Schwinn 226 Recumbent Bike Assembly Manual

Schwinn 226 Recumbent Bike Manual

Get Schwinn 226 Recumbent Bike PDF manuals and user guides View all Schwinn 226 Recumbent Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 226 Recumbent Bike manual content summary:

  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 1
    Do not print this page
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 2
    ©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 3
    RECUMBENT ASSEMBLY GUIDE PN 001-6962 REV B (090706) ASSEMBLY GUIDE
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 4
    CONTENTS Table of Contents Hardware 2 Exploded View 4 Parts List 5 Assembly Instructions 6 Important Contact Numbers 21 1
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 5
    HARDWARE Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.1270 2 I-10 Carriage Bolt M8xP1.25x85MM (1) I-1 M8xP1.25x85mm I-4 lock nut for M8 � (1)
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 6
    Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.1270 3 I-7 Allen Bolt M8xP1.0x45mm (4) Allen Key���� 4) I-3 Regular Washer 8*16*2t(15) I-5
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 7
    EXPLODED VIEW EXPLODED VIEW � � � ��� ��� ���� ��� ��� ��� ��� ���� ���� ���� � � ��� ��� ��� � ��� ���� � 4
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 8
    PARTS LIST PARTS LIST Ref. Description Qty A Computer 1 A-1 Computer bracket 1 A-2 Screw M5x14L 4 B Handlebar 1 C Handlebar mast 1 C-1 Screw M8x1.25X16 4 C-2 Curved Washer 4 C-3 Upper heart rate wire 1 C-4 Upper Computer Wire 1 D Main
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 9
    gather the pieces you need for each step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes. 3. As a general rule, and for all
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 10
    ASSEMBLY INSTRUCTIONS Step 1 Install Front and Rear Stabilizers Parts: • Front Stabilizer (Ref. E ) • Rear Stabilizer (Ref. G ) • M8x16 Screws (Ref. I-6) Tools: • Supplied Allen Wrench 1-1 Attach the Rear Stabilizer (G) to the rear of the Main Unit using two M8 X 16mm screws (I-6). 1-2 Attach the
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 11
    ASSEMBLY INSTRUCTIONS Step 2 Install Pedals Parts: • Right Pedal (F-R) • Right Pedal (F-L) Tools: • Supplied Pedal Wrench 2-1 Screw the Left Pedal ( has an "L" stamped into the end of the pedal ) into the Left Crank Arm. Note: The Left Pedal has a
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 12
    ASSEMBLY INSTRUCTIONS Step 3 Install Handlebar Parts: • Seat Frame (Ref. L) • Handlebar (Ref. J) • Four M8x16 screws (Ref. I-5) • Four 8x16x2 Washers (Ref. I-3) Tools: • Supplied Allen Wrench 3-1 Align Handlebar with holes in Seat Frame. 3-2 Install and completely tighten the hardware. L J I-5 I-3
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 13
    ASSEMBLY INSTRUCTIONS Step 4 Install Seat Bottom Parts: • Seat Bottom (Ref. K-1) • Four M8x1x45 Screws (Ref. I-7) • Four 8x16x2 Washers (Ref. I-3) Tools: • Supplied Allen Wrench 4-1 Align the Seat Bottom (K-1) with the Seat Frame. 4-2 Install and completely tighten the hardware. K-1 I-3 I-7 10
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 14
    ASSEMBLY INSTRUCTIONS Step 5 Install Seat back Parts: • Seat Bottom (Ref. L-1) • Four M8x1x45 Screws (Ref. I-7) • Four 8x16x2 Washers (Ref. I-3) Tools: • Supplied Allen Wrench 5-1 Align the Seat Back (L-1) with the Seat Frame. 5-2 Install and completely tighten the hardware. Note: There are two
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 15
    ASSEMBLY INSTRUCTIONS Step 6 Install Bottle Holder Parts: • Water Bottle Holder (Ref. K-2) • Four M5x16 Screws (Ref. I-8) Tools: • Supplied Phillips Head Screwdriver 6-1 Align the Water Bottle Holder under the left side of the Seat Bottom. 6-2 Install and completely tighten the hardware. I-8 K-2
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 16
    ASSEMBLY INSTRUCTIONS Step 7 Prepare to Install Seat Assembly Tools: • Supplied Allen Wrench 7-1 Unscrew the the seven screws and washers (D-18) that secure the Seat Rail (H) and remove the Seat Rail from the unit. (Figure A) Note:
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 17
    ASSEMBLY INSTRUCTIONS Step 8 Install Seat Assembly Parts: • Seat Assembly (From step 3-6) • Seat Rail (Ref. H) • Seat Rail Bracket (Ref. D-22) Tools: • Supplied Allen Wrench 8-1 Pull out on the Seat Adjustment Knob (K-3) while sliding the Seat Assembly onto the Seat Rail (H). Release the
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 18
    ASSEMBLY INSTRUCTIONS Step 9 Install Handlebar Mast Parts: • Handlebar Mast (Ref C) Tools: • Supplied Allen Wrench 9-1 Remove the four Allen Bolts (C-1) and Curved Washers (C-2) from the frame . 9-2 Connect the Upper and Lower Computer Wires and Heart Rate Wires. (Detail A) 9-3
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 19
    ASSEMBLY INSTRUCTIONS Step 10 Install Handlebar Parts: • Handlebar (Ref B) • Washer (Ref I-3) • Screw M8x16 (Ref I-5) 10-1 Tuck the Computer Wires into the Mast to allow insertion of the Handlebar . 10-2 Slide the Handlebar (B)
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 20
    ASSEMBLY INSTRUCTIONS Step 11 Install Computer Bracket Parts: • Computer Bracket (Ref. A-1) • Angle Adjust Knob (Ref. I-2) • Carriage Bolt M8x1.25x85 (Ref. I-10) • Screw M8x85 (Ref. I-1) • 2 Washers (Ref. I-3) • Hex Nut (Ref. I-4) Tools: • Supplied Socket and Flat Wrenches 11-1 Align the Computer
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 21
    ASSEMBLY INSTRUCTIONS Step 12 Install Computer Parts: • Computer (Ref. A ) Tools: • Supplied Phillips Head Screwdriver 12-1 Remove the four screws from the back of the Computer. 12-2 Connect the Computer Wire and Heartrate Wire to the connectors
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 22
    ASSEMBLY INSTRUCTIONS Step 13 Plug in AC Adapter Parts: • AC Adapter (Ref. D-17) 13-1 Plug the AC Adapter (P) into the recepticle on the front right of the unit and into a 110 volt outlet. D-17 19
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 23
    ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner's Manual for information regarding computer operation, product maintenance, Warranty information, and general fitness and exercise guidelines. 20
  • Schwinn 226 Recumbent Bike | Assembly Manual - Page 24
    (800-6288458) For technical assistance and a list of distributors in your area, please call or fax one of the following numbers. • INTERNATIONAL CUSTOMER SERVICE: Nautilus International S.A. Rue Jean Prouvé 6 1762 Givisiez / Switzerland Tel: + 41-26-460-77-77 Fax: + 41-26-460-77-70 Email: technics
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Do not print this page