Schwinn 130 Upright Bike Assembly Manual

Schwinn 130 Upright Bike Manual

Get Schwinn 130 Upright Bike PDF manuals and user guides View all Schwinn 130 Upright Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 130 Upright Bike manual content summary:

  • Schwinn 130 Upright Bike | Assembly Manual - Page 1
    Do not print this page
  • Schwinn 130 Upright Bike | Assembly Manual - Page 2
    ©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683
  • Schwinn 130 Upright Bike | Assembly Manual - Page 3
    Upright bike Assembly guide PN 001-6896 Rev B (031308) Assembly Guide
  • Schwinn 130 Upright Bike | Assembly Manual - Page 4
    CONTENTS Table of Contents Hardware 2 Exploded View 2 Parts List 4 Assembly Instructions 5 Important Contact Numbers 17 1
  • Schwinn 130 Upright Bike | Assembly Manual - Page 5
    Hardware Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.1270 2
  • Schwinn 130 Upright Bike | Assembly Manual - Page 6
    EXPLODED VIEW EXPLODED VIEW
  • Schwinn 130 Upright Bike | Assembly Manual - Page 7
    PARTS LIST PARTS LIST Ref. Description Qty A Computer 1 A-1 Screw M5x14L 4 A-2 Computer bracket 1 B Handlebar 1 B-4 F-4 Screw M8xP1.25x16L 4 F-7 Seat post pop pin 1 G Seat post 1 G-1 Seat slider 1 G-8 Seat 1 K Pedal pair 1 O
  • Schwinn 130 Upright Bike | Assembly Manual - Page 8
    gather the pieces you need for each step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes. 3. As a general rule, and for all bolts
  • Schwinn 130 Upright Bike | Assembly Manual - Page 9
    ASSEMBLY INSTRUCTIONS Step 1 Install Front and Rear Stabilizers Parts: • Front Stabilizer (Ref. D ) • Rear Stabilizer (Ref. E ) Tools: • Supplied Allen Wrench 1-1 Attach the Rear Stabilizer (E) to the rear of the Main Unit using two M8 X 16mm screws (O-4). 1-2 Attach the Front Stabilizer (D) with
  • Schwinn 130 Upright Bike | Assembly Manual - Page 10
    ASSEMBLY INSTRUCTIONS Step 2 Install Pedals Parts: • Right Pedal (K-R) • Right Pedal (K-L) Tools: • Supplied Pedal Wrench 2-1 Screw the Left Pedal ( has an "L" stamped into the end of the pedal ) into the Left Crank
  • Schwinn 130 Upright Bike | Assembly Manual - Page 11
    ASSEMBLY INSTRUCTIONS Step 3 Install Seat Post Parts: • Seat post (Ref. G) 3-1 Completely unscrew the Seat Post Adjustment Knob (F-7) from the main unit and insert the Seat Post (G) into the hole. Re-install the Adjustment Knob by screwing in firmly into place. G F-7 8
  • Schwinn 130 Upright Bike | Assembly Manual - Page 12
    ASSEMBLY INSTRUCTIONS Step 4 Install Seat Parts: • Seat (Ref. G-8) Tools: • Supplied Wrench 4-1 Position the Seat (G-8) on the top of the Seat Slider. Tilt the the Seat to desired angle and tighten the two nuts on the underside of the Seat until completely tight. Seat Adjustment: To adjust the Seat
  • Schwinn 130 Upright Bike | Assembly Manual - Page 13
    ASSEMBLY INSTRUCTIONS Step 5 Install Handlebar Mast Parts: • Handlebar Mast (Ref C) Tools: • Supplied Allen Wrench 5-1 Remove the four Allen Bolts (F-4) and Curved Washers (F-1) from the frame . 5-2 Connect the Upper and Lower Computer Wires. (
  • Schwinn 130 Upright Bike | Assembly Manual - Page 14
    ASSEMBLY INSTRUCTIONS Step 6 Install Handlebar Parts: • Handlebar (Ref B) • Console Slider Adjust Knob (Ref 0-5) • Washer (Ref 0-6) • "T" Nut (Ref 0-8) 6-1 Tuck the Computer Wires into the Mast to allow insertion of the Handlebar . 6-2 Slide
  • Schwinn 130 Upright Bike | Assembly Manual - Page 15
    ASSEMBLY INSTRUCTIONS Step 7 Install Computer Bracket Parts: • Computer Bracket (Ref. A-2) • assembled view for reference) 7-2 Install and completely tighten the hardware. Note: Use the Angle Adjust Knob to position the Computer to fit individual preferences. O-7 O-1 O-3 A-2 O-3 O-2 Assembled
  • Schwinn 130 Upright Bike | Assembly Manual - Page 16
    ASSEMBLY INSTRUCTIONS Step 8 Install Computer Parts: • Computer (Ref. A ) Tools: • Supplied Phillips Head Screwdriver 8-1 Remove the four screws from the back of the Computer. 8-2 Connect the Computer Wire and Heartrate Wire to
  • Schwinn 130 Upright Bike | Assembly Manual - Page 17
    ASSEMBLY INSTRUCTIONS Step 9 Install Bottle Cage Parts: • Bottle Cage (Ref. C-2 ) Tools: • Supplied Phillips Head Screwdriver 9-1 Remove the two M5 x 20L (Ref. C-3) screws from the Mast. 9-2 Align Bottle Cage with the holes in
  • Schwinn 130 Upright Bike | Assembly Manual - Page 18
    ASSEMBLY INSTRUCTIONS Step 10 Plug in AC Adapter Parts: • AC Adapter (Ref. P) 10-1 Plug the AC Adapter (P) into the recepticle on the rear left of the unit and into a 110 volt outlet. P 15
  • Schwinn 130 Upright Bike | Assembly Manual - Page 19
    ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner's Manual for information regarding computer operation, product maintenance, Warranty informa- tion, and general fitness and exercise guidelines. 16
  • Schwinn 130 Upright Bike | Assembly Manual - Page 20
    -NAUTILUS (800-628-8458) Fax: 800-898-9410 • TECHNICAL/CUSTOMER SERVICE Nautilus, Inc. World Headquarters 16400 SE Nautilus Drive Vancouver, Washington, USA 39-031-51-10-86 Fax: +39-031-34-24-97 • UNITED KINGDOM OFFICE Nautilus UK Ltd. Tel: +44-1908-267-345 Fax: +44-1908-267-346 • CHINA OFFICE
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Do not print this page