Schwinn 430 Elliptical 2007 model Assembly Manual

Schwinn 430 Elliptical 2007 model Manual

Get Schwinn 430 Elliptical 2007 model PDF manuals and user guides View all Schwinn 430 Elliptical 2007 model manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 430 Elliptical 2007 model manual content summary:

  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 1
    Do not print this page
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 2
    ©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 3
    elliptical Assembly guide 001-6986-070709C Assembly Guide
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 4
    CONTENTS Table of Contents Hardware 2 Exploded View 4 Parts List 5 Assembly Instructions 6 Important Contact Numbers 18 Attention! When unpacking the box, please inspect all styrofoam and packaging before discarding. Some parts are packaged on the outside of the styrofoam packaging. 1
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 5
    WASHER REGULAR (36) M8 x 20L BUTTON HEAD (4) M8 WAVE WASHER (2) M8 x 15L BUTTON HEAD (32) M8 WASHER WIDE (4) Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 6
    HARDWARE CARD M8 WASHER LOCKING (40) REGULAR (36) M8 x 25L FLAT HEAD THREAD LOCK (6) END CAPS (4) ALLEN WRENCH (1) Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 7
    Exploded View EXPLODED VIEW P K J L Q A C S J T W E U D F O V T B R M H G I 4
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 8
    K Console Mast 1 L Arm Pivot Rod 1 M Lower Left Handlebar 1 O lEFT Upper Handlebar 1 P Right Upper Handlebar 1 Q Right Lower Handlebar 1 R Left Leg 1 S Right Leg 1 T Foot Mount Plate 2 U Console 1 V ASSEMBLY/OWNER MANUALS 1 W AC
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 9
    step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes. 3. As a general rule, and for all bolts and nuts, turn bolts or nuts toward
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 10
    ASSEMBLY INSTRUCTIONS Step 1 Install Rear Stabilizer and Extrusion Handlebar Parts: • Two Extrusion Assemblies (Ref. H) • Rear Stabilizer (Ref. G ) • Extrusion Handlebar Assembly (Ref. I) Tools Supplied Allen Wrench 1-1 Attach, but do not tighten, the Extrusion Assemblies (Ref H) to the
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 11
    ASSEMBLY INSTRUCTIONS Step 2 Install front stabilizer and Extrusion Assembly Parts: • Front Stabilizer (Ref E) • Extrusion Assembly (From step 1) • Main Unit (Ref A) Tools Supplied Allen Wrench 2-1 Attach the Front Stabilizer (Ref E) to the Main Unit (Ref A) using two M8x25 flat head
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 12
    ASSEMBLY INSTRUCTIONS Step 3 Install Console Mast Parts: • Console Mast (Ref K) Main Unit Tools Supplied Allen Wrench 3-1 Connect the wire harness from the Main Unit to the wire harness in the Console Mast. 3-2 Slide the Console Mast (Ref K) down onto the Main Unit and secure using
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 13
    ASSEMBLY INSTRUCTIONS Step 4 Install Console Handlebar Parts: • Console Handlebar (Ref D) Tools Supplied Phillips Head Screwdriver 4-1 Feed the Wire Harness (Ref W1) from the Mast (Ref K) and the Contact Heart Rate Wire (Ref W2) from the Console Handlebar through the hole in the
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 14
    ASSEMBLY INSTRUCTIONS Step 5 Install Console Parts: • Console (Ref U) Tools Supplied Phillips Head Screwdriver NOTE: Before installing the console, make sure the toggle switch on the back of the Console (beside wire connectors) is set to EP. 5-1 Remove the four M5x10 phillps screws (Ref 9) from
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 15
    ASSEMBLY INSTRUCTIONS Step 6 Install Right and Left leg Parts: • Right Leg (Ref R) • Left Leg (Ref S) Tools Supplied Combo Wrench 6-1 Attach the Right leg (Ref S), marked with an "R" sticker that can be removed, to the post on the Crank (Ref C1) using one
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 16
    ASSEMBLY INSTRUCTIONS Step 7 Install Right and Left Lower Handlebars Parts Arm Pivot Rod (Ref L Right Lower Handlebar (Ref Q Left Lower Handlebar (Ref M) Tools 2 Supplied Combo Wrenches 7-1 Slide the Arm Pivot Rod (Ref L) through the Console Mast (Ref K). 7-2 Slide the Right Lower Handlebar (
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 17
    ASSEMBLY INSTRUCTIONS Step 8 Install Right and Left Foot Assembly Parts Foot Mount Plate Qty.2 (Ref T Right Foot Assembly (Ref C Left Foot Assembly (Ref B Arm Cotter Pin (Ref N) Tools Supplied Allen Wrench 8-1 Slide the shaft under the Left Foot Assembly into the Pivot (Ref P1) on the
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 18
    ASSEMBLY INSTRUCTIONS Step 9 Install Upper Handlebars Parts: • Right Upper Handlebar (Ref P) • Left Upper Handlebar (Ref O) Tools Supplied Allen Wrench 9-1 Slide the Upper Left Handlebar (Ref O) into the Lower Left Handlebar and secure using four M8x15l button head (Ref 1) four M8
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 19
    ASSEMBLY INSTRUCTIONS Step 10 Install Water Bottle Holder and AC Adapter Parts: • Water Bottle Holder (Ref F) • AC Adapter (Ref W) Tools Supplied Phillips Screwdriver 10-1 Align the Water Bottle Holder components (Ref F) with the Mast as shown and secure using two M5x20 phillips head (Ref
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 20
    ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner's Manual for information regarding computer operation, product maintenance, warranty information, and general fitness and exercise guidelines. 17
  • Schwinn 430 Elliptical 2007 model | Assembly Manual - Page 21
    need assistance, please have both the serial number of your machine and the date of purchase available when you contact the Phone: 800-NAUTILUS (800-6288458) Fax: 800-898-9410 • TECHNICAL/CUSTOMER SERVICE Nautilus, Inc. World Headquarters 16400 SE Nautilus Drive Vancouver, Washington, USA 98683
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
Do not print this page