Sharp LC-40LE830U LC-40LE830U LC-46LE830U LC-52LE830U LC-60LE830U Opera - Page 59

Using a PC Example System Options Menu System Options View Option AQUOS LINK Setup Input Terminal Setting Menu Design O ti L k O t 1 Press MENU to display the MENU screen, and then press c/d to select "System Options". 2 Press a/b to select "Input Terminal Setting", and then press ENTER. 3 Press a/b to select "PC input" or "Audio Select", and then press ENTER. 4 Press a/b to select a specific adjustment item, and then press ENTER to set each item. 5 Press a/b (or c/d) to select or adjust the desired setting, and then press ENTER. Adjusting the PC Image Auto Sync. (for Analog PC Input Mode Only) For automatically adjusting the PC image. Yes: Auto Sync. starts and "Now adjusting the image." displays. No: This function does not work. • When "Auto Sync." is successful, "Completed" displays. If not, "Auto Sync." failed. • "Auto Sync." may fail even if "Completed" displays. • "Auto Sync." may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing "Auto Sync.". • Be sure to connect the PC to the TV and switch it on before starting "Auto Sync.". Fine Sync. Ordinarily you can easily adjust the picture as necessary to change image position using "Auto Sync.". In some cases, however, manual adjustment is needed to optimize the image. H-Pos.: Centers the image by moving it to the left or right. V-Pos.: Centers the image by moving it up or down. Clock: Adjust when the image flickers with vertical stripes. Phase: Adjust when characters have low contrast or when the image flickers. • For resetting all "Fine Sync." adjustment items to the factory preset values, press a/b to select "Reset", and then press ENTER. • It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected. • The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical. • The screen position variable ranges depend on the View Mode or the signal type. The ranges can be seen on the position-setting screen. Setting Audio Input Audio Select This function sets the terminal to output the computer audio. The adjustment items vary depending on the input source. Select the input source corresponding to the terminal connected to the PC and then adjust the desired item. ■ PC IN Video: Select this when the TV and PC are connected using an analog RGB cable and the audio is not input. Video+Audio: Select this when the TV and PC are connected using an analog RGB cable and the audio is input via a Ø 3.5 mm stereo minijack. ■ HDMI 1 HDMI(Digital): Select this when the TV and PC are connected using an HDMI-certified cable and audio is input via the same cable. HDMI+Analog: Select this when the TV and PC are connected using a DVI-HDMI conversion cable and the audio is input via a Ø 3.5 mm stereo minijack. • When "Audio Select" is set to "HDMI(Digital)", sound will not be produced if you use only an HDMI-certified cable to connect HDMI-compatible equipment. To produce sound, you should make an analog audio connection. • If you want to connect HDMI-compatible equipment using only an HDMI-certified cable, set "Audio Select" to "HDMI(Digital)". PC Compatibility Chart It is necessary to set the PC correctly to display XGA and WXGA signal. Resolution Horizontal Vertical VESA Frequency Frequency Standard 720 x 400 31.5 kHz 70 Hz VGA 31.5 kHz 60 Hz 640 x 480 37.9 kHz 72 Hz O O 37.5 kHz 75 Hz O 35.1 kHz 56 Hz O SVGA 800 x 600 37.9 kHz 48.1 kHz 60 Hz 72 Hz O O 46.9 kHz 75 Hz O 48.4 kHz 60 Hz O XGA 1024 x 768 56.5 kHz 70 Hz O 60.0 kHz 75 Hz O WXGA 1360 x 768 47.7 kHz 60 Hz O SXGA 1280 x 1024 64.0 kHz 60 Hz O SXGA+ 1400 x 1050 65.3 kHz 60 Hz O UXGA 1600 x 1200 75.0 kHz 60 Hz O 1080p 1920 x 1080 67.5 kHz 60 Hz VGA and XGA are registered trademarks of International Business Machines Corp. 57