Sennheiser TeamConnect Ceiling 2 ES1 Ceiling Audio Solution TeamConnect Ceilin
Sennheiser TeamConnect Ceiling 2 Manual
View all Sennheiser TeamConnect Ceiling 2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sennheiser TeamConnect Ceiling 2 manual content summary:
- Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 1
April 2020 Application Guide ES1 Ceiling Audio Solution Microsoft Teams Certified Medium Room System - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 2
Page Intentionally Left Blank - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 3
Sennheiser TeamConnect Ceiling 2 (TCC2) Additional components required, but not included: Microsoft Teams Room camera and display Network switch with PoE for Dante ES1 System Wiring Diagram Microphone and Loudspeaker Placement EdgeMax guide for proper installation instructions. April 2020 Page 1 - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 4
Application Guide ES-1 Audio System Set-up Guide for Microsoft Teams Figure 2: Side view of EdgeMax EM180 75-degree vertical dispersion and placement Figure 3: Top view of EdgeMax EM180 180-degree horizontal dispersion April 2020 Page 2 - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 5
ES-1 Audio System Set-up Guide for Microsoft Teams 10ft ceiling Figure 4: Plan view showing the relative proprietary near-zero-latency link between Bose processors and amplifiers and can carry up to eight channels of digital audio on a single shielded Category 5 (STP) cable. Connect the DSP and - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 6
Ceiling 2 (TCC2) microphone array are both Dante products. Connecting the Sennheiser TCC2 microphone array requires two Cat 5 ethernet cables. The Dante Primary port and the Ethernet port on the TCC2 connect to the network switch. Note: Refer to the TeamConnect Ceiling 2 Instruction manual - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 7
Application Guide ES-1 Audio System Set-up Guide for Microsoft Teams DSP Configuration A reference file configuration file is available for download with preconfigured settings. This reference file is available for download from PRO. - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 8
will illuminate at the previously configured brightness setting. Microphone Orientation Orientation is determined from a top-down view. Positions are based on the direction in which the Sennheiser logo is pointing. The default position of the Sennheiser logo is 0 degrees. Figure 9: Control panel for - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 9
Sennheiser TCC2 elements in ControlSpace Designer Dante Receive (1) is the input from the TCC2 output, and Dante Transmit (2) is a return channel to the TCC2 to enable the beam freeze operation. When the Dante IP host via a micro-USB connection. Setup and deployment of specific Microsoft Teams Rooms - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 10
(as shown in Figure 13), and use the dropdown menus to select the EX-440C for each of the three parameters: Microphone for Conferencing, Speaker for Conferencing, and Default Speaker. When you are finished, click Save and exit to return to the user interface. Figure 13: View of MTR settings - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 11
Guide for Out block correspond to microphone mute; and S associates with call status. HID mute and volume synchronize both USB channels. To enable control of table summarizes the port function and default state for each HID operation: Function Logic Port State Default TCC2 LED Color/State Call not - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 12
. TeamConnect Ceiling 2 Setup and Configuration The Sennheiser TCC2 is a ceiling-mounted dynamic beamforming microphone. It supports both Dante (input/output) and auxiliary-balanced analog (output) connections for audio transport. A PoE/Control connection and the Sennheiser Control Cockpit software - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 13
System Set-up Guide for Microsoft Teams Figure 17: Properties window Figure 18: Control Cockpit interface Levelling the TCC2 Beam Freeze The far-end signal (the signal received from the far-end presenter) can be routed from the DSP to the TCC2 AEC Ref input via Dante. This AEC reference signal - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 14
software for the AEC, set the output level for the AEC ref signal to the minimum level. This allows the position of the near-end presenter to be tracked properly, never reaching the Static status. The Static status is indicated in Sennheiser between the AEC reference and Dante Tx, provided for this - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 15
Guide for Microsoft Teams Troubleshooting and Commissioning Guide The TCC2 does not connect. From the front panel OLED display, confirm that the EX-440C is the in same IP range as the TCC2 by using Sennheiser Control Cockpit. Confirm that the correct IP is too low. The default MTR level for every - Sennheiser TeamConnect Ceiling 2 | ES1 Ceiling Audio Solution TeamConnect Ceilin - Page 16
the US, a bracket kit is required to adapt the microphone to a 24 x 24-inch grid. Additionally, the microphone can be surface-mounted in hard ceilings, or pole-mounted or wire-mounted in open ceilings. Refer to the TeamConnect Ceiling 2 instruction manual for proper mounting instructions. ©2020 Bose
April 2020
Application Guide
ES1 Ceiling Audio Solution
Microsoft Teams Certified
Medium Room System