Schwinn 203 Recumbent Exercise Bike Assembly Manual
Schwinn 203 Recumbent Exercise Bike Manual
 |
View all Schwinn 203 Recumbent Exercise Bike manuals
Add to My Manuals
Save this manual to your list of manuals |
Schwinn 203 Recumbent Exercise Bike manual content summary:
- Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 1
201/203 Schwinn® Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions 201 Recumbent Exercise Bike 203 Recumbent Exercise Bike - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 2
injury, please read the following precautions before using the Schwinn 201/203. 1. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature and follow them - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 3
201/203 Schwinn Recumbent Bike Parts List, Hardware Chart, and Assembly Instructions Assembly of the 201/203 Recumbent Bike is divided into 5 easy stages; each comprised of only a few setup steps. Before proceeding with the assembly, please read over the easy to follow instructions to familiarize - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 4
1 1pr 8 4 1pr 19 2 2 1 1 1 1 1 1 1 1 4 1 1 2 1 1 Parts List Description Reference # Allen Bolt M8 x P1.25 x 45mm 1 Flat Washer 2 Seat Pin Adjustment Knob 3 Seat HR Cable (Lower) 26 Console Mast Cover 27 Computer Cable (Upper) 28 HR Cable (Upper) 29 Console Mast 30 Main Unit 31 - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 5
Wrench) Stage#5 O C) Curved Washer 05*019*2t (4) MOR RE) O Allen Bolt M8xP1.25x16mm (4) Screw m5.12MM (2) Allen Key (1) Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 6
201/203 Assembly Drawing with Reference Numbers 34 27 3 17 19 ?-) 7 22' 57 30 1 32 80 19 7. 1 1 2 22 10 - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 7
Replacement Parts List Reference # Description Part # 3 Seat Pin Adjustment Knob 18079 4 Seat 18051(201) 18089(203) 5 Seat Back 18050(201) 18088(203) 6 Handlebar Assembly 18049(201 Console Mast Cover 18058 28 Computer Cable (Upper) 18085 29 HR Cable (Upper) 18086 30 Console - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 8
and parts with the enclosed parts list and full size hardware chart. Each step of the assembly process has been broken down into 5 easy-to-follow stages. Please take just a few moments to read over these instructions to familiarize yourself with the process to make assembly quick and trouble-free - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 9
Step 3: Attach SEAT BACK (#5) to SEAT FRAME (#8) with 4 ALLEN BOLTS (#1) and 4 WASHERS (#2). Tighten Bolts. Note: Finished seat should look like picture below: - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 10
Assembly Stage #2 Attach Rear Stabilizer and Seat Rail to Seat Assembly 2 2 2-- t STEP4 1- 141 0 4 STEPS 1 1 1 9 7 1 1 STEP7 10 Assembly hardware required: (4) M8 Allen Bolts 16mm (item #22) (4) Flat Washers 08 * 019 * 2T(item#2) Step 4: Attach SEAT RAIL (#9) to REAR STABILIZER TUBE (# - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 11
from the right pedal. Counterclockwise rotation tightens while Clockwise rotation loosens on the left pedal. To avoid stripping of the threads be careful to use the proper pedal. Attach PEDAL STRAPS (#18) to each PEDAL (#21). Again, each strap is labeled with an R or an L corresponding to the right - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 12
seat rail. Connect the cables from MAIN UNIT and Seat Rail. Tape can be used around the attachment of the two cable ends to ensure that they do not become disconnected rail. Slide the seat rail slowly into the main unit. Using a flashlight check to make sure that the cable is not protruding from the bottom - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 13
of the handlebar assembly. Feed the remaining excess wire into the seat rail and replace the end cap on the end of the seat rail. After completing assembly stage 5 verify that the handgrip heart rate works by hitting manual start and then placing your hand on the grip heart pad located on the - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 14
& #26) as well as the COMPUTER CABLE (#28 & #25). To easily complete this step it would be helpful to have someone hold the CONSOLE MAST (#30) and CONSOLE MAST COVER (#27) while connecting the cables. Fasten with 4 BOLTS (#22) and 4 CURVED WASHERS (#19). Tighten with provided Allen wrench. Step 14 - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 15
extension. That's it! You're finished and now you can begin to reach your fitness goals! Please reference the Owner's Manual for information regarding computer operation, product maintenance, warranty information, and general fitness and exercise guidelines. Schwinn Customer Service 1.800.864.1270 - Schwinn 203 Recumbent Exercise Bike | Assembly Manual - Page 16
Troubleshooting the Schwinn 201, 203 Recumbent Exercise Bike TIP: Use assembly diagram(s) as reference when troubleshooting unit. PROBLEM: Computer will not start, function, or is blank... (SOLUTION): 1. Ensure the batteries the unit is plugged into a 110v outlet. 2. Check the wiring connections
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
201/203
Schwinn®
Recumbent
Exercise
Bike
Parts
List
Full
Size
Hardware
Chart
Product
Illustration
Assembly
Instructions
201
Recumbent
Exercise
203
Recumbent
Exercise
Bike
Bike