Sharp MX 4501N Installation Manual
Sharp MX 4501N - Color Laser - All-in-One Manual
 |
View all Sharp MX 4501N manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp MX 4501N manual content summary:
- Sharp MX 4501N | Installation Manual - Page 1
Fax expansion kit 15-1 Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. SHARP CORPORATION This document has been published to be used for after sales service - Sharp MX 4501N | Installation Manual - Page 2
AR-SC2) Service Manual PCL5c/PCL6 Network PCL5c/PCL6 Network driver scanner driver scanner (Sharpdesk 1 license) (Sharpdesk 1 license) RSPF DSPF *&& Copier/Printer /Scanner model (MX-3500N) (MX-4500N) HDD Copier/Printer /Scanner model (MX-3501N) (MX-4501N) 4. Exit tray unit (MX-TRX2 - Sharp MX 4501N | Installation Manual - Page 3
GDI printer PCL printer PS printer EFI printer Main body LCD FAX Scanner Filing HDD RSPF DSPF Automatic duplex Security Internet Fax STD: Standard provision, OP: Option OP*1: Product key target. OP*2: No support for some areas. C. Combination of options list MX-3500N/MX-4500N MX-3501N/MX-4501N - Sharp MX 4501N | Installation Manual - Page 4
MX-3501N/4501N Service Manual 1. Installing (use) conditions Before installing the machine, check that the following installing (use) conditions are satisfied. If the installing (use) conditions are not satisfied, the machine may not display full performances, resulting in troubles not, color shift - Sharp MX 4501N | Installation Manual - Page 5
a machine which produces vibrations. If vibrations are applied to the copier machine, copy images may be deflected and a trouble may be caused. B. Fixing tape and protection pads removal 2. of four persons is required.) Transit must be made in packed condition. MX-3500N/4500N, MX-3501N/4501N 1 - 2 - Sharp MX 4501N | Installation Manual - Page 6
1 2 3 C. Removal of parts packed together No. Parts name 1 Waste toner bottle unit 2 Operation manual 3 Operation manual pocket Quantity 1 1 1 4. Installation * When to the position shown in the figure for storage. MX-3500N/4500N, MX-3501N/4501N 1 - 3 - Sharp MX 4501N | Installation Manual - Page 7
(2) Scanner (2/3 mirror unit) lock release 1) Remove the optical unit fixing release lever to apply more pressure. 3) Open the DV lock lever, and release the fixing screw. (1 position for each color) 1 2 NOTE: If the machine is left unused for one month or more, the heat roller rubber may be - Sharp MX 4501N | Installation Manual - Page 8
belt protect sheet horizontally in the arrow direction. 3) Apply titanium hydroxide to the belt within approx. 15 cm from the driving roller. Driving roller 15cm MX-3500N/4500N, MX-3501N/4501N 1 - 5 - Sharp MX 4501N | Installation Manual - Page 9
fly apart. Cleaner UN 8) Mount the primary transfer UN on the machine and execute simulation 25-1 (3-minute belt idling) once. 9) Check omissions in characters, and if many omissions are found, execute simulation 25-1 once again. 10) If titanium hydroxide flies apart near the resist roller, clean - Sharp MX 4501N | Installation Manual - Page 10
E. Developing (each color) installation 1) Remove two fixing screws of the DV cover. 4) Install the DV cover in the arrow direction (A). with {). 6) Shake the developer unit horizontally a few times. * When supplying developer, do not tilt the developing unit. MX-3500N/4500N, MX-3501N/4501N 1 - 7 - Sharp MX 4501N | Installation Manual - Page 11
. 3) Turn ON the power switch on the operation panel. ON ON 10) Install the waste toner bottle unit (package part No. 1). 4) With the front cabinet open, enter the data for Simulation 25-2. TEST SIMULATION NO.25-02 AUTOMATIC DEVELOPER ADJUSTMENT AT DEVE ADJ_L_K : 128 AT DEVE VO_L_K : 128 - Sharp MX 4501N | Installation Manual - Page 12
1/2 Note: Be sure to select all of the four colors: K, C, M, Y. 7) Exit from Simulation mode by pressing the [CA] key on the main unit. 3) Open the front cover, and insert each toner cartridge. * Be sure to install the color cartridges to their proper positions. Avoid installation to a different - Sharp MX 4501N | Installation Manual - Page 13
waste toner bottle unit. 1 2 6) Close the front cabinet. 3) Detach the LSU cleaning bar from the front cover. I. Installation of the operation manual pocket 1) Install the Operation Manual Manual pocket. Then, lift the pawl on the upper side and insert it, and slide down to install. * If the MX- - Sharp MX 4501N | Installation Manual - Page 14
SETTINGS 2) Touch the [Paper Tray Settings] key. System Settings Admin Password Exit Total Count Paper Tray Settings Printer Condition Settings Default Settings Address Control Document Filing Control List Print (User) Fax Data Receive/Forward USB-Device Check 3) Touch the [Tray Settings - Sharp MX 4501N | Installation Manual - Page 15
2) paper printed on the document table. Place the printed color patch image (adjustment pattern) paper so that the thin lines on the paper are on the left side. At this time, place 5 sheets of white paper on the printed color patch image (adjustment pattern) paper. MX-3500N/4500N, MX-3501N/4501N - Sharp MX 4501N | Installation Manual - Page 16
. TEST SIMULATION NO.67-24 PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE 0 CLOSE PLEASE SELECT THE MODE (FACTORY) OR (SERVICE) AND PLACE THE PRINTED TEST PATCH ON DOCUMENT GLASS THEN PRESS [EXECUTE]. , 㪁LIGHT AREA AT LEFT SIDE ON DOCUMENT GLASS. FACTORY SERVICE EXECUTE The copy color balance - Sharp MX 4501N | Installation Manual - Page 17
mode is supported: Execute SIM 64-5 to print the print test pattern. Set each set value to the default and press [EXECUTE] key. The print test pattern is printed. The print density must be changed Paper • Toner cartridge • Development cartridge 3) Lock the following sections. • Scanner (Optical - Sharp MX 4501N | Installation Manual - Page 18
front cabinet of the main unit. OFF 3) Disconnect the power plug of the main unit from the power outlet, and remove the earth cord. MX3500N MX-DEX3/DEX4 2 - 1 - Sharp MX 4501N | Installation Manual - Page 19
of the both sides of the main unit. 3) Remove the No. 2 paper feed tray. 2 2 1 1 4) Pull out the No. 3 paper feed tray until it stops. 2 1 MX3500N MX-DEX3/DEX4 2 - 2 - Sharp MX 4501N | Installation Manual - Page 20
connection plates, and fix them with the fixing screws. 6) Replace the No. 3 and No. 2 trays to the original positions. 8) Install the connection plate covers. 2 1 1 2 2 1 MX3500N MX-DEX3/DEX4 2 - 3 - Sharp MX 4501N | Installation Manual - Page 21
the power, check to insure that the fixing material of the tray is disengaged. If the power is turned on without disengaging the fixing material, a trouble may be resulted. 4) Close the cassette which was pulled out. 4) Install the connector cover and fix it with a screw. MX3500N - Sharp MX 4501N | Installation Manual - Page 22
press the [OK] key). Changing the adjustment value by 1 shifts the position by approximately 0.1 mm. Repeat steps 4) to 6) until the condition shown in step 6) is satisfied. 8) After you have completed the adjustment, exit from Simulation mode by pressing the [CA] key. MX3500N MX-DEX3/DEX4 2 - 5 - Sharp MX 4501N | Installation Manual - Page 23
on the operation panel. B. Installation of the exit roller unit 1) Open the right door. 2 1 2) Remove the screw, and remove the connector cover. OFF OFF MX3500N MX-TRX2 3 - 1 - Sharp MX 4501N | Installation Manual - Page 24
(B) (package part No. 2). * Be careful of the installing direction of the full detection actuator. D. Tray setting Use SIM26-1 to set the tray YES/NO. B B A MX3500N MX-TRX2 3 - 2 - Sharp MX 4501N | Installation Manual - Page 25
the fixing screw of the tray is removed. If the power is turned on without removing the fixing screw, a trouble may be resulted. C. Check the packed items 1) Check that all the items are included in the package. B. 1) Turn OFF the power switch on the operation panel. OFF OFF MX3500N MX-LCX1 4 - 1 - Sharp MX 4501N | Installation Manual - Page 26
on the lower side. 5) Remove the cover. 6) Temporarily fix the fixing screw B (package part No. 4) midway. 2) Remove the right door cover from the machine. 1 3 2 3 MX3500N MX-LCX1 4 - 2 - Sharp MX 4501N | Installation Manual - Page 27
on the front side for the adjustment. Do not touch the screw on the rear side. NOTE: If the screw is loosened or removed when servicing, be sure to execute "C. Height adjustment of the large capacity tray unit" after completion of - Sharp MX 4501N | Installation Manual - Page 28
that the stopper does not function. D. Connector connection 1) Remove the screw, and remove the connector cover. 3) Pull out the tray again until it stops. MX3500N MX-LCX1 4 - 4 - Sharp MX 4501N | Installation Manual - Page 29
guide. 3) Set the mark position ( ) of the auxiliary guide guide and the cassette R to the same guide adjustment plate confirmed in procedure 1). (If the scale of the size guide adjustment plate is at the center, set it to the center. If the size guide cabinet. b. Auxiliary guide size switch 1) When - Sharp MX 4501N | Installation Manual - Page 30
F/R according to the desired size. Also adjust the upper section according to the desired size, and fix with the four fixing screws (blue screws). MX3500N MX-LCX1 4 - 6 - Sharp MX 4501N | Installation Manual - Page 31
stopper to the original position, and fix the fixing screw. b. Auxiliary guide size switch * Since the auxiliary guide setting is not required, fix the auxiliary guide to either of A4 or LT. (To prevent against missing of to B5, the rear edge shaft cannot be switched to B5. MX3500N MX-LCX1 4 - 7 - Sharp MX 4501N | Installation Manual - Page 32
value and press the [OK] key). Changing the adjustment value by 1 shifts the position by approximately 0.1 mm. Repeat steps 4) to 6) until the condition shown in step 6) is satisfied. 8) After you have completed the adjustment, exit from simulation mode by pressing the [CA] key. (2) Mechanical - Sharp MX 4501N | Installation Manual - Page 33
To adjust the print line in the direction B from the paper center as shown in the figure: 1) Loosen two fixing screws (red screws) of the front/rear size guide adjustment plate, and move the size guide adjustment plate in shift. Repeat the procedures until there is no shift. MX3500N MX-LCX1 4 - 9 - Sharp MX 4501N | Installation Manual - Page 34
lift it as shown in the table below. 4 5 6 8 9 10 11 12 No. Packed part names 1 Finisher fixing plate 2 Front slide rail 3 Finisher slide stopper 8 Fixing screw 9 Resin clip 10 Coin screw 11 Staple position label (For scanner) 12 Staple position label (For RSPF/DSPF) 7 Quantity 1 1 - Sharp MX 4501N | Installation Manual - Page 35
earth cord and disconnect the power plug of the main unit from the power outlet. 2) Remove two screws, and remove the front cabinet upper. MX3500N MX-FNX1 5 - 2 - Sharp MX 4501N | Installation Manual - Page 36
unit frame with the hole in the finisher fixing plate (package part No. 1). 7) Fix the right cover plate with the fixing screw (package part No. 8). 11) Fix the rear slide rail with the fixing screw (package part No. 8). * Fix the side plate of the paper exit shifter with the fixing - Sharp MX 4501N | Installation Manual - Page 37
Install the front cabinet upper with two screws. E. Staple position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (package part No. 11) Corner R end fitting Label attachment reference * Corner of the "upper cabinet rear" Corner R end fitting MX3500N - Sharp MX 4501N | Installation Manual - Page 38
When streaks appear on copy or scan images, open the automatic document feed unit and clean the document scan section with the glass cleaner (accessory). Document scan section RSPF 3) Turn ON the power switch on the operation switch in the front cabinet of the main unit. ON MX3500N MX-FNX1 5 - 5 - Sharp MX 4501N | Installation Manual - Page 39
package. 1 2 No. Packed part names 1 Punch position label (For scanner) 2 Punch position label (For RSPF/DSPF) Quantity 1 1 2. Installation * When the punch unit is installed together with installation of the MX-FNX1 (inner finisher), first install the inner finisher, and then install - Sharp MX 4501N | Installation Manual - Page 40
slide the inner finisher. 2 1 5) Remove two screws, and remove the front cabinet upper. 6) Remove the screw, and remove the band and the punch cover. MX3500N MX-PNX1A/B/C/D 6 - 2 - Sharp MX 4501N | Installation Manual - Page 41
7) Remove the screw, and remove the dummy punch unit. 11) Remove the dust box. 8) Fix the punch unit with a screw. * When installing the punch unit, be careful not to the finisher slide stopper between the slide rail and the accuride, and fix it with the coin screw. MX3500N MX-PNX1A/B/C/D 6 - 3 - Sharp MX 4501N | Installation Manual - Page 42
1) Attach the label to the position indicated in the figure. [For scanner] (package part No. 1) Corner R end fitting No clearance First scan images, open the automatic document feed unit and clean the document scan section with the glass cleaner (accessory). Document scan section RSPF 2) Open - Sharp MX 4501N | Installation Manual - Page 43
left cabinet 3 Reverse tray 4 Fixing screw A 5 Fixing screw B 6 Ornamental screw 7 Reverse detection actuator 8 Stopper Quantity 1 1 1 6 1 1 1 1 2. Installing the MX-RBX1 * Before starting installation, check to insure that the data lamp on the operation panel does - Sharp MX 4501N | Installation Manual - Page 44
fix it with the fixing screw A (package part No. 4). * Be sure to clamp and fix the paper exit tray shifter side plate with the fixing guide. MX3500N MX-RBX1, MX-FNX2 7 - 2 - Sharp MX 4501N | Installation Manual - Page 45
part No. 2) into the slit on the lower surface of the scanner left cabinet. Install the interface left cabinet with the fixing screw A 8) with the fixing screw B (package part No. 5). 11) Insert the interface pass unit along the guide rail. 8) Fix the reverse tray with the ornamental screw - Sharp MX 4501N | Installation Manual - Page 46
3 Staple unit 4 Staple cartridge 5 Fixing screw A 6 Fixing screw B 7 Paper entry guide 8 Staple position label (For scanner) 9 Staple position label (For RSPF/DSPF) 10 Punch position label (For scanner) 11 Punch position label (For RSPF/DSPF) Quantity 1 1 1 1 2 8 1 1 1 1 1 * The punch - Sharp MX 4501N | Installation Manual - Page 47
from the machine) to the saddle finisher. First, insert the pawl on the lower side of the Operation Manual pocket. Then, lift the pawl on the upper side and insert it, and slide down to install. cover of the finisher, and insert the staple unit (package part No. 3). MX3500N MX-RBX1, MX-FNX2 7 - 5 - Sharp MX 4501N | Installation Manual - Page 48
on the front side. If the guide pin is inserted smoothly, tighten dowel Pawl 1 (2) When the guide pin is fit with the connection guide pin is smoothly inserted into the connection hole. Connection hole Guide guide pin is not inserted smoothly, perform the following adjustment. (1) When the guide - Sharp MX 4501N | Installation Manual - Page 49
position label attachment 1) Attach the label to the position indicated in the figure. [For scanner] (package part No. 8) 4) When the clearances are even, tighten the fixing screw . 9) DSPF CAUTION Cleaning of the document scan section When streaks appear on copy or scan images, open the automatic - Sharp MX 4501N | Installation Manual - Page 50
outlet. I. Storage of the paper entry guide 1) When the punch unit is not installed, store the paper entry guide (package part No. 7) to the position the table below. Pinch the paper guide with the plate (A), and then insert the boss (B) in the hole in the paper guide. B B2 2) Open the front - Sharp MX 4501N | Installation Manual - Page 51
(M4 x 6 with tooth lock washer) 4 Dust box label 5 Punch position label (For scanner) * 6 Punch position label (For RSPF) * Quantity 1 1 1 1 1 1 * position labels (No.5 and No.6) and must be those bundled with the MX-FNX2 rather than those bundled with the AR-PN1A/B/C/D. 2. Installation - Sharp MX 4501N | Installation Manual - Page 52
the screws, and remove the front cabinet upper. C. Replacement of the paper entry paper guide 1) Remove the dust box of the punch unit. 4) Remove the screw, and remove cabinet upper. B A 2) Remove the guide from the dust box. The guide is not used in the MX-FNX2. C MX3500N AR-PN1A/B/C/D 8 - 2 - Sharp MX 4501N | Installation Manual - Page 53
which are fixing the paper entry paper guide. 7) Install the paper entry paper guide exclusively used for the MX-FNX2 packed with the saddle finisher. 1 4) Remove the hook (boss) on the upper side of the paper entry paper guide. 2 8) Fix the incoming paper guide using the screws removed in step - Sharp MX 4501N | Installation Manual - Page 54
11) Connect the punch unit harness to the finisher PWB. Remove the clamp which is fixing the harness. Wire the harness A (Purple) (package part No. 1) and - Sharp MX 4501N | Installation Manual - Page 55
Attach the label to the position indicated in the figure. [For scanner] (package part No. 5) Corner R end fitting No clearance First scan images, open the automatic document feed unit and clean the document scan section with the glass cleaner (accessory). Document scan section 2) Connect the earth - Sharp MX 4501N | Installation Manual - Page 56
of the dust full sensor. After completion of the adjustment, the LED2 lights up. LED2 ON PSW1 F. Dust full sensor adjustment * When the dust box guide is removed, the dust full sensor may sense dust full earlier than the normal detection level. To prevent against this, this adjustment must be - Sharp MX 4501N | Installation Manual - Page 57
(including HDD) of the main unit. When the data security kit is installed, all the job data stored in the memory (including HDD) of the main unit will be lost. • If the LINE indicator or the DATA indicator for the printer and image transmission on the operation panel is lit or blinking - Sharp MX 4501N | Installation Manual - Page 58
and 2) additionally. 1) Remove the screw that secures the fax box unit. 2) Remove the fax box unit. F. Attach the DOCC PWB. 1) Connect the that have been loosened. • If the fax box unit is installed, carry out steps 4) and 5) additionally. 4) Hang the fax box unit that has been removed in step - Sharp MX 4501N | Installation Manual - Page 59
starts. K. Make user settings of the data security function. Operation of the data security function can be set with System Settings (Administrator). For details, see the MX-FRX1U operation manual, and check the operation. If some files have been stored using the document filing function (including - Sharp MX 4501N | Installation Manual - Page 60
print is made at procedure d), check the connection of the DOCC PWB. f) After check at the installing, touch the [SYSTEM SETTINGS], and touch the [DOCUMENT CONTROL SETTING], then set the copy mode to always unprint. (When case of maintenance, set to the original user setting.) MX3500N MX-FRX2, MX - Sharp MX 4501N | Installation Manual - Page 61
Unpacking A. Parts included Service Manual 1 2 No. Packed part names 1 CD-ROM (For Screen Font) 2 Product key sheet Quantity 1 1 NOTE: To set up the PS driver, do not use the CD-ROM which is included in the MX-PKX1 but use the CD-ROM which is included in the MX-PBX1. 2. Installation - Sharp MX 4501N | Installation Manual - Page 62
Manual Quantity 1 1 2. Installation A. Installation of the barcode font ROM PWB 1) Turn OFF the main switch of the copier, and disconnect the power plug of the copier from the power outlet. 2) Remove the screw, and remove the rear cabinet. BOOT PROGRAM PCL/BUMON BARCODE FAX IMG EXT PS KANJI - Sharp MX 4501N | Installation Manual - Page 63
C. Font list Font No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Font name Code128TT-Regular -HalfThin Upc-Tall-Regular Upc-TallBarsThin-regular Upc-TallMusicThin-Regular Upc-TallNarrow-Regular Upc-TallThin-regular ZipCodeBarcode-Regular MX3500N AR-PF1 11 - 2 - Sharp MX 4501N | Installation Manual - Page 64
the network scanner expansion kit, refer to the descriptions for the "[14] Network scanner expansion kit (MX-NSX1)" in this Service Manual. A. . 1) Send image data and meta data by referring to MX-AMX1 GETTING STARTED GUIDE (package part No. 2). Check to confirm that image data and meta - Sharp MX 4501N | Installation Manual - Page 65
. 3) Insert the step screw into the mounting hole of the fax box unit. 4) Use a screw that has been removed in step 1) to secure the fax box unit. 2. Installation • Start installation from the right rear cabinet and remove the right rear cabinet. MX3500N MX-FXX1 14 - 1 - Sharp MX 4501N | Installation Manual - Page 66
the control PWB unit into the main unit and secure it with the two screws. D. Attach the FAX memory. 1) Install the FAX memory to the socket on the controller PWB as shown in the figure below so that the memory the screw. 6) Attach the ozone filter cover to the main unit. MX3500N MX-FXX1 14 - 2 - Sharp MX 4501N | Installation Manual - Page 67
detectable), other destinations China I. Clear the FAX related software switches. 1) Switch the operation panel to the copy mode and use the key operation [P], [∗], [C], and [∗] to enter the simulation mode. 2) Use the numeric keys to enter [66] in the main code entry screen shown below and press - Sharp MX 4501N | Installation Manual - Page 68
Switch the operation panel to the copy mode and use the key operation [P], [∗], [C], and [∗] to enter the simulation mode. 2) Use the numeric keys to enter [66] in the main code entry screen shown below and press the [START] key. K. Connect the line cable to the fax box unit. Connect the line cable - Sharp MX 4501N | Installation Manual - Page 69
with the machine to install the PC-FAX driver. For installing procedures, refer to the software setup guide. 4) Update the PC-FAX driver with the CD-ROM packed together with the machine. Install and setting of the driver to the PC server must be performed by the user or by the request from the - Sharp MX 4501N | Installation Manual - Page 70
model employs lead-free solder. The "LF" marks indicated on the PWB's and the Service Manual mean "Lead-Free" solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: 5mm Lead-Free Solder composition code (Refer to the table at the right.) a - Sharp MX 4501N | Installation Manual - Page 71
type ou d'un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (Swedish) VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren - Sharp MX 4501N | Installation Manual - Page 72
Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. • All other trademarks and copyrights are the property of their respective owners. SHARP CORPORATION Digital Document System Group CS Promotion Center Yamatokoriyama, Nara 639-1186, Japan 2006 November
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
 |
 |
INSTALLATION MANUAL
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CONFIGURATION
[1]
MX-3500N/4500N, MX-3501N/4501N (Main unit). . . . . . . . . . . . . . 1-1
[2]
MX-DEX3/DEX4 (Stand/1x500 sheet paper drawer,
Stand/2x500 sheet paper drawer). . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[3]
MX-TRX2 (Exit tray unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4]
MX-LCX1 (Large capacity tray). . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5]
MX-FNX1 (Finisher) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6]
MX-PNX1A/B/C/D (Punch module (For Inner Finisher)) . . . . . . . . . 6-1
[7]
MX-RBX1, MX-FNX2 (Paper pass unit, Saddle stitch finisher). . . . 7-1
[8]
AR-PN1A/B/C/D (Punch module (For Saddle stitch finisher)). . . . . 8-1
[9]
MX-FRX2, MX-FRX2U (Data security kit) . . . . . . . . . . . . . . . . . . . . 9-1
[10]
MX-PKX1 (PS3 expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11]
AR-PF1 (Barcode font kit). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[12]
MX-AMX1 (Application integration module) . . . . . . . . . . . . . . . . . 12-1
[13]
[14]
MX-FXX1 (Facsimile expansion kit) . . . . . . . . . . . . . . . . . . . . . . . 14-1
[15]
MX-FWX1 (Internet Fax expansion kit) . . . . . . . . . . . . . . . . . . . . . 15-1
1
CODE: 00ZMX3500NI1E
CONTENTS
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MODEL
MX-3500N/4500N
MX-3501N/4501N
: May 15 2006
1