Seagate Savvio 15K Savvio 15K.3 SAS Product Manual

Seagate Savvio 15K Manual

Get Seagate Savvio 15K PDF manuals and user guides View all Seagate Savvio 15K manuals
Add to My Manuals
Save this manual to your list of manuals

Seagate Savvio 15K manual content summary:

  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 1
    Product Manual Savvio® 15K.3 SAS Standard Models ST9300653SS ST9146853SS Self-Encrypting Drive Models ST9300553SS ST9146753SS SED FIPS140-2 Models ST9300453SS ST9146653SS 100629381 Rev. D January 2012
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 2
    12 Sheets affected or comments Initial release. 26, 31, 35, 38, 41 & 50-51. fc, 2, 37 & 48. fc, 2, 4, 11-12, 18, 24-26, 31, 36, 38-40, 50, 52-53 & bc. © 2012, Seagate will not be available for data storage. Seagate reserves the right to change, without notice, product offerings or specifications.
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 3
    Contents 1.0 Seagate Technology support services 1 2.0 Scope 2 3.0 Applicable standards and reference documentation 3 3.1 Standards 3 9 4.6 Programmable drive capacity 10 4.7 Factory installed options 10 5.0 Performance characteristics 11 5.1 Internal drive characteristics 11 5.2 Seek
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 4
    RNG 39 9.4 Drive locking 39 9.5 Data bands 39 9.6 Cryptographic erase 39 9.7 Authenticated firmware download 39 9.8 Power requirements 40 9.9 Supported commands 40 9.10 Sanitize - CRYPTOGRAPHIC ERASE 40 9.11 RevertSP 40 10.0 Defect and error management 41 10.1 Drive internal defects/errors
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 5
    .5 Signal characteristics 63 12.5.1 Ready LED Out 63 12.5.2 Differential signals 64 12.6 SAS-2 Specification compliance 64 12.7 Additional information 64 Savvio 15K.3 SAS Product Manual, Rev. D iii
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 6
    iv Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 7
    operations per second 30 Location of the HDA temperature check point 31 Recommended mounting 33 Dimensions 35 Example of FIPS tamper evidence labels/seals 37 Physical interface 46 Air flow 47 Physical interface 59 SAS device plug dimensions 60 SAS device plug dimensions (detail 61 SAS
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 8
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 9
    /support/warranty_&_returns_assistance For information regarding Data Recovery Services, visit http://www.i365.com For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system For Seagate reseller portal, visit http://spp.seagate.com Savvio 15K.3 SAS Product Manual
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 10
    (FAE) or our global support services group as shown in Section 1.0. Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models. Model Number ST9300653SS ST9300553SS ST9300453SS ST9146853SS ST9146753SS ST9146653SS Self-Encrypting Drive (SED) No Yes
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 11
    must meet the requirements of Section 11.3 3.1 Standards The Savvio family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate SAS Interface Manual, part number 100293071. The drives are recognized in accordance with UL 60950-1 as tested by UL, CSA
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 12
    Printer • Mouse Although the test system with this Seagate model complies with the directives/standards, we cannot Framework requirements of Australia's Spectrum Management Agency (SMA). Korean KCC If these drives have the Korean Communications Commission ( 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 13
    effective July 2006. A number of parts and materials in Seagate products are procured from external suppliers. We rely on the declarations for all parts and materials for the disk drives documented in this publication. Current supplier declarations include 15K.3 SAS Product Manual, Rev. D 5
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 14
    3.2 Reference documents SAS Interface Manual Seagate part number: 100293071 SCSI Commands Reference Manual Seagate part number: 100293068 Self-Encrypting Drives Reference Manual Seagate part number: 100515636 ANSI SAS Documents SFF-8323 3.5" Drive Form Factor with Serial Connector SFF-8460
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 15
    The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for "Security of Data at Rest" based on the standards defined by the Trusted Computing Group (see www.trustedcomputinggroup.org). The head and disk assembly (HDA) is sealed at the factory. Air recirculates
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 16
    • Controlled access • Random number generator • Drive locking • 16 independent data bands • Cryptographic erase of user data for a drive that will be repurposed or scrapped • Authenticated firmware download 4.2 Media description The media used on the drive has an aluminum substrate coated with
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 17
    Firmware-controlled multisegmented cache designed to dynamically adjust segments for enhanced system performance • 600 MB/s maximum instantaneous data transfers • 15K RPM spindle. Average latency = 2.0 ms • Background processing of queue • Supports 778 21407E5A ST9146853SS ST9146753SS ST9146653SS
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 18
    table in the SAS Interface Manual, part number 100293071. A value of zero in the Number of Blocks field indicates that the drive will not change the number of LBAs is rounded down to the maximum capacity. 4.7 Factory installed options You may order the following items which are incorporated
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 19
    drive characteristics Drive capacity Read/write data heads Tracks per surface (total) Tracks per in Peak bits per in Areal density Internal data rate Disk rotation speed Avg rotational latency ST9300653SS ST9300553SS ST9300453SS 300 4 107,400 273,000 1601 448 1554 - 2267 15K 2.0 ST9146853SS Manual
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 20
    to or from the host. ** MiB/s x 1.048 = MB/s 5.3 Start/stop time The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied. If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 21
    . The drive keeps track of the logical block addresses of the data stored in each segment of the buffer. If the cache is enabled (see RCD bit in the SAS Interface Manual), data requested by the host with a read command is retrieved from the buffer, if possible, before any disk access is initiated
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 22
    data is cached for subsequent Read commands. If the number of write data drive. 5.5.2 Prefetch operation If the Prefetch feature is enabled, data in contiguous logical blocks on the disk , finding the requested data in the buffer is = 0 enables prefetch. The drive does not use the Max Prefetch
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 23
    errors occurring during a write. 6.1.2 Unrecoverable Errors An unrecoverable data error is defined as a failure of the drive to recover data from the media. These errors occur due to head/media or write problems. Unrecoverable data errors are only detected during read operations, but not caused
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 24
    data as transmitted by the device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss of word sync, or CRC error. 6.2 Reliability and service You can enhance the reliability of Savvio disk drives self-test fails, the drive does not respond to
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 25
    data before an actual failure occurs. Note. The drive's firmware monitors specific attributes for degradation over time but can't predict instantaneous drive on the drive interfaces. The process of measuring off-line attribute data and saving data to the disk is uninterruptable. Manual, Rev. D 17
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 26
    signals predictive failures when the drive is performing unacceptably for a period of time. The firmware keeps a running count of compliance with the SCSI standard. The drive temperature is reported in the FRU code field of mode sense data. You can use this information to SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 27
    . If the drive fails the test, remove it from service and return it to Seagate for service. 6.2.6.1 DST failure definition The drive will present a reported regardless of the number of retries required to recover the data. The following conditions are considered DST failure conditions: • Seek
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 28
    the self-test results log parameter section of the log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 parameter blocks in the log page. If there are more -test routine was interrupted by a reset condition). 20 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 29
    equipment. Product repair and return information Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids the warranty. Storage The
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 30
    drive. 7.1 PowerChoiceTM power management Drives using the CSS architecture have limited power management capability. The table below lists the supported disks not spinning) PowerChoice can be invoked using only the Start Stop Unit command for drives the drive to any supported PowerChoice mode
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 31
    enabled / disabled • Idle condition timer values (100ms increments) (default, saved, current, changeable) Power Condition Vital Product Data (VPD) Page (VPD page 0x8A) • Supported power conditions • Typical recovery time from power conditions (1ms increments) Start/Stop Cycle Counter Log Page
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 32
    1.43 1.36 0.59 0.38 0.66 0.40 1.26 1.34 0.89 0.25 0.97 0.25 1.31 0.48 1.05 0.25 1.10 0.25 1.40 0.42 24 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 33
    supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient. the drive signifies that its power-up sequence has been completed and that the drive is completes but before the drive has received the Notify reads. [7] During idle, the drive heads are relocated every 60 seconds
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 34
    to multiple drives from a common supply, careful consideration for individual drive power given below are peak-to-peak measurements and apply at the drive power connector. +5V +12V = 250 mV pp from 100 The drive does not require power sequencing. The drive protects against inadvertent writing during power-up
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 35
    7.3.3 Current profiles The +12V and +5V current profiles for the Savvio 15K.3 SAS drives are shown below. Figure 1. Current profile for 300GB models. Savvio 15K.3 SAS Product Manual, Rev. D 27
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 36
    Figure 2. Current profile for 146GB models Note: All times and currents are typical. See Tables 2 and 3 for maximum current requirements. 28 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 37
    operations, refer to the following I/O rate curve (see Figure 3). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and power vs. input/output operations per second Savvio 15K.3 SAS Product Manual, Rev. D 29
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 38
    operations, refer to the following I/O rate curve (see Figure 3). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and power vs. input/output operations per second 30 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 39
    the drive is packaged in the shipping container designed by Seagate for use with drive. HDA drive occurs. a. Operating 5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour. b. Non-operating 5% to 95% non-condensing relative humidity. Savvio 15K.3 SAS Product Manual
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 40
    ISTA and ASTM standards. Volume finished drives will be shipped from Seagate factories on pallets to minimize freight costs and ease material handling. Seagate finished drive bulk packs may be shipped individually. For less than full shipments, instructions are printed on the bulk pack carton
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 41
    mounting Note. Image is for reference only, may not represent actual drive. 7.5.4.2 Vibration a. Operating-normal The drive as installed for normal operation, shall comply with the complete specified This assumes system recovery routines are available. Savvio 15K.3 SAS Product Manual, Rev. D 33
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 42
    isolated drives and integrated drives. The drive shall not Seagate electronic drive drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate typical drives when measured according to Seagate specification 30553-001. There
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 43
    7.6 Mechanical specifications Refer to Figure 9 for detailed mounting configuration dimensions. See Section 11.3, "Drive mounting." Weight: 300GB models: 0.441 lb 146GB models: 0.426 lb 0.200 Kg 0.193 .org. in mm in mm in mm Figure 9. Dimensions Savvio 15K.3 SAS Product Manual, Rev. D 35
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 44
    testing. Seagate Enterprise SED The SEDs referenced in this Product Manual have been seals on removable covers of the module. Tamper-evident coatings or seals are placed on a cryptographic module so that the coating or seal corresponding set of services. 36 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 45
    Figure 10. Example of FIPS tamper evidence labels/seals. Note. Image is for reference only, may not represent actual drive. Savvio 15K.3 SAS Product Manual, Rev. D 37
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 46
    key is used for each of the drive's possible16 data bands (see Section 9.5). 9.2 Controlled access The drive has two security providers (SPs) called the "Admin SP" and the "Locking SP." These act as gatekeepers to the drive security services. Security-related commands will not be accepted
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 47
    and installed in another system. When the drive is shipped from the factory, the firmware download port is unlocked. 9.5 Data bands When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as the Global Data Band) which comprises LBA 0 through LBA
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 48
    Op code 48h and selecting the service action code 3 (CRYPTOGRAPHIC ERASE) 9.11 RevertSP SED models will support the RevertSP feature which erases all data in all bands on the device and returns the contents of all SPs (Security Providers) on the device to their original factory state. In order to
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 49
    Defect and error management Seagate continues to use innovative technologies to manage defects and errors. These technologies are designed to increase data integrity, perform drive self-maintenance, and validate proper drive operation. SCSI defect and error management involves drive internal defect
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 50
    even if the ARRE or AWRE bits are one. The drive will still perform data recovery actions within the limits defined by the Read Retry Count drive. Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a role in systems error management
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 51
    drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into service by the host system. On regular duty drives to rewrite the data. DAR is most effective when AWRE and ARRE are enabled-this is the default setting from the Seagate factory. With AWRE and
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 52
    to be stored on the media, but the 8 bytes will not be transferred to the host during a read command. Type 3 - Seagate products do not support Type 3. 10.8.2 Setting and determining the current Type Level A drive is initialized to a type of PI by using the format command on a PI capable
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 53
    Descriptor (VPD) page 0x86 provides bits to indicate the PI Types supported and which PI fields the drive supports checking. Note. For further details with respect to PI, please refer to SCSI Block Commands - 3 (SBC-3) Draft Standard documentation. Savvio 15K.3 SAS Product Manual, Rev. D 45
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 54
    The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (disks level) and vertical (drive on its side) orientations, which are the two preferred mounting orientations. 46 Savvio 15K.3 SAS Product Manual, Rev
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 55
    Temperature." The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disk assembly (HDA). You should confirm that adequate heat removal HDA may not represent actual product, for reference only. Savvio 15K.3 SAS Product Manual, Rev. D 47
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 56
    you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to in the drive and cannot be separated by the user. The equipment in which the drive is mounted is electrically isolating) method of mounting the drive in the host equipment. Increased
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 57
    the SAS Interface Manual (part number 100293071). 12.1 SAS features This section lists the SAS-specific features supported by Savvio drives. 12.1.1 Task management functions Table 5 lists the SAS task management functions supported. Table 5: SAS task management functions supported Task name
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 58
    Gb/s. Subject to buffer availability, the Savvio drives support: • Concurrent port transfers-The drive supports receiving COMMAND, TASK management transfers on both ports at the same time. • Full duplex-The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving frames on both
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 59
    Factory Log page (3Eh) Information Exceptions Log page (2Fh) Last n Deferred Errors or Asynchronous Events page (0Bh) Last n Error Events page (07h) Non-medium Error page (06h) Pages Supported Port page (19h) Power Condition page (1Ah) Rigid Disk Drive Geometry page (04h) Unit Attention page (00h)
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 60
    57h A0h 03h 16h 56h 01h 48h 31h 30h 32h A2h B5h 0Bh 2Bh 1Dh 33h Supported Y Y N Y N Y (non-SED drives only) Y Y Y Y Y (non-SED drives only) Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y N Y Y (SED drives only) N N N Y (SED drives only) Y (SED drives only) Y Y Y Y Y N Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 61
    loss during flash programming can result in firmware corruption. This usually makes the drive inoperable. [3] Reference Mode Sense command 1Ah for mode pages supported. [4] Y = Yes. Command is supported. N = No. Command is not supported. A = Support is available on special request. [5] Approximately
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 62
    39 33 30 30 34 35 33 53 53 ST9146853SS 53 54 39 31 34 36 38 35 33 data The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive firmware
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 63
    often several different versions of drive control firmware in the total population of drives in the field, the Mode Sense values given in the following tables may not exactly match those of some drives. The following tables list the values of the data bytes returned by the drive in response to the
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 64
    and changeable values for 300GB drives MODE DATA HEADER: 00 00 05 12 8B 01 30 02 MODE PAGES: DEF 81 0A C0 14 FF 00 00 00 05 00 FF FF CHG FF FF DEF 80 06 00 80 0F 00 00 00 CHG 80 06 B7 C0 8F 00 00 00 56 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 65
    Table 10: Mode Sense data default and changeable values for 146GB drives MODE DATA HEADER: 00 00 05 12 8B 01 30 02 MODE PAGES: DEF 81 0A C0 14 FF 00 00 00 05 00 FF FF CHG FF FF FF DEF 80 06 00 80 0F 00 00 00 CHG 80 06 B7 C0 8F 00 00 00 Savvio 15K.3 SAS Product Manual, Rev. D 57
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 66
    support column indicates the feature or condition is supported. An "N" in the support column indicates the feature or condition is not supported. Table 11: Miscellaneous features Supported 128 queue tags supported) Deferred error Table 12: Miscellaneous status Supported Y Status Good Y Check
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 67
    15 provide the dimensions of the SAS connector. Details of the physical, electrical, and logical characteristics are provided within this section. The operational aspects of Seagate's SAS drives are provided in the SAS Interface Manual. Figure 13. Physical interface Savvio 15K.3 SAS Product
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 68
    ) 5.08 B 0.84 0.05 (22X) 0.15 B 4.90 0.08 P15 P1 S1 S7 CL OF DATUM B Figure 14. SAS device plug dimensions 60 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 69
    A 0.03 1.23 0.05 65 30 0.08 0.05 Detail 2 1.90 0.08 2.40 0.08 0.10 A D Figure 15. SAS device plug dimensions (detail) SECTION B - B Savvio 15K.3 SAS Product Manual, Rev. D 61
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 70
    connector is illustrated in Figures 14 and 15. 12.4.4 Electrical description SAS drives use the device connector for: • DC power • SAS interface • Activity Volts P15* 12 Volts * - Short pin to support hot plugging NC - No connection in the drive. 62 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 71
    and signal name information. 12.5.1 Ready LED Out The Ready LED Out signal is driven by the drive as indicated in Table 14. Table 14: Ready LED Out conditions Normal command activity Ready LED Meaning bit on and off for 0.5 seconds) Toggles on/off Savvio 15K.3 SAS Product Manual, Rev. D 63
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 72
    , and Applications layers of the SAS interface, refer to the Seagate SAS Interface Manual, part number 100293071. For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual, part number 100293068. 64 Savvio 15K.3 SAS Product
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 73
    49 commands supported 50 condensation 31 condition met/good status 58 connector illustrated 62 requirements 62 continuous vibration 34 cooling 47 CRC error 16 Cryptographic erase 39 cryptographic erase 40 Current profiles 27 customer service 21 D DAR 43 Data Bands 39 data bands 38 data block size
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 74
    47 heat source 47 host equipment 48 hot plugging the drive 16 humidity 31 humidity limits 31 I Identifying a PI drive 45 Idle Read After Write 44 Idle1 22 Idle2 22 Idle3 22 inquiry data 54 installation 46 guide 6 interface commands supported 50 error rate 15 errors 16 illustrated 59 physical 59
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 75
    58 Zero latency read 58 miscellaneous status support ACA active 58 ACA active, faulted distribution 3 power management 22 PowerChoice 22 PowerChoice data heads 11 ReadLockEnabled 39 receivers 63 recommended mounting 33 Recoverable Errors 15 recovered media data 15 Savvio 15K.3 SAS Product Manual
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 76
    self-encrypting drives 38 Self-Monitoring Analysis and Reporting Technology 9, 17 Serial Attached SCSI (SAS) Interface Manual 2 shielding management response codes 49 Function complete 00 49 Function not supported 05 49 Function reject 04 49 task set full status 58 TCG 38 technical support services
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 77
    W warranty 21 WriteLockEnabled 39 Z zero latency read 58 zone bit recording (ZBR) 8 Savvio 15K.3 SAS Product Manual, Rev. D 69
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 78
    70 Savvio 15K.3 SAS Product Manual, Rev. D
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 79
  • Seagate Savvio 15K | Savvio 15K.3 SAS Product Manual - Page 80
    Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Product Manual
Savvio
®
15K.3 SAS
100629381
Rev. D
January 2012
Standard Models
ST9300653SS
ST9146853SS
Self-Encrypting Drive Models
ST9300553SS
ST9146753SS
SED FIPS140-2 Models
ST9300453SS
ST9146653SS