R - AUDIO OUT - L COMPUTER RESET CONTROL PORT Use one of these Control Cables corresponding with the terminal of your computer. MCI - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 13
(RCA x 2) These cables are not supplied with this projector. Video Source (example) Video Cassette Recorder Component video output Y - Pb / Cb - Pr / Cr S - VIDEO AUDIO IN R - AUDIO OUT - L COMPUTER RESET Use any of VIDEO jack, S-VIDEO jack, or Y-Pb/Cb-Pr/Cr jacks. • When both VIDEO jack - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 14
. (P17, 18) MUTE D.ZOOM INPUT MENU ALL-OFF SWITCH When using the Remote Control, turn this switch to "ON." And turn it to "ALL OFF" when SHOW FREEZE AUTO PC ADJ. IMAGE P-TIMER POWER ON-OFF BUTTON Used to turn the projector on or off. (P19) INPUT BUTTON Used to select input source. (P22, 29) - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 15
the Remote Control to moisture, or heat. G Do not drop the Remote Control. G If a battery has leaked on Remote Control, carefully wipe case clean and install new batteries. G Risk of explosion if battery is replaced by an incorrect type. G Dispose of used batteries according to the instructions. 15 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 16
BUTTONS (TOP CONTROLS) and INDICATORS on its top. WARNING TEMP. INDICATOR Flashes red when the internal projector temperature is too high. (P39) LAMP REPLACE INDICATOR Turns yellow when the life of the projection lamp draws to an end. (P36) MENU BUTTON Used to open or close MENU operation. (P17, 18 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 17
HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through the ON-SCREEN MENU. Refer to the following pages to value of an item by pressing the POINT button(s) on the Top Control or on the Remote Control. ✽ Pointer is the icon on the ON-SCREEN MENU to select an item. See - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 18
the MENU BUTTON while connecting to PC input source. GUIDE WINDOW Shows selected item of ONSCREEN MENU. PC SYSTEM Digital zoom +/-] (Refer to P28) SETTING MENU Used to change settings of the projector or reset Lamp Replace Counter. (Refer to P34, 35) INPUT MENU Used to select input source either - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 19
appears after 30 seconds. 26 The Preparation Display disappears after 30 seconds. Lamp mode *Refer to page 35 for the Lamp mode. TURNING OFF PROJECTOR 1 Press the POWER ON-OFF button on the Top Control or on the Remote Control, and a message "Power off?" appears on a screen. 2 Press the POWER ON - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 20
the FOCUS button on the Top Control or the FOCUS L/M button on the Remote Control. The message "Focus" is displayed. 2 Adjust focus of image by POINT RIGHT button. PICTURE FREEZE FUNCTION Press the FREEZE button on the Remote Control to freeze the picture on-screen. To cancel the FREEZE function, - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 21
, press the NO SHOW button again or press any other button. No show Message disappears after 4 seconds. P-TIMER FUNCTION Press the P-TIMER button on the Remote Control. The timer display "00 : 00" appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER display - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 22
on the Remote Control. If the projector cannot reproduce This projector accepts various kinds of computer signals including VGA, SVGA, XGA, projector is set correctly. (Refer to TROUBLESHOOTING on page 40.) SELECT COMPUTER SYSTEM MANUALLY PC SYSTEM MENU PC system can also be selected manually - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 23
button on the Remote Control. Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 24, 25.) G Auto - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 24
by Multi-Scan system of this projector. In this case, the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture, and projected improperly. The MANUAL PC ADJUSTMENT function allows you to manually adjust several parameters to match - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 25
Display area V Adjustment of the vertical area displayed with this projector. Press the POINT LEFT/RIGHT button(s) to decrease/increase value clear and then press the SELECT button. Other icons operate as follows. Reset Reset all adjustment to their previous figure. Quit Closes the PC ADJUST MENU. - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 26
3 and Image 4 by pressing the IMAGE button on the Top Control or on the Remote Control. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. IMAGE 1~4 User preset picture adjustment in the IMAGE ADJUST Menu (P27). IMAGE button Standard Real - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 27
button at this icon to store the adjustment. 3 Store To store manually preset image, move the red frame pointer to the Store icon and set and then press the SELECT button. Other icons operate as follows. Reset Reset all adjustment to their previous levels. Image Level Menu Move the red frame - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 28
projected image can be also expanded by pressing the D.ZOOM L button on the Remote Control. Digital zoom - When Digital zoom - is selected, the ON-SCREEN higher than 1280 X 1024, reset the resolution to the lower before connecting projector. G The image data in other than XGA (1024 x 768) is modified - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 29
INPUT SELECTING INPUT SOURCE DIRECT OPERATION Choose Video by pressing the INPUT button on the Top Control or on the Remote Control. If the projector cannot reproduce proper video source, select correct input source through MENU OPERATION (see below). INPUT button Video Computer MENU OPERATION - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 30
Video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 31
Image 4 by pressing the IMAGE button on the Top Control or on the Remote Control. Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture with fine tone. IMAGE 1~4 User preset picture adjustment in the IMAGE ADJUST Menu (P32, 33). IMAGE button Standard - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 32
VIDEO INPUT IMAGE LEVEL ADJUSTMENT 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button(s) to move the red frame pointer to the IMAGE ADJUST Menu icon. 2 Press the POINT DOWN button to move the red frame pointer to the item that you want to adjust and then - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 33
Reset all adjustment to their previous figure. Quit Closes the IMAGE MENU. Store icon Image Level Menu Move the red frame pointer to the image icon to be set and then press the SELECT button. PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 34
function is "On," the picture is top / bottom and left / right reversed. This function is used to project the image from a ceiling mounting the projector. When pressing the SELECT button at Language, the Language Menu appears. Move the pointer to the item and then press the POINT LEFT/RIGHT button - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 35
or ALL-OFF switch is turned to "ALL-OFF," the remote control code automatically returns to the normal code (Code 1). Lamp counter reset This function is used to reset the Lamp Replace Counter. When replacing the Projection Lamp, reset the Lamp Replace Counter by using this function. Refer to page 37 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 36
ASSEMBLY SCREW HANDLE ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer. G Model No. of your projector : G Replacement Lamp Type No. : PLC-XU46 POA-LMP56 (Service Parts No. 610 305 8801 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 37
should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 38
Control as Wireless Mouse, a mouse driver must be already installed on your computer. No mouse driver is supplied with this projector: instead, the Wireless Remote Control becomes the pointing device for your computer's existing mouse driver. Make sure that the mouse driver is properly installed in - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 39
Replace the Air Filter properly. Make sure that the Air Filter is fully inserted. CAUTION Do not operate the projector with the Air Filter removed. Dust may accumulate on the LCD are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING PROJECTION LENS Follow - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 40
APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check the items below once again. G Make sure you have connected the projector to peripheral equipment as described properly in the section "CONNECTING PROJECTOR" on pages 11 ~ 13. G Verify that all computer, - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 41
open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain about the problem. We will advise you how to obtain service. This symbol on the nameplate - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 42
projector is in the Power management mode. • • • on • • • flashing • • • dim • • • off ✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp Replace - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 43
COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal x 600 MAC 16 832 x 624 XGA 1 1024 x 768 XGA 2 1024 x 768 XGA 3 1024 x 768 XGA 4 1024 x 768 XGA 5 1024 x 768 XGA 6 1024 x 768 XGA 7 1024 x 768 XGA 8 1024 x 768 XGA 9 1024 x 768 XGA 10 1024 x 768 H-Freq. ( - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 44
Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System High Definition TV Signal Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Projection Lens Throw Distance Projection Lamp 's Manual AC Power Cord Remote Control - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 45
APPENDIX CONFIGURATIONS OF TERMINALS MONITOR OUT TERMINAL (ANALOG) Terminal : HDB15-PIN Pin Configuration 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 9 +5V Power 2 Green Input 10 Ground (Vert.sync.) 3 Blue Input 11 Sense 0 4 Sense 2 12 DDC Data 5 Ground (Horiz.sync.) 13 Horiz. sync. 6 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 46
Card Imager Kit G Wireless Imager Kit Type No. : POA-MCSRL Type No. : POA-MCMAC Type No. : POA-MACAP Type No. : POA-MD07MCI Type No. : Available models are different in each country. Contact the sales dealer for details. When using Wireless Imager, set the following - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 47
47 - Sanyo XU46 | Instruction Manual, PLC-XU46 - Page 48
Printed in Japan Part No. 610 304 4750 (1AA6P1P3765-- MF3A) SANYO Electric Co., Ltd
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
Multimedia Projector
MODEL
PLC-XU46
Owner’s Manual