Sharp HTSB200 HT-SB200 Operation Manual - Page 16

General control - 2 1 sound bar

Get Sharp HTSB200 - Sound Bar Speaker PDF manuals and user guides
UPC - 074000369399
View all Sharp HTSB200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Preparation for Use HT-SB200 Remote control (continued) Caution: ● Do not use rechargeable battery (nickel-cadmium battery, etc.). ● Danger of explosion if battery is incorrectly replaced. ● Replace only with the same or equivalent type. ● Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. ● Installing the battery incorrectly may cause the speaker to malfunction. Notes concerning use: ● Replace the battery if the operating distance is reduced or if the operation becomes erratic. Purchase "CR 2025", coin lithium battery. ● Periodically clean the transmitter on the remote control and the sensor on the speaker with a soft cloth. ● Exposing the sensor on the speaker to strong light may interfere with operation. Change the lighting or the direction of the speaker if this occurs. ● Keep the remote control away from moisture, heat, shock, and vibrations. ■ Test of the remote control Point the remote control directly at the remote sensor on the speaker. The remote control can be used within the range shown below: Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy your system. Remote sensor STANDARD SPORT CINEMA / GAME NEWS ON/STAND-BY VOL. SURROUND FUNCTION SOUND BAR SYSTEM HT-SB200 15˚ 15˚ 8" - 20' (0.2 m - 6 m) 16 General control STANDARD SPORT CINEMA / GAME NEWS ON/STAND-BY VOL. SURROUND FUNCTION SOUND BAR SYSTEM HT-SB200 ■ To turn the power on Press the ON/STAND-BY button. ● The power indicator turns green. If the power does not turn on, check whether the power cord is plugged in properly. To set the speaker to stand-by mode: ● Press the ON/STAND-BY button again. The STAND-BY indicator turns red. ■ Display brightness control Press the DIMMER button to adjust the brightness of the display and sound mode indicator. Sound mode indicator and display bright Sound mode indicator and display dim Sound mode indicator and display off. Pressing any button will light up the display for 3 seconds only. ■ Volume auto fade-in If you turn off and on the speaker with the volume set to 40 or higher, the volume starts at 20 and fades in to the last set level. ■ Volume control Speaker operation: Press volume up (VOL. +) to increase the volume and press volume down (VOL. -) to decrease the volume. 00 01 02 ..... 59 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
16
HT-SB200
Preparation for Use
Remote control (continued)
Caution:
●
Do not use rechargeable battery (nickel-cadmium battery, etc.).
●
Danger of explosion if battery is incorrectly replaced.
●
Replace only with the same or equivalent type.
●
Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
●
Installing the battery incorrectly may cause the speaker to
malfunction.
Notes concerning use:
●
Replace the battery if the operating distance is reduced or if
the operation becomes erratic. Purchase “CR 2025”, coin
lithium battery.
●
Periodically clean the transmitter on the remote control and
the sensor on the speaker with a soft cloth.
●
Exposing the sensor on the speaker to strong light may
interfere with operation. Change the lighting or the direction
of the speaker if this occurs.
●
Keep the remote control away from moisture, heat, shock,
and vibrations.
■
Test of the remote control
Point the remote control directly at the remote sensor on the
speaker
.
The remote control can be used within the range shown
below:
Press the ON/STAND-BY button. Does the power turn on? Now,
you can enjoy your system.
General control
■
To turn the power on
Press the ON/STAND-BY button.
●
The power indicator turns green. If the power does not turn
on, check whether the power cord is plugged in properly.
To set the speaker to stand-by mode:
●
Press the ON/STAND-BY button again.
The STAND-BY indicator turns red.
■
Display brightness control
Press the DIMMER button to adjust the brightness of the display
and sound mode indicator.
■
Volume auto fade-in
If you turn off and on the speaker with the volume set to 40 or
higher, the volume starts at 20 and fades in to the last set level.
■
Volume control
15˚
15˚
Remote sensor
8” - 20’
(0.2 m - 6 m)
Speaker operation:
Press volume up (VOL. +) to increase
the volume and press volume down
(VOL. –) to decrease the volume.
S
TANDARD
S
PORT
VOL.
S
URROUND
FUNCTION
CINEMA / GAME
NEW
S
ON/
S
TAND-BY
S
o
un
d mode i
n
dicator a
n
d di
s
play bri
g
ht
S
o
un
d mode i
n
dicator a
n
d di
s
play dim
S
o
un
d mode i
n
dicator a
n
d di
s
play off. Pre
ss
i
ng
a
n
y b
u
tto
n
will li
g
ht
u
p the di
s
play for
3
s
eco
n
d
s
o
n
ly.
00
01
02
.....
59
60