Seagate ST800FM0022 Pulsar.2 SAS Product Manual

Seagate ST800FM0022 Manual

Get Seagate ST800FM0022 PDF manuals and user guides View all Seagate ST800FM0022 manuals
Add to My Manuals
Save this manual to your list of manuals

Seagate ST800FM0022 manual content summary:

  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 1
    Product Manual Pulsar®.2 SAS Standard Models ST800FM0002 ST800FM0032 ST400FM0002 ST400FM0042 ST200FM0002 ST200FM0042 ST100FM0002 ST100FM0052 Self-Encrypting Drive Models ST800FM0012 ST800FM0042 SED FIPS140-2 Models ST800FM0022 100666271 Rev. C March 2013
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 2
    Technology LLC. Call 877-PUB-TEK1 (877-782-8351) to request permission. When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer's operating system may use a different standard of measurement and report a lower
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 3
    5.2 ENDURANCE MANAGEMENT 14 SERVICE 15 5.3.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) . . . . 15 5.3.2 Preventive maintenance 15 5.3.3 Hot plugging the drive 15 5.3.4 S.M.A.R.T 15 5.3.5 Thermal monitor 16 5.3.6 Drive Self Test (DST 17 PULSAR.2 SAS PRODUCT MANUAL
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 4
    AUTHENTICATED FIRMWARE DOWNLOAD 36 POWER REQUIREMENTS 36 SUPPORTED COMMANDS 36 SANITIZE - CRYPTOGRAPHIC ERASE 36 REVERTSP 36 SANITIZE FEATURE SET ON SED DRIVES 36 9.0 DEFECT AND ERROR MANAGEMENT 37 9.1 DRIVE INTERNAL DEFECTS/ERRORS 37 9.2 DRIVE ERROR RECOVERY PROCEDURES 38 9.3 SAS SYSTEM
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 5
    DRIVE MOUNTING 41 10.4 GROUNDING 41 11.0 INTERFACE REQUIREMENTS 42 11.1 SAS FEATURES 42 11.1.1 Task management functions 42 11.1.2 Task management responses 42 11.2 11.3 DUAL PORT SUPPORT 42 SCSI COMMANDS SUPPORTED 11.7 ADDITIONAL INFORMATION 58 PULSAR.2 SAS PRODUCT MANUAL, REV. C III
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 6
    output operations per second 28 Temperature check point location - 15mm drives 29 Temperature check point location - 7mm drives 29 Recommended mounting 30 Mounting configuration dimensions (800GB models 32 detail 55 SAS transmitters and receivers 57 PULSAR.2 SAS PRODUCT MANUAL, REV. C IV
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 7
    www.seagate.com/about/contact-us/technical-support/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers Warranty terms will vary based on type of warranty chosen: "Managed Life" or "Usage Based". Consult
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 8
    your Field Applications Engineer (FAE) or our global support services group as shown in See "Seagate Technology Support Services" on page 1. Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models. Standard models Standard SED models FIPS 140
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 9
    noted in the appropriate sections of this manual and the Seagate SAS Interface Manual, part number 100293071. The drives are recognized in accordance with UL enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure, shielded cables should be used, with the
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 10
    Framework requirements of Australia's Spectrum Management Agency (SMA). Korean KCC If these drives have the Korean Communications Commission ( of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers regarding MANUAL, REV. C 4
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 11
    by the China RoHS MCV Standard. 2.2 REFERENCE DOCUMENTS SCSI Commands Reference Manual Seagate part number: 100293068 SAS Interface Manual Seagate part number: 100293071 ANSI SAS Documents SFF-82232.5" Drive Form Factor with Serial Connector SFF-8460HSS Backplane Design Guidelines SFF
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 12
    channels • Power loss data protection • Thin Provisioning with Block Unmap Support • Silent operation • Lifetime Endurance Management (available on certain models) Pulsar.2 SAS Self-Encrypting Drive models have the following additional features: • Automatic data encryption/decryption • Controlled
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 13
    Drive) models. 3.4 RELIABILITY • Annualized Failure Rate (AFR) of 0.44% • Mean time between failures (MTBF) of 2,000,000 hours • Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.) • "Managed product planning in one of two modes: MANUAL, REV. C 7
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 14
    Product Configuration Non-SED SED LBPME Supported Supported LBPRZ Supported Not Supported A logical block provisioning management enabled (LBPME) bit set to one indicates that the logical unit implements logical block provisioning management. An LBPME bit set to zero indicates that the logical
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 15
    to any device which supports LBA unmapping. In SCSI devices, umapped LBAs are defined as part of the Thin Provisioning model. Support of the Thin permitted on a locked band. Table 3 PI and SED Drive Configuration PI Setting PROT_EN bit LBPME bit LBPRZ bit PI Check Requested DATA Returned
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 16
    SAS physical interface" and the SAS Interface Manual (part number 100293071) for additional timing 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are the most flexibility for the device to manage the flash medium to maximize endurance.
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 17
    4.2.3 Performance Table 6 Performance (Managed Life Warranty) NOTE S Maximum Burst Queue Depth = 32, Sequentially Preconditioned drive, using IOMeter 2006.7.27. [2] Testing performed at Queue Depth = 32, Randomly Preconditioned drive, using IOMeter 2006.7.27. [3] .2 SAS PRODUCT MANUAL, REV. C 11
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 18
    support Lifetime Endurance Management driver limitations. It is not the intent of this manual drive that makes use of a drive buffer storage area where the data to be written to the medium is stored while the drive drive does not overwrite data the drive may to force the drive to write all cached
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 19
    the following: • The drive is operated in accordance with this manual using DC power as defined in paragraph 6.3, "DC power requirements." • Errors caused by host system failures are excluded from error rate computations. • Assume random data. • Default OEM error recovery settings are applied. This
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 20
    up faster than other locations. Wear Leveling is automatically managed by the drive and requires no user interaction. The Seagate algorithm the Thin Provisioning feature set. Use of the UNMAP command reduces the Write Amplification Factor of the drive during housekeeping tasks such MANUAL, REV. C 14
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 21
    be used to enhance the service life of the drive. Section 10.2 provides data as the drive performs normal read and write operations. When the PERF bit is set, the drive is considered to scheduled interrupt is in one hour. An application can interrogate the drive through the host to MANUAL, REV. C 15
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 22
    (1Ch). Subject to the reporting method. For example, if the MRIE is set to one, the firmware will issue to the host an 01-5D00 sense code. The determine if the warning is due to the temperature exceeding the drive threatening temperature or the user-specified temperature. This feature is controlled
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 23
    error during either of these tests, it reports a "diagnostic failed" condition. If the drive fails the test, remove it from service and return it to Seagate for service. 5.3.6.1 DST failure definition The drive will present a "diagnostic failed" condition through the self-tests results value of the
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 24
    the drive drive set to the same value as sent in the DST command 2. The Self-Test Results Value field is set to Fh 3. The drive Support Services" on page 1 for warranty information. Warranty terms will vary based on type of warranty chosen: "Managed drive in a non-approved container voids the drive
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 25
    drive. 6.1 POWER SPECIFICATIONS The drive drives are listed in the tables beginning on page 21. Typical power measurements are based on an average of drives drive reaches operating condition and can process media access commands. • Peak operating mode During peak operating mode, the drive drive
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 26
    3σ 0.62 0.46 3σ 1.01 0.76 DC 0.48 0.51 3σ 0.52 0.55 3σ 0.85 1.13 POWER (W) 4.38 4.65 5.93 6.27 9.29 9.68 8.18 8.62 8.52 9.20 PULSAR.2 SAS PRODUCT MANUAL, REV. C 20
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 27
    3σ 0.60 0.32 3σ 1.00 0.59 DC 0.46 0.44 3σ 0.52 0.48 3σ 0.91 1.14 POWER (W) 3.49 3.81 4.75 5.07 7.63 8.12 6.47 6.84 7.58 8.36 PULSAR.2 SAS PRODUCT MANUAL, REV. C 21
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 28
    3σ 0.59 0.29 3σ 0.80 0.57 DC 0.47 0.41 3σ 0.51 0.42 3σ 0.76 0.95 POWER (W) 3.47 3.69 4.68 5.15 7.27 7.59 6.11 6.43 7.27 7.59 PULSAR.2 SAS PRODUCT MANUAL, REV. C 22
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 29
    consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device. 4. Parameters, other than start, are measured after a 10-minute warm up. PULSAR.2 SAS PRODUCT MANUAL, REV. C 23
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 30
    allowed noise values given below are peak-to-peak measurements and apply at the drive power connector. +5v = 250 mV pp from 100 Hz to 20 MHz 20 MHz to 80 MHz. 6.3.2 Power sequencing The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 31
    Figure 2. Current profiles for 400GB models Figure 3. Current profiles for 200GB models PULSAR.2 SAS PRODUCT MANUAL, REV. C 25
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 32
    Figure 4. Current profiles for 100GB models PULSAR.2 SAS PRODUCT MANUAL, REV. C 26
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 33
    write operations, refer to the following I/O rate curve (see Figure 6). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total is 3.47 watts (11.84 BTUs per hour). PULSAR.2 SAS PRODUCT MANUAL, REV. C 27
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 34
    on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C). Note. To maintain optimal performance drives should be run at nominal case temperatures. PULSAR.2 SAS PRODUCT MANUAL, REV. C 28
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 35
    configuration, and perform random write/read operations. After the temperatures stabilize, measure the case temperature of the drive. See Figure 9 and 10 for temperature checkpoint. b. Non-operating -40° to 158°F (-40 to +40,000 feet (-60.96 to +12,192 meters) PULSAR.2 SAS PRODUCT MANUAL, REV. C 29
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 36
    drive movement. The limits of shock and vibration defined within this document are specified with the drive normal The drive, as drives and integrated drives. The drive finished drive bulk packs instructions are printed on the bulk pack carton for minimum drive quantities and proper drive
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 37
    apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive shall not incur physical damage or degraded performance as a result of . 6.5.7 Electromagnetic susceptibility See Section 2.1.1.1. PULSAR.2 SAS PRODUCT MANUAL, REV. C 31
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 38
    6.6 MECHANICAL SPECIFICATIONS Refer to Figure 12 or 13 for detailed mounting configuration dimensions. See Section 10.3, "Drive mounting." Weight: 0.353 pounds 160 grams Note. These dimensions conform to the Small Form Factor Standard documented in SFF-8201 and SFF-8223 found at
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 39
    Weight: 0.220 pounds 100 grams Note. These dimensions conform to the Small Form Factor Standard documented in SFF-8201 and SFF-8223 found at www.sffcommittee.org Figure 13. Mounting configuration dimensions (400, 200 & 100GB models) PULSAR.2 SAS PRODUCT MANUAL, REV. C 33
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 40
    testing. Seagate Enterprise SED The SEDs referenced in this Product Manual have been validated by CMVP and have been thoroughly tested of an operator to assume a specific role and perform a corresponding set of services. Figure 14. Example of FIPS tamper evidence labels. Note. Image is
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 41
    the drive in the appropriate command payloads. 8.1 DATA ENCRYPTION Encrypting drives use one These act as gatekeepers to the drive security services. Security-related commands will not be 8.2.3 Default password When the drive is shipped from the factory, all passwords are set to the value of MSID.
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 42
    it was written with one key and will be read using a different key. Since the drive overwrites the old key with the new one, and keeps no manually read from the drive label or scanned in via the 2D barcode. 8.12 SANITIZE FEATURE SET ON SED DRIVES The drive shall support the Sanitize Feature Set
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 43
    management routines. 9.1 DRIVE INTERNAL DEFECTS/ERRORS During the initial drive supported by the drive are described in the SAS Interface Manual. Also, more information on the drive Error Recovery philosophy is presented in the SAS Interface Manual. The drive more than one flash controller.
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 44
    drive. Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a role in systems error management . BMS interrupts immediately to service host commands from the interface setting from the Seagate factory. PULSAR.2 SAS PRODUCT MANUAL, REV. C 38
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 45
    drives are physically formatted to 520 byte LBA's that store 512 bytes of customer data with 8 bytes of Protection Information appended to it. The advantage of PI is that the Protection Information bits can be managed at the HBA and HBA driver level. Allowing a system that typically does not support
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 46
    jumpers on the drive. SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive drive in a non-backplane host system, connecting the drive instructions provided by the host system. This connects the drive the drive should
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 47
    are created by one or more drive in the host equipment. Increased radiated emissions may result if designers do not provide the maximum surface area ground connection between system ground and drive ground. This is the system designer's and integrator's responsibility. PULSAR.2 SAS PRODUCT MANUAL
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 48
    section lists the SAS-specific features supported by Pulsar.2 drives. 11.1.1 Task management functions Table 14 lists the SAS task management functions supported. Table 14 SAS task management functions supported TASK NAME SUPPORTED Abort Task Yes Abort task set Yes Clear ACA Yes Clear
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 49
    ) Device Behavior page (C3h) Device Identification page (83h) Extended Inquiry Data page (86h) Firmware Numbers page (C0h) Jumper Settings page (C2h) Power Conditions page (8Ah) Supported Vital Product Data page (00h) Thin Provisioning page (B2h) Unit Serial Number page (80h) Vendor Unique page
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 50
    LONG (10) COMMAND CODE 15h 55h 1Ah 5Ah 5Eh 5Fh 34h 08h 28h A8h 88h 7Fh/0009h 3Ch 25h 9Eh/10h 37h B7h 3Eh SUPPORTED Y Y N Y Y Y Y Y Y Y Y [3] Y Y [3] Y Y Y Y N Y Y N Y Y Y N Y Y N Y Y Y N Y Y Y Y N Y Y Y (non-SED drives only) Y Y Y Y Y (non-SED drives only) PULSAR.2 SAS PRODUCT MANUAL, REV. C 44
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 51
    10) DPO bit FUA bit WRITE (12) PULSAR.2 SAS PRODUCT MANUAL, REV. C COMMAND CODE 9Eh/11h 07h 1Ch 17h 57h 03h 16h 56h 01h 48h ---/03h A2h B5h 0Bh 2Bh 1Dh 1Bh 35h 91h 00h 42H 2Fh AFh AFh 7Fh/000Ah 0Ah 2Ah AAh SUPPORTED Y (non-SED drives only) Y Y Y N Y Y Y Y Y Y Y Y Y N Y Y N Y Y (SED models only) N
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 52
    can result in firmware corruption. This usually makes the drive inoperable. [3] Reference MODE SENSE command 1Ah for mode pages supported. [4] Y = Yes. Command is supported. N = No. Command is not supported. A = Support is available on special request. PULSAR.2 SAS PRODUCT MANUAL, REV. C 46
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 53
    that the drive should return to the initiator per the format given in the SAS Interface Manual. Table 17 Copyright year (changes with actual year). ** SCSI Revision support. See the appropriate SPC release documentation for definitions. PP 30 46 4D 30 30 31 32 ST800FM0022 53 54 38 30 30 46 4D
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 54
    drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive is not changeable. Since all of the bits in byte 02 are ones, all of these bits are changeable. The changeable values list can only
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 55
    Table 18 MODE SENSE data for 800GB drives MODE DATA HEADER: 01 3e 00 10 01 00 00 10 BLOCK DESCRIPTOR: 00 00 00 00 5d 26 ce b0 00 00 00 00 00 00 00 00 DEF 80 06 00 80 00 00 00 00 CHG 80 06 b7 80 00 00 00 00 PULSAR.2 SAS PRODUCT MANUAL, REV. C 49
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 56
    Table 19 MODE SENSE data for 400GB drives MODE DATA HEADER: 01 3e 00 10 01 00 00 10 BLOCK DESCRIPTOR: 00 00 00 00 2e 93 90 b0 00 00 00 00 00 00 00 00 DEF 80 06 00 80 00 00 00 00 CHG 80 06 b7 80 00 00 00 00 PULSAR.2 SAS PRODUCT MANUAL, REV. C 50
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 57
    Table 20 MODE SENSE data for 200GB drives MODE DATA HEADER: 01 3e 00 10 01 00 00 10 BLOCK DESCRIPTOR: 00 00 00 00 17 49 f1 b0 00 00 00 00 00 00 00 00 DEF 80 06 00 80 00 00 00 00 CHG 80 06 b7 80 00 00 00 00 PULSAR.2 SAS PRODUCT MANUAL, REV. C 51
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 58
    Table 21 MODE SENSE values for 100GB drives MODE DATA HEADER: 01 3e 00 10 01 00 00 10 BLOCK DESCRIPTOR: 00 00 00 00 0b a5 22 30 00 00 00 00 00 00 00 00 DEF 80 06 00 80 00 00 00 00 CHG 80 06 b7 80 00 00 00 00 PULSAR.2 SAS PRODUCT MANUAL, REV. C 52
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 59
    17 Table 23 Miscellaneous status SUPPORTED STATUS Y Good Y Check condition Y Condition met/good Y Busy Y Reservation conflict Y Task set full N ACA active aspects of Seagate's SAS drives are provided in the SAS Interface Manual. Figure 17. Physical interface PULSAR.2 SAS PRODUCT
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 60
    ) 1.27 (6X) 5.08 B 0.84 0.05 (22X) 0.15 B 4.90 0.08 P15 Figure 18. SAS device plug dimensions P1 S1 S7 CL OF DATUM B PULSAR.2 SAS PRODUCT MANUAL, REV. C 54
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 61
    DATUM A 0.03 1.23 0.05 65 30 0.08 0.05 Detail 2 1.90 0.08 Figure 19. SAS device plug dimensions (detail) 2.40 0.08 0.10 A D SECTION B - B PULSAR.2 SAS PRODUCT MANUAL, REV. C 55
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 62
    B_out Diff output pair S13* +Port B_out S14 Port B Ground * - Short pin to support hot plugging NC - No connection in the drive. PIN SIGNAL NAME SIGNAL TYPE P1* NC (reserved 3.3Volts) P2* NC (reserved 3.3Volts) charge P14* 12 Volts P15* 12 Volts PULSAR.2 SAS PRODUCT MANUAL, REV. C 56
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 63
    drive receives power (+5 the drive, 2 power to the drive, 2 short drive during hot plugging. 11.5 SIGNAL CHARACTERISTICS This section describes the electrical signal characteristics of the drive external to the drive. See Table 26 for the output characteristics of the LED drive signals. Table 26 LED drive
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 64
    Link, Transport, and Applications layers of the SAS interface, refer to the Seagate SAS Interface Manual, part number 100293071. For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual, part number 100293068. PULSAR.2 SAS PRODUCT
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 65
    PULSAR.2 SAS PRODUCT MANUAL, REV. C INDEX class B limit 3 clear ACA function 42 clear task set function 42 CMVP 34 commands supported 43 condensation 29 dimensions 32 drive 31 drive characteristics 10 drive failure 15 Drive Locking 35 drive mounting 32, 41 drive select 56 dual port support 42 E
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 66
    management 42 not supported, code 05 guide 5 interface commands supported 43 error rate 13 errors 13 illustrated 53 physical 53 requirements 42 internal defects/errors 37 internal drive characteristics 10 J jumpers 40 L LBPME bit 9 LBPRZ bit 9 Lifetime Endurance Management support support Task set full
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 67
    RoHS 4, 5 S safety 3 Sanitize 36 sanitize feature set 36 SAS interface 56 physical interface 53 task management functions 42 SAS documents 5 SAS Interface Manual 3, 5 SAS-2 Specification 58 SCSI interface commands supported 43 Seagate Technology Support Services 1 Secure ID 35 Security Protocol In
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 68
    management response codes 42 Function complete 00 42 Function not supported 05 42 Function reject 04 42 task set full status 53 TCG 35 temperature 29, 40 limits 28 non-operating 29 regulation 3 See also cooling terminate task function 42 Thin Provisioning 8 transmitters 57 transporting the drive
  • Seagate ST800FM0022 | Pulsar.2 SAS Product Manual - Page 69
    Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Product Manual
Pulsar
®
.2 SAS
100666271
Rev. C
March 2013
Standard Models
ST800FM0002
ST800FM0032
ST400FM0002
ST400FM0042
ST200FM0002
ST200FM0042
ST100FM0002
ST100FM0052
Self-Encrypting Drive Models
ST800FM0012
ST800FM0042
SED FIPS140-2 Models
ST800FM0022