Sharp MX-M283N Safety Guide

Sharp MX-M283N Manual

Get Sharp MX-M283N PDF manuals and user guides View all Sharp MX-M283N manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp MX-M283N manual content summary:

  • Sharp MX-M283N | Safety Guide - Page 1
    . MODEL: MX-M283N MX-M363N MX-M453N MX-M503N CAUTIONS INSTALLATION REQUIREMENTS SUPPLIES SPECIFICATIONS INFORMATION ON DISPOSAL Keep this manual close at hand for reference whenever needed. Please see opposite side to access to "Software Setup Guide" and "Sharpdesk Installation Guide". TO
  • Sharp MX-M283N | Safety Guide - Page 2
    used with this equipment to maintain compliance with EMC regulations. The equipment should be installed near an accessible socket outlet for easy disconnection. Notice for users in the UK MAINS PLUG WIRING INSTRUCTIONS an appropriate type observing the wiring code below. DANGER: The fuse should
  • Sharp MX-M283N | Safety Guide - Page 3
    For the users of the fax function FAX interface cable and Line cable: These special accessories must be used with the device. The Declaration of Conformity can be viewed at the following URL address. http://www.sharp.de/doc/MX-FXX2.pdf 1
  • Sharp MX-M283N | Safety Guide - Page 4
    MACHINE . . 24 Factory default passwords 24 Forwarding all transmitted and received data to the administrator (document administration function). . . .24 For the users of the fax function 24 Trademark acknowledgments 25 Note: • Considerable care has been taken in preparing this manual. If you
  • Sharp MX-M283N | Safety Guide - Page 5
    manual To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are classified as explained below. Be sure you understand the meaning of the symbols when reading the manual casing. High-voltage parts inside the machine authorised service representative. Using the
  • Sharp MX-M283N | Safety Guide - Page 6
    the printer during to place the copier in a ventilated a misfeed, performing maintenance, closing the front use the machine for a long time, be sure to remove the power plug from the outlet for safety. Store toner, toner containers (toner cartridges), and waste toner Sharp Corporation bears no responsibility for
  • Sharp MX-M283N | Safety Guide - Page 7
    nm ±10 nm MX-M283N/MX-M363N: 6.1 µs ±8.3 ns /7 mm MX-M453N/MX-M503N: 4.8 µs ±6.4 ns /7 mm Max 0.6 mW (LD1+LD2) Caution Use of controls or SHARP DEALER OR AUTHORISED SERVICE REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY. Each instruction also covers the optional units used with
  • Sharp MX-M283N | Safety Guide - Page 8
    room with a ventilation fan or windows that provide sufficient air circulation. (The humidifiers, air conditioners, etc.) Plastic parts may become deformed and dirty output page 10) If the location has an ultrasonic humidifier, use pure water for humidifiers in the humidifier. If tap water is used
  • Sharp MX-M283N | Safety Guide - Page 9
    for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher staple cartridge, and transparency film. For best copying
  • Sharp MX-M283N | Safety Guide - Page 10
    ), 600 x 400 dpi, 600 x 600 dpi Scanning resolution Automatic document feeder 600 x 300 dpi (factory default values), 600 x 400 dpi, 600 x 600 dpi (MX-M363N/MX-M453N/MX-M503N) Automatic document feeder (MX-M283N) 600 x 400 dpi (factory default values), 600 x 600 dpi Printing resolution 1200
  • Sharp MX-M283N | Safety Guide - Page 11
    lbs. index)) Paper types: SHARP-recommended plain paper, recycled paper, supports use the connectors simultaneously. When a keyboard is not connected (MX-KBX2), only one connector can be used; simultaneous use is not possible. If you need to change the connector that is used, contact your service
  • Sharp MX-M283N | Safety Guide - Page 12
    SPECIFICATIONS Continuous copying speeds* Model MX-M283N MX-M363N MX-M453N MX-M503N Copy ratio 100% / Reduced / Enlarged A3, 11" copies when performing continuous one-sided copying of the same page (excluding offset output) using plain one-sided paper from a tray other than the bypass
  • Sharp MX-M283N | Safety Guide - Page 13
    lbs.) MX-M363N/MX-M453N/MX-M503N: One-sided 35 g/m2 to 128 g/m2 (9 lbs. to 32 lbs.)*2 Two-sided 50 g/m2 to 128 g/m2 (13 lbs. to 32 lbs.) 100 sheets (80 g/m2 (21 lbs.)), Maximum stack height of 13 mm (1/2") *1 Scanning in mono 2 mode of one side only is possible in fax and scan send
  • Sharp MX-M283N | Safety Guide - Page 14
    (right tray) specifications Model MX-TRX2 Output method Face-down output Output capacity* 100 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper) Dimensions When tray is folded up: 314 mm (W) x 405 mm (D) x 52 mm (H) (12-23/64" (W) x 15-61/64" (D) x 2-3/64" (H)) When tray is extended
  • Sharp MX-M283N | Safety Guide - Page 15
    to 110 lbs. index)) 500 sheets (80 g/m2 (21 lbs.)) x 2 tray SHARP-recommended plain paper, recycled paper, and coloured paper When "Auto-AB" detection is tray specifications* Model MX-LCX1 Paper sizes A4, 8-1/2" x 11" (paper size change must be performed by a service technician) Paper weight
  • Sharp MX-M283N | Safety Guide - Page 16
    SPECIFICATIONS Finisher specifications Model MX-FNX9 Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, envelopes, 12" x 18", 11" x 17", 8-1/2" 71 mm (2-51/64"). *4 The height of the sheets must not exceed 35.5 mm (1-13/32"). *5 The maximum number of sheets for stapling assumes a paper weight
  • Sharp MX-M283N | Safety Guide - Page 17
    SPECIFICATIONS Finisher (large stacker) specifications*1 Model MX-FN11 Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, envelopes, 12" x -25/64" (W) x 25-25/64" (D) x 43-19/64" (H)) (When tray is extended) Weight Approx. 45 kg (99.3 lbs.) Stapler section Allowed paper sizes for stapling A3,
  • Sharp MX-M283N | Safety Guide - Page 18
    SPECIFICATIONS Saddle stitch finisher specifications*1 Model MX-FN10 Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, envelopes, 12" x 18", 11" x 17 175 mm (6-57/64"). *5 The height of the sheets must not exceed 94 mm (3-45/64"). *6 The maximum number of sheets for stapling assumes a paper weight
  • Sharp MX-M283N | Safety Guide - Page 19
    finisher Dimensions 105 mm (W) x 518 mm (D) x 170 mm (H) (4-9/64" (W) x 20-25/64" (D) x 6-45/64" (H)) Weight Approx. 3.5 kg (7.7 lbs.) Punch module specifications (for finisher (large stacker)) Model MX-PNX6A MX-PNX6B MX-PNX6C MX-PNX6D Hole punching 2 holes 2 holes or 3 holes 4 holes
  • Sharp MX-M283N | Safety Guide - Page 20
    dpi Printer driver type PCL5e, PCL6, PostScript 3 compatible*1, XPS*2 Supported protocols TCP/IP, IPX/SPX, NetBEUI, EtherTalk*1 Supported client PC operating systems See "VERIFYING SYSTEM REQUIREMENTS" in the Software Setup Guide / Sharpdesk Installation Guide. Fonts PCL5e, PCL6 PostScript
  • Sharp MX-M283N | Safety Guide - Page 21
    to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax, and Group) Pull scan function (TWAIN) specifications Supported protocol Supported client PC operating systems Colour modes Resolution settings Scanning area TCP/IP (IPv4) Windows 98 / Me / 2000 / XP / Server 2003
  • Sharp MX-M283N | Safety Guide - Page 22
    mm (11-45/64") x max. length 1000 mm (39-23/64") can be transmitted using the automatic document feeder. Scanning one side is programs) F-code transmission Supported (SUB/SEP (sub-address) and Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax and Group)
  • Sharp MX-M283N | Safety Guide - Page 23
    the homepage of www.swico.ch or www.sens.ch. B. Information on Disposal for Business Users. 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be
  • Sharp MX-M283N | Safety Guide - Page 24
    22
  • Sharp MX-M283N | Safety Guide - Page 25
    Contact at: ✂ Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator's contact information in the left hand margin.)
  • Sharp MX-M283N | Safety Guide - Page 26
    users admin ✂ Forwarding all transmitted and received data to the administrator (document administration function) This function is used to forward all data transmitted and received by the machine to a specified destination (Scan to E-mail address, Scan to FTP destination, Scan to Network Folder
  • Sharp MX-M283N | Safety Guide - Page 27
    used in conjunction with the machine and its peripheral devices and accessories. • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows Server® 2003, Windows Vista®, Windows the Adobe PDF logo, and Sharp Corporation. • Sharp OSA is a trademark of Sharp
  • Sharp MX-M283N | Safety Guide - Page 28
  • Sharp MX-M283N | Safety Guide - Page 29
  • Sharp MX-M283N | Safety Guide - Page 30
    to directly receive image data from the Digital Laser Copier/Printer. ● If a user-created file is saved in the Sharpdesk desktop folder, the Sharpdesk desktop folder will not be deleted when Sharpdesk is uninstalled. ● If you uninstall Sharpdesk Imaging in Windows 98/Me/2000, you will not be able to
  • Sharp MX-M283N | Safety Guide - Page 31
    the on-screen instructions to create an index database. For detailed information, see the Sharpdesk Installation Guide and Sharpdesk User's Guide. * Sharpdesk Imaging is a version of Eastman Software's Imaging for Windows Professional Edition that has been customized by the Sharp Corporation. 48
  • Sharp MX-M283N | Safety Guide - Page 32
    of the software programs in the user's guides and on the Information screen during installation. ● The user's guides give detailed instructions for installing and setting up the programs. Be sure to read the user's guides before installing the programs. In particular, if you are going to use Network
  • Sharp MX-M283N | Safety Guide - Page 33
    -ROM (for Windows) User's Guides for Software Programs The Manual folder in the CD-ROM contains user's guides (in PDF format) for each of the software programs. ● Sharpdesk Installation Guide ● Sharpdesk User's Guide ● Network Scanner Tool User's Guide ● SHARP TWAIN AR/DM User's Guide In addition to
  • Sharp MX-M283N | Safety Guide - Page 34
    size. (To view a PDF file saved using a high compression ratio, the latest version of Adobe Reader is required.) Network Scanner Tool This is a utility that helps you use Scan to Desktop. It configures the necessary settings in the Digital Laser Copier/Printer and client computer to receive data. In
  • Sharp MX-M283N | Safety Guide - Page 35
    to the use of this operation manual. Table of Contents Sharpdesk CD-ROM (for Windows 45 Software Programs ...45 Sharpdesk (Desktop Document Management Software 45 Network Scanner Tool ...45 SHARP TWAIN AR/DM ...45 User's Guides for Software Programs ...46 Installing the Software Program ...47
  • Sharp MX-M283N | Safety Guide - Page 36
    REMOVING THE SOFTWARE To remove the printer driver or software installed using the installer, follow the steps below. Windows Mac OS X 1 Click the [start] button and then click [Control Panel]. In Windows 98/Me/NT 4.0/2000, click the [Start] button, point to [Settings], and click [Control Panel
  • Sharp MX-M283N | Safety Guide - Page 37
    WHEN INSTALLATION WAS NOT SUCCESSFUL Problem The printer driver is not installed correctly by plug and play (USB connection in Windows). Point to check Did you connect the machine to your computer before installing the printer driver? Solution In Windows 2000/XP/Server 2003/Vista/Server 2008, if
  • Sharp MX-M283N | Safety Guide - Page 38
    ] key ( ) in that order. (In Windows, search again after powering on the machine.) Make sure that the cable is connected securely to the LAN connectors on your computer and the machine. Check the connections at the hub as well. ☞ CONNECTING TO A NETWORK (page 7) When a USB cable is connected, make
  • Sharp MX-M283N | Safety Guide - Page 39
    2000/XP/Server 2003 42 Problem The software cannot be installed. The machine is not detected (when connected to a network). Point to check Is there sufficient free space on your hard drive? Are you using an operating system that is not supported? Is the IP address of the machine configured? Is
  • Sharp MX-M283N | Safety Guide - Page 40
    of step 12 to close the window. 15 Click the close box ( ) to close the "Chooser". This completes the configuration of the printer driver. Installing the screen fonts The screen fonts for Mac OS 9.0 - 9.2.2 are contained in the [Font] folder of the "PRINTER UTILITIES" CD-ROM that accompanies the
  • Sharp MX-M283N | Safety Guide - Page 41
    printer. (2) Click the machine's model name. The machine's model name usually appears as [SCxxxxxx]. ("xxxxxx" is a sequence of characters that varies depending on your model.) (3) Click the [Create] button. 6 The License Agreement window software. Next, configure the printer driver settings. 38
  • Sharp MX-M283N | Safety Guide - Page 42
    quality image than a fax. If you wish to use the IPP function, follow these steps to select the PPD file when configuring the printer driver (step 14 on page 35). v10.4.11, v10.5 - 10.5.5 v10.2.8, v10.3.9 (1) (1) (2) (2) (3) (4) (1) Click the [IP Printer] icon. If you are using Mac OS X v10
  • Sharp MX-M283N | Safety Guide - Page 43
    Driver] tab and go to step 16. (2) Click [Show Info]. If you are using Mac OS X v10.2.8, select [Show Info] from the [Printers] menu. 16 Select the machine configuration button. If you are using Mac OS X v10.5 to 10.5.5, click the [OK] button. (4) Click to close the window. You can check the
  • Sharp MX-M283N | Safety Guide - Page 44
    the IPP function. If you wish to use the IPP function, see "Printing using the IPP function" (page 37) to configure the printer driver settings. v10.4.11, v10.5 - 10.5.5 v10.2.8, v10.3.9 (1) (1) (2) (2) (3) (4) (1) Click the [Default Browser] icon. • If multiple AppleTalk zones are displayed
  • Sharp MX-M283N | Safety Guide - Page 45
    "Authenticate" window appears, enter the password and click the [OK] button. 10 When the message "The software was successfully installed" appears in the installation window, click the [Close] button. This completes the installation of the software. Next, configure the printer driver settings. 34
  • Sharp MX-M283N | Safety Guide - Page 46
    MAC OS 9.0 - 9.2.2: page 38 • The PS3 expansion kit is required to use the machine as a printer in a Macintosh environment. In addition, the machine must be connected to a network. A USB connection cannot be used. • The scanner driver and PC-Fax driver cannot be used in a Macintosh environment. MAC
  • Sharp MX-M283N | Safety Guide - Page 47
    [Close] button in the screen of step 2. When using a port created with "Standard TCP/IP Port" When using a port created using "Standard TCP/IP Port" in Windows 2000/XP/Server 2003/Vista/Server 2008, in the screen that appears after you click the [Configure Port] button in the screen of step 3, make
  • Sharp MX-M283N | Safety Guide - Page 48
    THE PORT" (page 29). 5 Select [Custom] and click the [Settings] button. 2 Select [Standard TCP/IP Port] and then click the [New Port] button. 3 Click the [Next] button. 4 Enter the machine's IPv6 address in [Printer Name or IP Address] and click the [Next] button. 6 Configure the port settings
  • Sharp MX-M283N | Safety Guide - Page 49
    network (WAN) using the IPP function, select [SC-Print2005 Port], click the [New Port] button (the [OK] button in Windows 98/Me), and follow the on-screen instructions to create the port again. (1) (2) (3) (4) (1) Enter the machine's IP address. ☞ Checking the IP address of the machine (page
  • Sharp MX-M283N | Safety Guide - Page 50
    THE PORT When using the machine in a Windows environment, follow the steps below to change the port when you have changed the IP address of the machine or have installed the PC-Fax driver when the machine is connected with a USB cable. If the machine is being used on an IPv6 network, follow the
  • Sharp MX-M283N | Safety Guide - Page 51
    the PS printer driver. 1 Insert the "PRINTER UTILITIES" CD-ROM that accompanies the PS3 expansion kit into your computer's CD-ROM drive. 6 Click the [PS Display Font] button. 2 Click the [Start] button ( ), click [Computer], and then double-click the [CD-ROM] icon ( ). • In Windows XP/Server 2003
  • Sharp MX-M283N | Safety Guide - Page 52
    port number used by the scanner function of the machine has been changed, enter a colon ":" following the IP address and then enter the port number. (Normally the port number does not need to be entered.) INSTALLING THE SCANNER DRIVER 8 Click the [OK] button. This completes the configuration of
  • Sharp MX-M283N | Safety Guide - Page 53
    be used when the machine is connected to a network. When the scanner driver is installed, PC scan mode of the image send function can be used. Supported operating systems: Windows 98/Me/2000*/XP*/Server 2003*/Vista*/Server 2008* * Administrator's rights are required to install the software. After
  • Sharp MX-M283N | Safety Guide - Page 54
    by a USB cable. • When printing to the machine using the IPP function. Supported operating systems: Windows 98/Me/NT 4.0*/2000*/XP*/Server 2003*/Vista*/Server 2008* * Administrator's rights are required to install the software. When the software selection screen appears in step 6 of "OPENING THE
  • Sharp MX-M283N | Safety Guide - Page 55
    [Control Panel], and then click [Printer]. • In Windows XP/Server 2003, click the [start] button and then click [Printers and Faxes]. • In Windows 98/Me/NT 4.0/2000, click the [Start] button, select [Settings], and then click [Printers]. 3 Configure the printer driver for the options installed on
  • Sharp MX-M283N | Safety Guide - Page 56
    . If a user type name (1 to 7) was changed, enter the changed name. Set Tandem Print*: Enter the setting (the IP address of the slave machine) in "Tandem Connection Setting" in the system settings (administrator) of the machine. * "Set Tandem Print" can only be configured when the printer driver is
  • Sharp MX-M283N | Safety Guide - Page 57
    detected machine status. 2 Open the printer properties window. (1) Right-click the printer driver icon of the machine. (2) Select [Properties]. If the machine is being used on an IPv6 network, you must configure the options manually as explained in "If automatic configuration fails" (page 23). 22
  • Sharp MX-M283N | Safety Guide - Page 58
    below to install the PPD driver using the Add Printer Wizard. • The CD-ROM does not include software for Windows 98/Me/NT 4.0. Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0. • If you are using Windows 2000/XP/Server 2003/Vista/Server
  • Sharp MX-M283N | Safety Guide - Page 59
    SCREEN (FOR ALL SOFTWARE)" (page 8), perform the steps below. 1 Click the [Printer Driver] button. To install the PC-Fax driver, click the [PC-Fax Driver] button on the "Disc 2" CD-ROM. 4 Select the printer name (configured as a shared printer). * The above screen appears when using the "Disc
  • Sharp MX-M283N | Safety Guide - Page 60
    " (page 22) to configure the printer driver settings. • Make sure that the port of the installed driver is the same as the port used by the PCL6 printer driver. The port used by the printer driver of the machine is indicated by a checkmark on the [Ports] tab of the printer driver properties window
  • Sharp MX-M283N | Safety Guide - Page 61
    ( ) appears. 18 • When the PC-Fax driver is being installed, this screen does not appear. Go to the next step. • The PS3 expansion kit is required to use the PS printer driver or the PPD driver. • The [PPD] checkbox only appears if you are using Windows 2000/XP/Server 2003/Vista/Server 2008.
  • Sharp MX-M283N | Safety Guide - Page 62
    USB cable. 8 Installation of the PCL6 printer driver begins. When the "Found New Hardware Wizard" appears, select [Install the software automatically (Recommended)], click the [Next] button, and follow the on-screen instructions. • If you are using Windows Vista/Server 2008 If a security warning
  • Sharp MX-M283N | Safety Guide - Page 63
    WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0)" (page 21) and install the driver using the Add Printer Wizard. • To use the port created when the printer driver is installed for fax data transfer, install the printer driver first and then install the PC-Fax driver. When the software selection
  • Sharp MX-M283N | Safety Guide - Page 64
    INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER 5 Enter the machine's URL and click the [Next] button. Enter the URL in the following format: Normal format: http://
  • Sharp MX-M283N | Safety Guide - Page 65
    To configure the settings, see "7. SYSTEM SETTINGS" in the Operation Guide. When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 8), perform the steps below. 1 Click the [Printer Driver] button. To install the PC-Fax driver, click
  • Sharp MX-M283N | Safety Guide - Page 66
    Follow the on-screen instructions. Read the message in the window that appears and click the [Next] button. Installation begins. • When the PC-Fax driver is being installed, this screen does not appear. Go to the next step. • The PS3 expansion kit is required to use the PS printer driver or the PPD
  • Sharp MX-M283N | Safety Guide - Page 67
    THE PRINTER DRIVER / PC-FAX DRIVER X Installation by specifying the machine's address When the machine cannot be found because it is not powered on or otherwise, installation is possible by entering the name (host name) or IP address of the machine. If the machine is being used on an IPv6 network
  • Sharp MX-M283N | Safety Guide - Page 68
    kit. See "INSTALLING THE PS DISPLAY FONTS" (page 28). • If you are using the machine as a shared printer, see "USING THE MACHINE AS A SHARED PRINTER" (page 20) to install the printer driver on each of the client computers. 7 Follow the on-screen instructions. Read the message in the window
  • Sharp MX-M283N | Safety Guide - Page 69
    [Next] button. • When the PC-Fax driver is being installed, this screen does not appear. Go to the next step. • The PS3 expansion kit is required to use the PS printer driver or the PPD driver. • The [PPD] checkbox only appears if you are using Windows 2000/XP/Server 2003/Vista/Server 2008. • If
  • Sharp MX-M283N | Safety Guide - Page 70
    PC-Fax driver when the machine is connected to a Windows network (TCP/IP network). Supported operating systems: Windows 98/Me/NT 4.0*/2000*/XP*/Server 2003*/Vista*/Server 2008* * Administrator's rights are required to install the software. • The PS3 expansion kit is required to use the PS printer
  • Sharp MX-M283N | Safety Guide - Page 71
    , see the appropriate page below for the software that you are installing. INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER • WHEN THE MACHINE IS CONNECTED TO A NETWORK* - Standard installation: page 9 - Installation by specifying the machine's address: page 12 - Printing using the IPP function and
  • Sharp MX-M283N | Safety Guide - Page 72
    , be sure to configure the IP address and other network settings before installing the software. (The factory default setting for the IP address is to receive the IP address automatically when the machine is used in a DHCP environment.) Network settings can be configured using "Network Settings" in
  • Sharp MX-M283N | Safety Guide - Page 73
    this manual. Operating system environment*1 Software Required expansion kits Windows PCL6 printer driver, PCL5e printer driver Can be used in the standard configuration. PS printer driver, PPD driver PC-Fax driver*2 PS3 expansion kit Facsimile expansion kit*3 Scanner driver Printer Status
  • Sharp MX-M283N | Safety Guide - Page 74
    PC-Fax driver and scanner driver cannot be used. • For users of Windows 98/Me/NT 4.0 The CD-ROM does not include software for Windows 98/Me/NT 4.0. Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0. • For users of Windows NT 4.0/2000/XP
  • Sharp MX-M283N | Safety Guide - Page 75
    FONTS (page 28) X "PRINTER UTILITIES" CD-ROM that accompanies the Internet fax expansion kit (for Windows) This CD-ROM is used to update the PC-Fax driver on the "Software CD-ROM" so that it can be used to send Internet faxes (PC-I-Fax function). If you wish to use the PC-I-Fax function, first
  • Sharp MX-M283N | Safety Guide - Page 76
    fax expansion kit to enable you to send a file from your computer as an Internet fax in the same way as you print a file. ☞ INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER (page 9) The following software can be used only when the machine is connected to a network. • Scanner driver (TWAIN driver
  • Sharp MX-M283N | Safety Guide - Page 77
    languages. It is recommended that you use the PCL6 printer driver. If you have a problem printing from older software using the PCL6 printer driver, use the PCL5e printer driver. - PS printer driver The PS printer driver supports the PostScript 3 page description language developed by Adobe Systems
  • Sharp MX-M283N | Safety Guide - Page 78
    THE PRINTER DRIVER / PC-FAX DRIVER 9 • WHEN THE MACHINE IS CONNECTED TO A NETWORK 9 • WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE 16 • USING THE MACHINE AS A SHARED PRINTER 20 • USING THE STANDARD WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0) . . . 21 • CONFIGURING THE PRINTER DRIVER
  • Sharp MX-M283N | Safety Guide - Page 79
    a computer. This manual also explains how to install the printer drivers and software that are used when the expansion kits are installed, and how to install the scanner driver. If the software is not installed correctly or you need to remove the software, see "4. TROUBLESHOOTING" (page 40). Please
  • Sharp MX-M283N | Safety Guide - Page 80
    M283N MX-M363N MX-M453N MX-M503N DIGITAL MULTIFUNCTIONAL SYSTEM Software Setup Guide Please keep this manual as the information mentioned below is very important. Sharpdesk Serial Numbers BEFORE INSTALLING THE SOFTWARE SETUP IN A WINDOWS ENVIRONMENT SETUP IN A MACINTOSH ENVIRONMENT TROUBLESHOOTING
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
DIGITAL MULTIFUNCTIONAL SYSTEM
Safety Guide
Safety Guide
Safety Guide
Before installing this product, be sure to read the
"CAUTIONS" and "INSTALLATION
REQUIREMENTS" sections.
Keep this manual close at hand for reference
whenever needed.
MX-M283N
MX-M363N
MX-M453N
MX-M503N
MODEL:
SPECIFICATIONS
INFORMATION ON DISPOSAL
SUPPLIES
INSTALLATION REQUIREMENTS
CAUTIONS
TO THE ADMINISTRATOR OF THE MACHINE
Please see opposite side to access
to "Software Setup Guide" and "Sharpdesk
Installation Guide".
These manuals are combined for environmental protection.