Seagate SV35 Series SV35 Series PATA Product Manual

Seagate SV35 Series Manual

Get Seagate SV35 Series PDF manuals and user guides View all Seagate SV35 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Seagate SV35 Series manual content summary:

  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 1
    Product Manual SV35 Series PATA ST3500641AV ST3250824AV ST3160812AV 100415205 Rev. B August 2007
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 2
    are registered trademarks of Seagate Technology LLC in the United States and/or other countries. SV35 Series, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or Seagate reserves the right to change, without notice, product offerings or specifications.
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 3
    4.1 ATA interface signals and connector pins 29 4.1.1 Supported ATA commands 30 4.1.2 Identify Device command 33 4.1.3 Set Features command 37 4.1.4 S.M.A.R.T. commands 38 4.1.5 Streaming feature set support 39 5.0 Seagate Technology support services 51 SV35 Series Product Manual, Rev. B i
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 4
    ii SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 5
    Breather filter hole location 24 Master/slave jumper settings 25 Ultra ATA cable connectors 26 Mounting dimensions-top, side and end view 27 I/O pins and supported ATA signals 29 SV35 Series Product Manual, Rev. B iii
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 6
    iv SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 7
    1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® SV35 model drives: • ST3500641AV • ST3250824AV • ST3160812AV These drives provide the following key features: • Specifically designed for surveillance DVRs. Supports a subset of
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 8
    2 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 9
    under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following models: ST3500641AV ST3250824AV ST3160812AV 2.1 Specification summaries The specifications listed in the following three tables are
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 10
    Drive specification Formatted Gbytes (512 bytes/sector)* Guaranteed sectors Bytes per sector Default sectors per track Default read/write heads Default cylinders Recording density, KBPI (kbits/in max) Track density, KTPI (ktracks/in max) Areal density, (Gbits/in2 max) Spindle speed (RPM) Internal
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 11
    the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 12
    Drive specification Formatted Gbytes (512 bytes/sector)* Guaranteed sectors Bytes per sector Default sectors per track Default read/write heads Default cylinders Recording density, KBPI (kbits/in max) Track density, KTPI (ktracks/in max) Areal density, (Gbits/in2 max) Spindle speed (RPM) Internal
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 13
    the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 14
    Drive specification Formatted Gbytes (512 bytes/sector)* Guaranteed sectors Bytes per sector Default sectors per track Default read/write heads Default cylinders Recording density, KBPI (kbits/in max) Track density, KTPI (ktracks/in max) Areal density, (Gbits/in2 max) Spindle speed (RPM) Internal
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 15
    the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 16
    logical geometry Cylinders 16,383 Read/write heads 16 Sectors per track 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n-1, where n is the number of guaranteed sectors as defined above. 10 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 17
    Areal density (Gbits/inch2 max) ST3500641AV and ST3250824AV ST3160812AV Spindle speed (RPM) (± 0.2%) Internal data-transfer rate (Mbits/sec max) ST3500641AV ST3250824AV and 83.0 100 (Ultra DMA mode 5) 16 MBytes (16,384 kbytes) 8 Mbytes (8,192 kbytes) SV35 Series Product Manual, Rev. B 11
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 18
    are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications. 2.7 Start/stop times Power-on to Ready (sec) Standby to Ready (sec) Ready to spindle stop (sec) 16 16 (max) 10 (max) 12 SV35 Series Product Manual, Rev
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 19
    2.8 Power specifications The drive receives DC power (+5V and +12V) through a four-pin standard drive power connector. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 13. Typical power measurements are based on an average of drives tested, under nominal
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 20
    12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise tolerance Voltage tolerance (including noise): 5V ± 5% 12V ± 10% 14 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 21
    power management through the system setup program. The drive features the following power-management modes: Power parameters intact. • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer necessary. SV35 Series Product Manual, Rev. B 15
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 22
    2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual to 3,048 m (-200 ft. to 10,000+ ft.) -60.96 m to 12,192 m (-200 ft. to 40,000+ ft.) 16 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 23
    specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock These drives comply with the performance performance vibration specifications assume that performance performance
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 24
    defined by the following equation: (Number of seeks per second = 0.4 / (average latency + average access time) Drive acoustics, sound power Idle Operational, DVR (Digital Video Recorder) seeks 2.46 bels (typ) 2.65 bels (max) 2.8 bels (typ) 2.9 bels (max) 18 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 25
    in the following table: Table 5: Radio frequency environments Test Electrostatic discharge Description Performance level Contact, HCP, VCP: ± 4 kV; bits read, max. Annualized Failure Rate (AFR)
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 26
    (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment ( verification or certification of the device is required. 20 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 27
    tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power 's instructions, Interference Problems. testing, and an internal auditing process to ensure compliance with all standard operating procedures. SV35 Series Product Manual
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 28
    oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any be extended by replacing materials near circuitry with sulfide-free alternatives. 22 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 29
    mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. SV35 Series Product Manual,
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 30
    this hole is covered, sealed, or penetrated by any object, drive reliability may be compromised and could lead to permanent damage-doing so voids the warranty. 24 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 31
    the drive, you can: • Update the BIOS • Use third- power on. The ATA Set Features subcom- mand "F1H Report Full Capacity Available" causes Identify Data words 60 and 61 to report the full capacity. See Section 4.1.3 on page 37 for more details on the Set Features command. SV35 Series Product Manual
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 32
    gray connector MCoothmeprbuotearrd to the slave. Figure 5 Ultra ATA cable connectors Note. The drive supports both host and drive cable detection. The host detects the 80-conductor cable by sampling a drive interface cable that is more than 18 inches long. 26 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 33
    Notes: 1. Dimensions are shown in inches (mm). 2 Dimensions per SFF-8301 specification. 1.028 max (26.11) 3 x 0.25 0.010 (6.35 0.037) both sides 1.122 0.02 . fastener penetration. 3 threads minimum engagement. Recommended case temperature measurement location SV35 Series Product Manual, Rev. B 27
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 34
    28 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 35
    signals and connector pins Figure 7 summarizes the signals on the ATA interface connector that the drive supports. For a detailed description of these signals, refer to the Draft ATA-7 Standard. Drive pin - 39 Figure 7 I/O pins and supported ATA signals SV35 Series Product Manual, Rev. B 29
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 36
    details and subcommands used in the S.M.A.R.T. implementation. Table 6: Supported ATA commands Command name Check Power Mode Configure Stream Device Configuration Freeze Lock Device Configuration Identify Device 95H or E1H 91H E4H C8H 25H C9H 2FH C4H 29H F8H 30 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 37
    Sectors 20H Read Sectors Extended 24H Read Sectors Without Retries 21H Read Stream DMA EXT 2AH Read Verify Sectors 40H Read Verify Sectors Extended 42H Read Verify Sectors Enable Operations B0H / D8H S.M.A.R.T. Execute Offline B0H / D4H SV35 Series Product Manual, Rev. B 31
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 38
    Read Log Sector S.M.A.R.T. Return Status S.M.A.R.T. Save Attribute Values S.M.A.R.T. Write Log Sector Standby Standby Retries Write Log Extended Write Multiple Write Multiple Extended Write Sectors Write Sectors Without Retries Write Sectors Extended Write Stream DMA EXT Command code (in hex) B0H
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 39
    Maximum sectors per interrupt on Read multiple and Write 8010H multiple (16) 48 Reserved 0000H 49 Standard Standby timer, IORDY supported and may be disabled 2F00H 50 ATA-reserved 0000H 51 PIO data-transfer cycle timing mode 0200H 52 Retired 0200H SV35 Series Product Manual, Rev
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 40
    of current logical sectors per logical track Current capacity in sectors Number of sectors transferred during a this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes). Drives with capacities over 137 number Command sets supported Command sets supported Command sets support extension Command sets
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 41
    DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 88 0 Ultra DMA mode 0 is supported. SV35 Series Product Manual, Rev. B 35
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 42
    1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 8 Ultra DMA mode 0 is currently active. 9 Ultra DMA mode above VIH 0 = 40-conductor cable detected, CBLID below VIL 36 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 43
    supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows: 02H Enable write cache (default). 03H Set transfer mode (based on value in Sector Count register). Sector
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 44
    self-test ( specific D8H S.M.A.R.T. Enable Operations D9H S.M.A.R.T. Disable Operations DAH S.M.A.R.T. Return Status Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register. 38 SV35 Series Product Manual
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 45
    to 0, the bit will clear. Word 95 (Stream Minimum Request Size) World 95 contains the number of sectors that provide optimum performance in a streaming environment. This number shall be a power of two, with a minimum of eight sectors (4096 bytes). The starting LBA value for each streaming command
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 46
    but there may be an impact on performance due to the unknown time required be a multiple of the minimum number of sectors per transfer, as should the starting LBA of the device in an error condition is vendor specific. Write Continuous bit If the Write Continuous SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 47
    INTRQ for command completion. SECTOR COUNT REGISTER FIELD DESCRIPTIONS Current The size of an Allocation Unit in sectors (bits 7:0). Previous The size of an Allocation Unit in sectors (bits 15:8) DEVICE REGISTER FIELD DESCRIPTIONS Dev The selected device. SV35 Series Product Manual, Rev. B 41
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 48
    65536 sectors as specified in the Sector Count register. A value of 0000h in the Sector Count register requests 65536 sectors. The to fulfill the host's requested transfer size. The implementation of the padding is vendor specific. If the drive is unable to SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 49
    Write). If the Default Command Completion Time Limit is 0, or no previous Configure Stream command was defined for this Stream type, the result is vendor specific. The time is measured from the write of the command register to the final INTRQ for command completion
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 50
    7 6 5 4 3 2 1 0 Error ICRC UNC N/A IDNF N/A ABRT N/A CCTO Sector Count HOB = 0 Length of Stream Error (7:0) LBA Low HOB = 1 Length of Stream Error bit shall be set to 1 if this command is not supported. ABRT may be set to 1 if the device is SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 51
    be the address of the first sector in error, and the Sector Count registers shall contain the number of consecutive sectors that may contain errors. DRQ 0 This bit shall be set to 0. ERR 1 This bit shall be set to 1 if an Error register bit is set to 1. SV35 Series Product Manual, Rev. B 45
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 52
    to specify to the device that additional actions need to be performed prior to the completion of the command if the required bits Ignored r 2 1 0 Ignored Sector Count Previous Current Command Completion Time Limit (7:0) Sector count Previous LBA Low, Mid, SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 53
    defined for this Stream ID, the result is vendor specific. The time is measured from the write of 7 6 5 4 3 2 1 0 Error ICRC N/A N/A IDNF N/A ABRT N/A CCTO Sector Count HOB = 0 Length of Stream Error (7:0) LBA Low HOB = 1 Length of Stream SV35 Series Product Manual, Rev. B 47
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 54
    shall be set to 1 if this command is not supported. ABRT may be set to 1 if the device Sector Number registers shall be the address of the first sector in error, and the Sector Count registers shall contain the number of consecutive sectors service a command. 48 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 55
    caching is allowed, the actuator could be busy servicing a cached write at virtually any time. the host's time limit allows, the drive will perform internal defect management on any defective sectors encountered. If the drive runs out of time during types. SV35 Series Product Manual, Rev. B 49
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 56
    50 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 57
    by email for your questions. Presales Support: [email protected] Technical Support: [email protected] Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 58
    East and Africa, go to the "Contact Us" page on www.seagate.com. Asia/Pacific Support Services For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific, go to the "Contact Us" page on www.seagate.com. 52 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 59
    cycles 19 Cylinders 10 SV35 Series Product Manual, Rev. B D Data Defense 1 data-transfer rates 1 DC power 13 Default logical 12 drive monitoring 1 drive self-test 1, 38 DST 38 E electrical enclosures 21 Environmental protection 21 environmental specifications 16 EPRML 11 error-correction algorithms
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 60
    26 P physical characteristics 12 pins 29 PIO 29 power consumption 13 power dissipation 13 power management 15 power specifications 13 power-management modes 15 Power-on to Ready 12 precautions 26 preventive maintenance 19 programmable power management 15 R radiated RF immunity 19 radio and
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 61
    speed 11 Spinup 13 spinup power 13 Standby 13, 32 Standby Immediate 32 Standby mode 13, 15 Standby to Ready 12 start/stop times 12 start-stop cycles 19 static-discharge precautions 23 stop times 12 subassembly 20 support services 51 surge immunity 19 T technical support services 51 temperature 16
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 62
    56 SV35 Series Product Manual, Rev. B
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 63
  • Seagate SV35 Series | SV35 Series PATA Product Manual - Page 64
    Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100415205, Rev. B, Printed in U.S.A.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Product Manual
SV35 Series PATA
100415205
Rev. B
August 2007
ST3500641AV
ST3250824AV
ST3160812AV