Schwinn Journey 1.0 Upright Bike Assembly and Owner's Manual
Schwinn Journey 1.0 Upright Bike Manual
View all Schwinn Journey 1.0 Upright Bike manuals
Add to My Manuals
Save this manual to your list of manuals |
Schwinn Journey 1.0 Upright Bike manual content summary:
- Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 1
130 / 170 / 1.0 1.5 Manual en Español Latino Americano: http://www.schwinnfitness.com ASSEMBLY MANUAL / OWNER'S MANUAL - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 2
Assembly 5 Parts 6 Hardware 7 Tools 7 Assembly 8 Leveling the Bike 14 Moving the Bike 14 Important Safety Instructions - Owner's 15 Features 16 Console Features 17 Contact Heart Rate (CHR) 20 Operations 22 Adjustments 22 Initial Setup 22 Quick Start / Manual Program 23 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 3
connect power supply to the machine until instructed to do so. • Do not parts can cause a risk to users, keep the machine from operating correctly and void the warranty. • Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Manual - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 4
age. • Prior to use, read and understand the Owner's Manual. • Injury or death is possible if Caution is not blessures. • Cette machine supporte un poids maximal de 300lbs machine and power supply comply with part 15 of the FCC rules. Operation accordance with the instructions, may cause harmful - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 5
For safe operation, the location must be on a hard, level surface. Allow a workout area of a minimum 90" x 70" (2.3m x 1.8m). Basic Assembly Tips ) to tighten, and the left (counter- clockwise) to loosen, unless instructed otherwise. 4. When attaching 2 pieces, gently lift and look through the - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 6
PARTS 8 7 15 2 6 16 14 5 4 11 9 1 12 (L) 10 13 (R) 3 Item Qty Description 1 1 Main Frame 2 1 Front Stabilizer 3 1 Rear Stabilizer 4 1 Top Shroud 5 1 Mast Gasket 6 1 Console Mast (with Handlebar Mount) 7 1 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 7
HARDWARE / TOOLs D E Item Qty Description A 4 Button Head Hex Screw M8 x 25 B 5 Lock Washer M8 C 4 Curved Washer M8 D 1 Flat Washer M8 E 1 T-handle Tools Included Not Included 6 mm (recommended) 7 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 8
(*) is pre-installed on the stabilizers and not on Hardware Card. Make sure transport wheels on the front stabilizer point forward, and the Schwinn® decal on the rear stabilizer faces outward from the machine. 6 mm X2 * * * 6 mm X2 * * * 2. Install Console Mast, Mast Gasket and Top Shroud on - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 9
3. Install Handlebars on Console Mast NOTICE: D o not crimp the cables. Put the Handlebar (7) in the bracket (6a), adjust the Handlebar to the desired angle, and install the T-handle (E) through the holes. Use the pull cable in the Handlebar Mount to route the HR cable (7a) through the slot (6c) - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 10
4. Install Console on Console Mast Note: Remove the pre-installed screws(*) from the back of the Console before you connect the cables. NOTICE: D o not crimp the cables. 8 X4 * #2 8 X4 * #2 10 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 11
5. Install Seat Post on Frame NOTICE: M ake sure the Adjustment Knob engages the Seat Post. Do not set the Seat Post position higher than the stop mark (STOP) on the tube. 9 10 STOP 10 6. Attach Seat to Seat Post NOTICE: B e sure the Seat is straight. Tighten the nuts (11b) on the Seat bracket ( - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 12
7. Install Pedals Note: T he Left Pedal is reverse-threaded. Be sure to attach Pedals on the proper side of the Bike. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". 13 (R) 12 (L) 12 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 13
hardware is tight and components are properly assembled. Be sure to record the serial number in the field provided at the front of this manual. ! Do not use or put the machine into service until the machine has been fully assembled and inspected for correct performance in accordance with the Owner - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 14
knob to adjust the stabilizer foot. Make sure the bike is level and stable before you exercise. Moving Your Bike To move the upright bike, carefully tilt the Handlebars toward you while pushing the front of the bike downward. Push the bike to the desired location. NOTICE: B e careful when you move - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 15
Manual. Keep the Manual for future reference. Read and understand all warnings on this machine. If at any time the Warning stickers become loose, unreadable or dislodged, contact Nautilus® Customer Service for replacement stickers. • Children must not be let on or near to this machine. Moving parts - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 16
FEATURES C B D E F G H A Q P A O M N L B K R J I F A Console B Handlebars C Adjustable Seat D Adjustment Knob E Pedals F Stabilizers G Levelers H Fully Shrouded Flywheel I Transport Rollers J Power Connector K Water Bottle Holder L MP3 Input M USB Port N Contact Heart Rate (CHR) Sensors - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 17
Console Features The Console provides important information about your workout and lets you control the resistance levels while you exercise. The Console features the Schwinn Dual Track™ display with touch control buttons to navigate you through the exercise programs. Resistance Level Quick Buttons - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 18
quickly during a workout Achievement Indicator Lights- when a workout result is reviewed, the achievement indicator light will activate. Schwinn Dual Track™ Display the current User. These Heart Rate Zones can be used as a workout guide for a certain target zone (anaerobic, aerobic, or fat burn). - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 19
the total operational time of the machine. Note: If a Quick Start workout is performed for more than 99 minutes and 59 seconds (99:59), the units "Console Setup Mode" section in this manual. Level The LEVEL display shows the current resistance level in the workout. RPM The RPM display field shows - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 20
Contact Heart Rate Sensors Contact Heart Rate (CHR) sensors send your heart rate signals to the Console. The CHR sensors are the stainless steel parts of the Handlebars. To use, put your hands comfortably around the sensors. Be sure that your hands touch both the top and the bottom of - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 21
your optimal target rate may be higher or lower. Consult your physician for your individual target heart rate zone. Note: As with all exercises and fitness regimens, always use your best judgment when you increase your exercise time or intensity. Heart Rate BPM (beats per minute) 250 200 150 100 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 22
move the seat down on the upright bike. If your leg is bent too much, move the seat up. ! Step off the bike before you adjust the seat. to ensure maximum Pedal efficiency. Pedal straps can be left in position for subsequent workouts. Power-Up / Idle Mode The Console will enter Power-Up / Idle Mode - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 23
level. The default Manual resistance level is 4. The time will count up from 00:00. Note: If a Manual workout is performed for more than 99 . The User profiles automatically record the workout results for each workout, and allow the workout data to be reviewed. The User profile stores the following - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 24
display shows the EDIT LOWER DISPLAY prompt. This option allows you to customize which Workout Values are displayed during a workout. The Lower Display will show all of the workout values, with the active Workout Value flashing. The Upper Display shows the active value setting: "ON" or "OFF". Push - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 25
screen. Changing Resistance Levels Push the Resistance Level Increase() or Decrease() buttons to change the resistance level at any time in a workout program. To rapidly change the resistance level, push the desired Resistance Level Quick Button. The Console will adjust to the selected resistance - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 26
Console will use the Age and Weight values for the selected User Profile to calculate the Fitness Score. Start to workout and hold the Heart Rate Sensors. When the test starts, the intensity of the workout slowly increases. This means you will work harder, and as a result, your heart rate increases - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 27
of messages that change every 4 seconds: - WORKOUT PAUSED - PEDAL TO CONTINUE (if a bike) / STRIDE TO CONTINUE (if an elliptical) - PUSH END TO STOP During a paused workout, you can use the Increase/Decrease buttons to move through the result channels manually. 1. Stop pedaling and push the PAUSE - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 28
GOAL TRACK Statistics (and Achievements) The statistics from every workout are recorded to a User Profile. The Schwinn Dual Track™ Console shows the Goal Track workout Statistics on the Lower Display in three channels: a.) TIME (total), DISTANCE (total), and CALORIES (total) b.) SPEED (average - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 29
have been reset. 10. Push GOAL TRACK to return to the Power-Up screen. When a User performs a workout that surpasses the "LONGEST WORKOUT" or "CALORIE RECORD" of the previous workouts, the Console will congratulate with an audible sound and tell the User the new achievement. The corresponding - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 30
on/ off), or see maintenance statistics (Error Log and Run Hours - for service technician use only). 1. Hold down the PAUSE/END button and Right button together with the current setting. Push the Increase/Decrease buttons to change between "BIKE" and Elliptical ("ELIP"). 9. Push OK to set. 10. The - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 31
MAINTENANCE Read all maintenance instructions fully before you start any repair work. In some for loose, broken, damaged, or worn parts. Do not use if found in this condition. Repair or replace all parts at the first sign of wear or damage. After each workout, use a damp cloth to wipe your - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 32
Maintenance Parts A K J L A DD EE M C R N B G O H I P Q S T J U D E V F BB CC Y AA J D Z X W C A Console B Console Mast C Pedals D Crank Arms E Left Shroud F Power Inlet G Right Shroud H Top Shroud I Mast Gasket J Data Cable K Handlebars 32 L - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 33
Troubleshooting Condition/Problem No display/partial display/ unit will not turn on Things cream) can help make better conduct. These are available on the web or at medical or some larger fitness stores. If tests reveal no other issues, Handlebars should be replaced. All wires in cable should be - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 34
Condition/Problem Unit rocks/does not sit level Pedals loose/unit difficult to pedal necessary. Replace if there is any damage to the sensor or the connecting wire. Adjust levelers until bike is level. Check surface under unit Check pedal to crank arm connection Check pedal to crank arm connection - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 35
, (Assembly, Owner's Manuals, etc.). • Product must be used exclusively for the purpose intended. • Notify Nautilus within 30 days after detecting an issue with the Product. • Install replacement parts or components in accordance with any Nautilus instructions. • Perform diagnostic procedures with - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 36
2 years • Electronics 1 year • Labor 90 days (Labor support does not include the installation of replacement parts involved in the initial product assembly and preventative maintenance services.) What You Must Do • To arrange for warranty service, call 1-800-4-MY-HOME®. What Is Not - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 37
37 - Schwinn Journey 1.0 Upright Bike | Assembly and Owner's Manual - Page 38
Nautilus® 8002150.082113.E Bowflex® Schwinn® EN Universal®
ASSEMBLY MANUAL / OWNER’S MANUAL
Manual en Español Latino Americano:
http://www.schwinnfitness.com
130 /
1.0