Sealey 1020LEO Instruction Manual

2TONNE LOW ENTRY SHORT CHASSIS

TROLLEY JACK

MODEL NO:

1020LE.V3 SERIES

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

1. SAFETY

IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS

Please remember a trolley jack is a lifting device and is not designed to support a load. Never get

underneath a vehicle supported only by a jack - your life is at risk. We stock a comprehensive

range of axle stands.

Please see relative section of catalogue or website for full details.

9

Ensure the jack is in sound condition and good working order. Take action for immediate repair

or replacement of damaged parts. Use genuine parts only. The use of unapproved parts may be

dangerous and will invalidate the warranty.

9

Locate the jack in a suitable, well lit working area.

9

Keep working area clean and tidy and free from unrelated materials.

9

Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.

9

Place wedges under wheels of vehicle.

9

Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear

(or “PARK” if automatic).

9

Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc.,

to allow for vehicle tilting.

9

Ensure there are no passengers in the vehicle.

9

Ensure all non-essential persons keep a safe distance whilst the jack is in use.

9

Only place jack under those lifting points recommended by vehicle manufacturer

(see vehicle hand book).

9

Check the lifting point is stable and centred on the jack saddle.

9

Ensure the jack wheels are free to move and that there are no obstructions.

9

When lifting a load at the jack’s maximum rating (2tonne) or close to it, it is recommended that

the effort of raising the load be reduced by the assistance of a second person during this operation.

▲

DANGER:

Use the jack for lifting only,

NOT

for supporting the lifted load.

9

Use suitable capacity axle stands under the vehicle before proceeding with any task.

9

Ensure there are no persons or obstructions beneath the vehicle before lowering.

9

Use a qualified person to maintain or repair the jack hydraulic system.

8

DO NOT

operate the jack if damaged.

8

DO NOT

allow untrained persons to operate the jack.

8

DO NOT

exceed the rated capacity of the jack.

8

DO NOT

allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.

8

DO NOT

jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.

8

DO NOT

work under the vehicle until axle stands have been correctly positioned.

8

DO NOT

use the jack for purposes other than those for which it is intended.

8

DO NOT

top up hydraulic system with brake fluid. Use hydraulic jack oil only. (Sealey Part No:

8

HJO500MLS or HJO5LS)

8

DO NOT

adjust the safety overload valve.

9

When not in use store jack, fully lowered, in a safe, dry, childproof area.

2. INTRODUCTION

Heavy-duty chassis with strengthening flanges along the top edge for extra torsional rigidity under

load. Profiled lifting arm allows low clearance height of just 85mm making this unit suitable for

sports and custom cars. Fitted with heavy-duty one-piece hydraulic unit with pump-through action

preventing handle locking at maximum ram extension. White saddle aids positioning under vehicle

and safety valve prevents overloading.

1020LE.V3 SERIES

Issue 2 (2,3)

30/04/21

Original Language Version

© Jack Sealey Limited

Refer to

instructions

Wear safety

footwear

1

35

24R

TJL3

Chock

wheels

Never

exceed

jack capacity

Close

Raise

Lower

Lift & twist

to lower

OR

Use on a hard level floor

Apply

handbrake

www.sealey.co.uk

Use suitable axle stands

X2

Raise

Sealey 1020LEO Instruction Manual

Sealey 1020LEO Manual

Sealey 1020LEO manual content summary: