Schwinn 222 Recumbent Exercise Bike Assembly Manual

Schwinn 222 Recumbent Exercise Bike Manual

Get Schwinn 222 Recumbent Exercise Bike PDF manuals and user guides View all Schwinn 222 Recumbent Exercise Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 222 Recumbent Exercise Bike manual content summary:

  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 1
    222 Schwinn® Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 2
    3 warnings listed below are also located on the computer console mast of the exercise bike. Failure to follow any of these safeguards may result in injury or serious health problems. • Read and understand the Owner's Manual and operation instructions prior to use. If you do not have an Owner
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 3
    . This is to ensure adequate clearance for easy access to the bike and to avoid any possible contact with the moving pedals 222 Schwinn Recumbent Bike Parts List, Hardware Chart, and Assembly Instructions Assembly of the 222 Recumbent Bike is divided into 5 easy stages; each comprised of only a few
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 4
    HR Wire Front Stabilizer Flathead Screw 8x16L Main Frame Pedals Flat Washer Seat Rail Post Rear Stabilizer Seat Rail Seat Rail HR Wire Seat Handlebar Seat Adjustment Knob Small Flat Washer Seat Bottom Allen Bolt 8x1.25x45L Seat Support Frame Seat Back Bottle Holder Screw 5x14L AC Adaptor Reference
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 5
    Flat Washer ? 8*? 16*2T Allen Bolt M8xP1.25x16mm Screws M8xP1.25x16mm Flat Washer ? 8*? 16*2T Screwdriver Allen Key Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 6
    222 Assembly Drawing with Reference Numbers
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 7
    HR Wire Front Stabilizer Flathead Screw 8x16L Pedals Flat Washer Seat Rail Post Rear Stabilizer Seat Rail Seat Rail HR Wire Seat Handlebar Small Flat Washer Seat Bottom Allen Bolt 8x1.25x45L Seat Support Frame Seat Back Bottle Holder Screw 5x14L AC Adaptor Part # 18165 18200 18094 18197 18001 18098
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 8
    down into 6 easy-to-follow stages. Please take just a few moments to read over these instructions to familiarize yourself with the process to make assembly quick and trouble-free. Assembly Stage #1 Assemble Seat and Handle Bar Assembly hardware required: (8) M8 Allen Bolts 45 mm long (item #25
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 9
    Step 3: Attach SEAT (#23) to SEAT FRAME (#26) with 4 ALLEN BOLTS 45mm (#25) and 4 WASHERS (#15). Tighten Bolts. Step 4: Attach SEAT BACK (#27) to SEAT FRAME (#26) with 4 ALLEN BOLTS 45mm (#25) and 4 WASHERS (#15). Tighten Bolts. Note: Finished seat should look like picture below:
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 10
    FLAT WASHERS (#15) and 4 ALLEN BOLTS (#5). Tighten bolts Step 7: Insert SEAT PIN ADJUSTMENT KNOB (#3) into SEAT FRAME (#8). Slide the seat assembly from stage 1 onto the SEAT RAIL (#9). Tighten seat assembly to the rail with the SEAT PIN ADJUSTMENT KNOB (#3). Insert HR CABLE (#47) into HR input on
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 11
    13) with 2 FLAT SCREWS (#12). Tighten Bolts with provided wrench. Step 9: Attach RIGHT PEDAL (#14) to the right crank arm on the MAIN UNIT (#31). Thread the pedal onto the crank arm and then tighten with pedal wrench. Attach LEFT PEDAL (#14) to the left crank arm on the MAIN UNIT (#13). Thread the
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 12
    CAUTION! Be careful not to pinch the heart rate wires between the seat rail and the receiver on the main unit. Failure to do so cause damage to the wires and cause the heart rate feature not to function. Attach the SEAT RAIL to the MAIN UNIT (#13) with 3 16mm ALLEN BOLTS (#5) and 3 FLAT WASHERS
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 13
    ASSEMBLY STAGE #5 Attach Handlebar Assembly and Run Cabling Through Handlebar Post Assembly Hardware Required: NONE Step 11: Slide the HANDLEBAR ASSEMBLY (#2) into the receiver on the HANDLEBAR POST (#4). Slide the threaded post into the slider tube and attach the HANDLEBAR ASSEMBLY SLIDER TUBE
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 14
    Assembly Stage #6 Attach Console Mast to Main Unit Assembly Hardware Required: (4) Allen Bolts 16 mm long (item #5) (4) Curved Washers (item #6) (4) Computer Screws (item #3) Step 13: Before sliding the HANDLEBAR POST (#4) onto the MAIN UNIT (#13), attach both HR CABLES (#7 & #10) as well as the
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 15
    pedal at full extension. That's it! You're finished and now you can begin to reach your fitness goals! Please reference the Owner's Manual for information regarding computer operation, product maintenance, warranty information, and general fitness and exercise guidelines. Schwinn Customer Service
  • Schwinn 222 Recumbent Exercise Bike | Assembly Manual - Page 16
    Troubleshooting the Schwinn 222 Recumbent Exercise Bike TIP: Use assembly diagram(s) as reference when troubleshooting unit. PROBLEM: Computer will not start, function, or is blank... (SOLUTION): 1. Ensure the batteries the unit is plugged into a 110v outlet. 2. Check the wiring connections and
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
222 Schwinn
®
Recumbent Exercise Bike
Parts List
Full Size Hardware Chart
Product Illustration
Assembly Instructions