Sharp MX-M200D Operation Manual - Page 89

Default Exposure, Stream Feeding, Rotation Copy, Sort Auto Select

Get Sharp MX-M200D PDF manuals and user guides View all Sharp MX-M200D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

SYSTEM SETTINGS GUIDE Select "DEFAULT TRAY SET" and press the [OK] key. The following screen will appear. DEFAULT TRAY SET TRAY 1 TRAY 2 TRAY 3 TRAY 4 1 Select the tray with the [ ] or [ ] key. 2 Press the [OK] key. DEFAULT EXPOSURE This program is used to select the exposure mode/level that is initially selected when the [EXPOSURE] key is pressed. The factory default setting is "AUTO". Select "DEFAULT EXPOSURE" and press the [OK] key. The following screen will appear. DEFAULT EXPOSURE AUTO AUTO TEXT PHOTO 1 Select the exposure mode with the [ ] or [ ] key. 2 If you selected "TEXT" or "PHOTO", set the exposure level with the [ ] or [ ] key. 3 Press the [OK] key. STREAM FEEDING When stream feeding mode is enabled, additional originals which are placed in the SPF within 5 seconds after the previous original was fed will be copied automatically. (If more than 5 seconds elapse, the [START] key ( ) must be pressed again.) This function can be used when scanning originals in copy and scan modes. The function is initially disabled (factory default setting). To enable stream feeding, select "STREAM FEEDING" and press the [OK] key so that a checkmark appears in the checkbox. To disable stream feeding, select "STREAM FEEDING" once again and press the [OK] key so that the checkmark is cleared from the checkbox. ROTATION COPY (When the dual function board is installed) If the orientation of the original does not match that of the paper, the image can be rotated. Rotation copy operates when automatic paper selection or automatic ratio selection operates. The function is initially enabled (factory default setting). Note If the image is both rotated and reduced, the position of the copied image will vary depending on the orientations of the original and the paper. Original Paper Copy To enable rotation copy, select "ROTATION COPY" and press the [OK] key so that a checkmark appears in the checkbox. To disable rotation copy, select "ROTATION COPY" once again and press the [OK] key so that the checkmark is cleared from the checkbox. SORT AUTO SELECT (When the dual function board is installed) This program is used to select the default output mode when the SPF is used for copying. The initial factory setting is "SORT". Select "SORT AUTO SELECT" and press the [OK] key. The following screen will appear. 7 SORT AUTO SELECT NO SORT SORT 1 Select the output mode with the [ ] or [ ] key. 2 Press the [OK] key. 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
87
SYSTEM SETTINGS GUIDE
7
Select "DEFAULT TRAY SET" and press the [OK] key.
The following screen will appear.
1
Select the tray with the [
] or [
] key.
2
Press the [OK] key.
DEFAULT EXPOSURE
This program is used to select the exposure
mode/level that is initially selected when the
[EXPOSURE] key is pressed.
The factory default setting is "AUTO".
Select "DEFAULT EXPOSURE" and press the [OK]
key. The following screen will appear.
1
Select the exposure mode with the [
] or
[
] key.
2
If you selected "TEXT" or "PHOTO", set
the exposure level with the [
] or [
] key.
3
Press the [OK] key.
STREAM FEEDING
When stream feeding mode is enabled, additional
originals which are placed in the SPF within 5 seconds
after the previous original was fed will be copied
automatically. (If more than 5 seconds elapse, the
[START] key (
) must be pressed again.)
This function can be used when scanning originals in
copy and scan modes.
The function is initially disabled (factory default
setting).
To enable stream feeding, select "STREAM
FEEDING" and press the [OK] key so that a
checkmark appears in the checkbox.
To disable stream feeding, select "STREAM
FEEDING" once again and press the [OK] key so
that the checkmark is cleared from the checkbox.
ROTATION COPY
(When the dual function board is installed)
If the orientation of the original does not match that of
the paper, the image can be rotated.
Rotation copy operates when automatic paper
selection or automatic ratio selection operates.
The function is initially enabled (factory default
setting).
To enable rotation copy, select "ROTATION COPY"
and press the [OK] key so that a checkmark
appears in the checkbox.
To disable rotation copy, select "ROTATION
COPY" once again and press the [OK] key so that
the checkmark is cleared from the checkbox.
SORT AUTO SELECT
(When the dual function board is installed)
This program is used to select the default output mode
when the SPF is used for copying.
The initial factory setting is "SORT".
Select "SORT AUTO SELECT" and press the [OK]
key. The following screen will appear.
1
Select the output mode with the [
] or [
]
key.
2
Press the [OK] key.
DEFAULT TRAY SET
TRAY 1
TRAY 2
TRAY 3
TRAY 4
DEFAULT EXPOSURE
AUTO
TEXT
PHOTO
AUTO
If the image is both rotated and reduced, the
position of the copied image will vary
depending on the orientations of the original
and the paper.
Note
Original
Paper
Copy
SORT AUTO SELECT
NO SORT
SORT