Sharp UN552VS/UN552VS-TMX4P External Control Codes for the
Sharp UN552VS/UN552VS-TMX4P Manual
 |
View all Sharp UN552VS/UN552VS-TMX4P manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp UN552VS/UN552VS-TMX4P manual content summary:
- Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 1
External Control NEC LCD Monitor INDEX Rev.1.3 (G4) I. Application...4 II. Preparation ...4 2. Connectors and wiring ...4 2.1 RS-232C Remote control...4 2.2 LAN control ...5 III. Communication specification ...6 3. Communication Parameter ...6 3.1 RS-232C Remote control...6 3.2 LAN - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 2
9.2 Date & Time Write ...55 10. Schedule read and write ...58 10.1 Schedule Read...58 10.2 Schedule Write ...62 11. Holiday read and write ...70 11.1 Holiday Read...70 11.2 Holiday Write ...72 12. Weekend read and write ...75 12.1 Weekend Read ...75 12.2 Weekend Write...77 13. Self diagnosis ...79 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 3
21.5 Auto Tile Matrix Reset ...108 22. Power Save Mode ...109 22.1 Power Save Mode Read ...109 22.2 Power Save Mode Write ...111 22.3 Auto Power Save Time Read ...113 22.4 Auto Power Save Time Write ...114 22.5 Auto Standby Time Read ...115 22.6 Auto Standby Time Write ...116 23. Setting Copy ...117 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 4
control Connector: 9-pin D-Sub Cable: Cross (reversed) cable or null modem cable (Please refer "Controlling the LCD monitor via RS-232C Remote control" on User's manual.) (4/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 5
2.2 LAN control Connector: RJ-45 10/100 BASE-T Cable: Category 5 or higher LAN cable (Please refer "Controlling the LCD monitor via LAN control" on User's manual.) (5/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 6
Transport layer (TCP) * Using the payload of TCP segment. (Default) Automatic setup * If you need to change, Please refer "Network settings" on User's manual. 7142 (Fixed) (Note) The monitor will disconnect the connection if no packet data is received for 15 minutes. And the controller (PC) has to - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 7
4. Communication Format Header Message Check Code Delimiter The command packet consists of four parts, Header, Message, Check code and Delimiter. Note: Don't add extra data (Example: padding data) after Delimiter. Recommended sequence of a typical procedure to control a monitor is as follows, [A - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 8
4.1 Header block format (fixed length) Header Message Check code Delimiter SOH Reserved Destination '0' 1st 2nd 3rd 1stbyte) SOH: Start of Header ASCII SOH (01h) Source 4th Message Type 5th Message Length 6th -7th 2ndbyte) Reserved: Reserved for future extensions. On this monitor, it - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 9
Ex.) If you want to control a monitor that has the "ID No." as '1', specify a destination address 'A'(41h). If you want to control all of the monitors which are connected by a daisy chain, specify a destination address '*'(2Ah). 4thbyte) Source: Source equipment ID. (Sender) Specify a sender address - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 10
4.2 Message block format Header Message Check code Delimiter "Message block format" is allied to the "Message Type" in the "Header". Refer to the section 4.1 "Header block format" for more detail. 1)Get current parameter The controller sends this message when you want to get the status of the - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 11
to section 5.5 "Commands message" for more details. 6)Command reply The monitor replies to a query from the controller. "Command reply message" format depends on each command. Refer to section 5.5 "Commands message" for more details. (11/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 12
4.3 Check code Header Message Check code Delimiter Check code is the Block Check Code (BCC) between the Header and the End of Message except SOH. SOH D0 Reserved D1 Destination D2 Source D3 Type D4 Length(H) D5 Length(L) D6 STX D7 Data D8 | | | | ETX Dn Check code Dn+1 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 13
4.4 Delimiter Header Message Packet delimiter code; ASCII CR(0Dh). Check code Delimiter (13/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 14
5. Message type 5.1 Get current Parameter from a monitor. STX OP code OP code ETX page Hi Lo Hi Lo 1st 2nd-3rd 4th-5th 6th Send this message when you want to get the status of a monitor. For the status that you want to get, specify the "OP code page" the "OP code", refer to "Appendix A. - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 15
5.2 "Get parameter" reply STX Result OP code OP code Type Max value Current Value ETX page Hi Lo Hi Lo Hi Lo Hi Lo MSB LSB MSB LSB 1st 2nd-3rd 4th-5th 6th -7th 8th -9th 10th -13th 14th -17th 18th The monitor replies with a current value and the status of the requested item ( - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 16
18thbyte) ETX: End of Message ASCII ETX (03h) (16/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 17
5.3 Set parameter STX OP code OP code Set Value ETX page Hi Lo Hi Lo MSB LSB 1st 2nd-3rd 4th-5th 6th-9th 10th Send this message to change monitor's adjustment and so on. The controller requests a monitor to change value. 1stbyte) STX: Start of Message ASCII STX (02h) 2nd-3rdbytes) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 18
5.4 "Set parameter" reply STX Result OP code page Hi Lo Hi Lo 1st 2nd-3rd 4th-5th OP code Hi Lo 6th-7th Type Hi Lo 8th-9th Max value MSB LSB 10th-13th Requested setting ETX Value MSB LSB 14th -17th 18th The Monitor echoes back the parameter and status of the requested operation - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 19
5.5 Commands "Command message format" depends on each command. Some commands are shown with usage. Refer to section 7 to 25. 5.5.1 Save Current Settings. The controller requests for the monitor to store the adjusted value. STX Command code '0' 'C' ETX Send "OC"(30h, 43h) as Save current - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 20
5.5.2 Get Timing Report and Timing reply. The controller requests the monitor to report the displayed image timing. STX Command code '0' '7' ETX Send "07"(30h, 37h) as Get Timing Report command. Complete "Get Timing Report" command packet as follows; ASCII: 01h-30h-41h-30h-41h-30h-34h- - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 21
5.5.3 NULL Message STX Command code 'B' 'E' ETX The NULL message returned from the monitor is used in the following cases; To tell the controller that the monitor does not have any answer to give to the host (not ready or not expected) A null message will be returned by the monitor if the - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 22
the "Backlight" setting. Step 1. The controller requests the Monitor to reply with the current brightness setting and capability to support this operation. (Get parameter) Header SOH-'0'-Monitor ID'0'-'C'-'0'-'6' Message STX-'0'-'0'-'1'-'0'-ETX Check code BCC Delimiter CR Header SOH (01h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 23
BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet Step 3. The controller request the monitor to change the Backlight setting Header SOH-'0'-Monitor ID'0'-'E'-'0'-'A' Message STX-'0'-'0'-'1'-'0''0'-'0'-'5'-'0'-ETX Check code BCC - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 24
CR (0Dh): End of packet Repeat Step 1 and Step 2, if you need to check the Backlight setting. (Recommended) Step 5. Request the monitor to store the Backlight setting. (Save Current Settings Command) Header SOH-'0'-Monitor ID'0'-'A'-'0'-'4' Message STX-'0-'C'-ETX Check code BCC Delimiter CR - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 25
6.2. How to read the measurement value of the built-in temperature sensors. Target displays have three built-in temperature sensors. The controller can monitor inside temperatures by using those sensors with external control. The following shows the procedure for reading the temperatures from the - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 26
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet Step 3. The controller requests the monitor to send the temperature from the selected sensor. Header SOH-'0'-Monitor ID'0'-'C'-'0'-'6' Message STX-'0'-'2'-'7'-'9'-ETX - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 27
+125.0 + 25.0 + 0.5 0 - 0.5 - 25.0 - 55.0 0000 0000 1111 1010 0000 0000 0011 0010 0000 0000 0000 0001 0000 0000 0000 0000 1111 1111 1111 1111 1111 1111 1100 1110 1111 1111 1001 0010 00FAh 0032h 0001h 0000h FFFFh FFCEh FF92h ETX (03h): End of Message Check code BCC: Block Check Code Refer to the - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 28
6.3. Operation Code (OP code) Table 1) SPECTRAVIEW ENGINE Setting = OFF Item INPUT OP code OP code page 00h 60h INPUT PICTURE GAMMA PICTURE MODE 02h 1Ah BRIGTNESS BACKLIGHT BRIGHTNESS GAMMA CORRECTION 00h 10h 00h 92h 02h 68h AUTO HDE SELECT *2 11h B2h COLOR 02h 1Fh COLOR - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 29
ADJUST *1 Item COLOR CONTROL HUE CONTRAST SHARPNESS AUTO SETUP AUTO ADJUST H POSITION V POSITION CLOCK PHASE H RESOLUTION V RESOLUTION COLOR SYSTEM *1 OP code page 00h 00h OP code RED: 9Bh YELLOW: 9Ch GREEN: 9Dh CYAN: 9Eh BLUE: 9Fh MAGENTA: A0h 90h 00h 12h 00h 8Ch 00h 1Eh 10h B7h 00h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 30
ASPECT Item INPUT RESOLUTION *1 UHD UPSCALING *2 ASPECT ZOOM OP code OP code page 02h DAh 11h 09h 02h 70h 11h 2Ch Parameter Input Resolution select 0:No mean 1:Item 1(always Auto) 2:Item 2 3:Item 3 4:Item 4 5:Item 5 Ex) Item 1= AUTO Item 2= -- / 1024x768 / 1400x1050 / 800x600 / 1280x960 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 31
Item H ZOOM OP code OP code page 11h 2Dh Parameter 0-89(59h): No mean 90(5Ah): 90% 91(5Bh): 91% | 100(64h): 100% | 300(12Ch): 300% V ZOOM 11h 2Eh 0-89(59h): No mean 90(5Ah): 90% 91(5Bh): 91% | 100(64h): 100% | 300(12Ch): 300% H POS 02h V POS 02h OVER SCAN 02h DEINTERLACE 02h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 32
SCHDULE SCHEDULE AUDIO AUDIO DELAY EQULIZER BALANCE Item VOLUME BALANCE SURROUND TREBLE BASS AUDIO INPUT MULTI PICTURE AUDIO LINE OUT AUDIO DELAY DELAY TIME RESET (AUDIO) ENABLE DISABLE SCHEDULE SETTINGS OP code OP code page 00h 62h 00h 93h 00h 94h 02h 34h 00h 8Fh 00h 91h 02h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 33
ACTIVE PICTURE Item HOLIDAY SETTINGS WEEKEND SETTINGS DATE & TIME DAYLIGHT SAVING OFF TIMER RESET (SCHEDULE) KEEP MULTI PICTURE MODE MULTI PICTURE MODE ACTIVE ACTIVE FRAME PICTURE1 PICTURE2 PICTURE SIZE X Y OP code OP code Parameter page Refer to chapter 11 Refer to chapter 12 Refer to - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 34
CUSTOM DETECT TEXT TICKER ROTATE *2 Item ASPECT ROTATE ALL PICTURE1 PICTURE2 PICTURE3 PICTURE4 MODE POSITION SIZE DETECT PICTURE1 PICTURE2 INPUT DETECT PRIORITY1 PRIORITY2 PRIORITY3 INPUT CHANGE OP code OP code page 10h 83h 11h 16h 11h 12h 11h 13h 11h 14h 11h 15h 10h 08h 10h 09h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 35
OS D TERMINAL SETTING EQUALIZER *1 SUPER Item INPUT1 INPUT2 DVI MODE *1 VGA MODE *1 SYNC TYPE *1 DisplayPort HDMI SIGNAL SLOT2 DisplayPort1 HDMI VIDEO LEVEL RESET (MULTI INPUT) LANGUAGE OP code OP code page 10h CEh 10h CFh 02h CFh 10h 8Eh 11h 95h 10h F1h/F2h 10h 40h 11h 90h 11h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 36
MULTI DISPLAY TILE MATRIX OSD POSITION Item MENU DISPLAY TIME X Y INFORMATION OSD OSD TRANSPARENCY OSD ROTATION KEY GUIDE MEMO INPUT NAME NAME RESET CLOSED CAPTION RESET (OSD) AUTO TILE MATRIX SETIP SETTING COPY H MONITOR V MONITOR POSITION TILE COMP H SIZE OP code OP code - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 37
Item V SIZE H ADJUSTMENT V ADJUSTMENT ENABLE TILE MATRIX MEM MONITOR ID GROUP ID AUTO ID AUTO ID RESET RESET (MULTI DISPLAY) POWER SAVE POWER SAVE MESSAGE11h COOLING FAN FAN SPEED SENSOR1 SENSOR2 SENSOR3 OP code OP code page 11h 97h 11h 98h 11h 99h 02h D3h 10h 4Ah Parameter 0: Small | - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 38
CONTROL IR LOCK SETTING POWER ON DELAY SCREEN SAVER MOTION HEAT STATUS Item FAN1/2/3 BACKLIGHT TEMPERATURE SENSOR1/2/3 GAMMA BACKLIGHT INTERVAL ZOOM SIDE BORDER COLOR DELAY TIME LINK TO ID RESET (DISPLAY PROTECTION) IP ADDRESS SETTING CHANGE PASSWORD SECURITY MODE SELECT OP code page 02h OP - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 39
KEY LOCK SETTING Item POWER VOLUME MIN VOL MAX VOL INPUT UNLOCK SELECT CHANNEL MODE SELECT POWER VOLUME MIN VOL MAX VOL INPUT CHANNEL OP code OP code page 10h D5h 10h D6h 10h D7h 10h D8h 10h D9h 10h DAh 10h DBh 10h DCh 10h D9h 11h 6Ah 11h 6Bh 11h 6Ch 11h 6Dh 11h 6Eh - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 40
INPUT SELECT Item DDC/CI OP code OP code page 10h BEh PING IP ADDRESS RESET AUTO BRIGHTNESS 02h 2Dh BACKLIGHT DIMMING *2 11h 4Eh MODE 10h C8h ROOM LIGHT SENSING BACKLIGHT SETTING MAX LIMIT IN BRIGHT 10h C9h 10h 33h IN DARK 10h 34h SENSING LUX 02h B4h MODE 10h 75h AUTO - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 41
OPTION INTERNAL PC Item WAITING TIME POWER INDICATOR POWER INDICATOR SCHEDULE INDICATOR INTELLI WIRELESS DATA TOUCH POWER EXTERNAL CONTROL PC SOURCE US B CE C USB POWER CEC AUTO TURN OFF AUDIO RECEIVER SEARCH DEVICE RESET (CONTROL) OPTION POWER AUDIO OFF WARNING AUTO OFF START UP PC OP code - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 42
(1Eh) (long) *1step: 10sec. Remarks Read Only Read Only Momentary It can be used by turning OFF SETTING LOCK using SETTING LOCK command. COMPUTE MODULE SERVICE MENU WD T (42/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 43
P404/ P484/ P554/ V404/ V484/ V554/ V404-T/ V484-T/ V554-T *2 Not available on P404/ P484/ P554/ V404/ V484/ V554/ V404-T/ V484-T/ V554-T Remarks This operation requires supported option TV tuner. Same as 'SURROUND' Momentary This operation requires - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 44
2) SPECTRAVIEW ENGINE Setting = ON Item PIC.MODE OP code page 02h PRESET 10h PICTURE LUMINANCE 02h BLACK 10h GAMMA 02h CUSTOM VALUE 02h WHITE 00h 00h WHITE x 10h WHITE y 10h RED x 10h RED y 10h GREEN x 10h OP code 1Ah 51h B3h 54h 68h E8h 54h 14h 52h 53h 55h 56h 57h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 45
Item GREEN y BLUE x BLUE y COLOR VISION EMU UNIFORMITY METAMERISM OP code page 10h 10h 10h 10h 02h 10h OP code 58h 59h 5Ah 5Bh FFh 5Ch Parameter 500(01F4h): 0.500 | 900(0384h): 0.900 0: 0.000 | 250(00FAh): 0.250 0: 0.000 | 150(0096h): 0.150 0: No mean 1: OFF 2: P 3: D 4: T 5: GRAY 0: OFF | 5 0: - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 46
7. Power control procedure 7.1 Power status read 1) The controller requests the monitor to reply a current power status. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'6' Message STX-'0'-'1'-'D'-'6'-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 47
Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (47/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 48
7.2 Power control 1) The controller requests the monitor to control monitor power. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'C' Message STX-'C'-'2'-'0'-'3'-'D'-'6''0'-'0'-'0'-'1'-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 49
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (49/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 50
8. Asset Data read and write Target displays have the area for to store user's asset data of up to 64bytes. 8.1 Asset Data Read Request and reply This command is used in order to read Asset Data. 1) The controller requests the monitor to reply with Asset data. Header SOH-'0'-Monitor ID - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 51
8.2 Asset Data write This command is used in order to write Asset Data. 1) The controller requests the monitor to write Asset data. Header Message SOH-'0'-Monitor ID'0'-'A'-N-N STX-'C'-'0'-'0'-'E'-'0'-'0'Data(0)-Data(1)---Data(N)-ETX Check code BCC Delimiter CR Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 52
Delimiter CR (0Dh): End of packet (52/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 53
9. Date & Time read and write 9.1 Date & Time Read This command is used in order to read the setting of Date & Time. 1) The controller requests the monitor to reply with the Date & Time. Header Message Check Delimiter code SOH-'0'-Monitor ID- STX-'C'-'2'-'1'-'1'-ETX BCC CR '0'-'A'-'0'-'6' - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 54
'1'-'F'(31h, 46h): 31(=1Fh) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday HH: Hours '0'-'0'(30h, 30h): 0 | '1'-'7'(31h, 37h): 23 (=17h) MN: - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 55
9.2 Date & Time Write This command is used in order to write the setting of the Date & Time. 1) The controller requests the monitor to write Date & Time. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'2' Message STX-'C'-'2'-'1'-'2'YY-MM-DD-WW-HH-MN-DS-ETX Check code BCC Delimiter CR Header SOH (01h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 56
Delimiter CR (0Dh): End of packet 2) The monitor replies a data for confirmation. Header Message SOH-'0'-'0'-Monitor ID'B'-'1'-'6' STX-'C'-'3'-'1'-'2'-STYY-MM-DD-WW-HH-MN-DS-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 57
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (57/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 58
10. Schedule read and write 10.1 Schedule Read This command is used in order to read the setting of the Schedule. 1) The controller requests the monitor to read Schedule. Header Message SOH-'0'-Monitor ID'0'-'A'-'0'-'8' STX-'C'-'2'-'3'-'D'-PG-ETX Check code BCC Delimiter CR Header SOH (01h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 59
'1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Delete hour MIN: Time (minute) '0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): Delete minute INPUT: Input terminal '0'-'0'(30h,30h): No mean (works on last memory) '0'-'1'(30h,31h): VGA(RGB) *1 '0'-'3'(30h,33h): DVI *1 '0'-'5'(30h,35h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 60
'0'-'0'(30h, 30h): 2000 | '6'-'3'(36h, 33h): 2099 '6'-'4'(36h, 34h): Delete year (60/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 61
MONTH: Date (month) '0'-'1'(30h, 31h): January | '0'-'C'(30h, 43h): December '0'-'D'(30h, 44h): Delete month DAY: Date (day) '0'-'1'(30h, 31h): 1 | '1'-'F'(31h, 46h): 31 '2'-'0'(32h, 30h): Delete day EXT1: Extension1 '0'-'0'(30h,30h): (On this monitor, it is always '00') EXT2: Extension 2 '0'-'0'( - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 62
10.2 Schedule Write This command is used in order to write the setting of the Schedule. 1) The controller requests the monitor to write Schedule. Header SOH-'0'-Monitor ID'0'-'A'-'2'-'2' Message STX-'C'-'2'-'3'-'E'-PG-EVENT-HOUR-MININPUT-WEEK-TYPE-PMODE-YEAR-MONTH-DAYEXT1-EXT2-EXT3-ETX Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 63
bit 5: SATURDAY bit 6: SUNDAY EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY TYPE: Schedule type bit 7: Fixed 0 bit 6: 1: Date bit 5: 1: Holiday bit 4: 1: Weekend bit 3: 1: Weekday bit 2: 0: - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 64
Delimiter CR (0Dh): End of packet (64/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 65
2) The monitor replies a data for confirmation. Header Message SOH-'0'-'0'-Monitor ID'B'-'2'-'4' STX-'C'-'3'-'3'-'E'-ST-PG-EVENT-HOUR-MININPUT-WEEK-TYPE-PMODE-YEAR-MONTH-DAYEXT1-EXT2-EXT3-ETX Check code BCC Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 66
bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY TYPE: Schedule type bit 7: Fixed 0 bit 6: 1: Date bit 5: 1: Holiday bit 4: 1: Weekend bit 3: 1: Weekday - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 67
CR (0Dh): End of packet (67/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 68
3) The controller requests the monitor to write Enable/Disable Schedule. Header Message Check code SOH-'0'-Monitor ID- STX-'C'-'2'-'3'-'F'-PG-EN-ETX BCC '0'-'A'-'0'-'A' Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 69
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (69/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 70
11. Holiday read and write 11.1 Holiday Read This command is used in order to read the setting of Holiday. 1) The controller requests the monitor to reply with the Date & Time. Header Message Check code SOH-'0'-Monitor ID- STX-'C'-'A'-'1'-'9'-'0'-'0'- BCC '0'-'A'-'0'-'A' PG-ETX Delimiter - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 71
TP: Type bit 0: End day bit 1: Day bit 2: Week bit 3: Reserved bit 4: Reserved bit 5: Reserved bit 6: Reserved bit 7: Reserved YEAR: Year '0'-'0'(30h,30h): No mean '0'-'F'(30h,46h): 2015 | '6'-'3'(36h,33h): 2099 MONTH: Month '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h): Janualy | '0'-'C'(31h,43h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 72
11.2 Holiday Write This command is used in order to write the setting of Holiday. 1) The controller requests the monitor to write Date & Time. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'2' Message STX-'C'-'A'-'1'-'9'-'0'-'1'PG-TP-YEAR-MON-DAY-EMON-EDAY-ETX Check code BCC Delimiter CR Header SOH ( - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 73
'0'-'1'(30h,31h): 1st | '1'-'F'(31h,46h): 31th EMON: End month '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h): Janualy | '0'-'C'(31h,43h): December EDAY: End day '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h): 1st | '1'-'F'(31h,46h): 31th ETX (03h): End of Message Check code BCC: Block Check Code Refer to - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 74
| '6'-'3'(36h,33h): 2099 MONTH: Month '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h): Janualy | '0'-'C'(31h,43h): December WEEK NO: Week No. '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h): 1st week '0'-'2'(30h,32h): 2nd week | '0'-'5'(30h,35h): Last week WEEK: Week '0'-'0'(30h,30h): No mean '0'-'1'(30h,31h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 75
12. Weekend read and write 12.1 Weekend Read This command is used in order to read the setting of Weekend. 1) The controller requests the monitor to reply with the Date & Time. Header Message Check code SOH-'0'-Monitor ID- STX-'C'-'A'-'1'-'A'-'0'-'0'-ETX BCC '0'-'A'-'0'-'8' Delimiter CR - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 76
Example: Weekend setting is "Saturday" and "Sunday". '2'-'0' OR '4'-'0' = '6'-'0' ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (76/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 77
12.2 Weekend Write This command is used in order to write the setting of Weekend. 1) The controller requests the monitor to write the setting of Weekend. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'A' Message STX-'C'-'A'-'1'-'A'-'0'-'1'WEEK-ETX Check code BCC Delimiter CR Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 78
'0'-'1'(30h, 31h): Error WEEK: Weekend '0'-'0'(30h, 30h): None bit assignment of a day of the week. bit0: Monday bit1: Tuesday bit2: Wednesday bit3: Thursday bit4: Friday bit5: Saturday bit6: Sunday Example: Weekend setting is "Saturday" and "Sunday". '2'-'0' OR '4'-'0' = '6'-'0' ETX (03h): End of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 79
13. Self diagnosis 13.1 Self-diagnosis status read This command is used in order to read the Self-diagnosis status. 1) The controller requests the monitor to read Self-diagnosis status. Header Message Check Delimiter code SOH-'0'-Monitor ID- STX-'B'-'1'-ETX BCC CR '0'-'A'-'0'-'4' Header - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 80
'A'-'2'(41h, 32h):A2: SENSOR reached at the temperature that the user had specified. 'B'-'0'(42h, 30h):B0: No signal 'D'-'0'(44h, 30h):D0: PROOF OF PLAY buffer reduction 'E'-'0'(45h, 30h):E0: System error ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 81
14. Serial No. & Model Name Read 14.1 Serial No. Read This command is used in order to read a serial number. 1) The controller requests the monitor to read a serial number. Header Message Check code SOH-'0'-Monitor ID- STX-'C'-'2'-'1'-'6'-ETX BCC '0'-'A'-'0'-'6' Delimiter CR Header SOH ( - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 82
Note: No null termination character is sent. ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (82/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 83
14.2 Model Name Read This command is used in order to read the Model Name. 1) The controller requests the monitor to read Model Name. Header Message Check code SOH-'0'-Monitor ID- STX-'C'-'2'-'1'-'7'-ETX BCC '0'-'A'-'0'-'6' Delimiter CR Header SOH (01h): Start of Header '0' (30h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 84
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (84/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 85
15. Security Lock 15.1 Security Lock Control This command sets the condition of security lock function to "LOCK" or "UNLOCK". If security pass codes 1st to 4th are matched with monitor resisted pass codes, then this command is executed, and reply no error status and a new condition. If codes aren't - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 86
2) The monitor replies the result to the controller. Header Message SOH-'0'-'0'-Monitor ID'B'-'0'-'A' STX-'C'-'3'-'1'-'D'ST-EN-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 87
16. Direct TV Chanel Read & Write When DTV unit (Option unit) is installed, channel settings is read and write directly. 16.1 Direct TV Chanel Read & Reply 1) The controller requests the monitor to read channel information. Header Message Check code SOH-'0'-Monitor ID'0'-'A'-'0'-'6' STX - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 88
16.2 Direct TV Chanel Write & Reply 1) The controller requests the monitor to write channel information. Header Message Check code Delimiter SOH-'0'-Monitor ID- STX-'C'-'2'-'2'-'D'- BCC CR '0'-'A'-'1'-'2' MajorCH-MinorCH-ETX Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 89
17. Daylight Saving read & write 17.1 Daylight Saving Read This command is used in order to read the setting of Daylight Saving. 1) The controller requests the monitor to reply a Daylight Saving setting. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'1'-'0'-'0'-ETX Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 90
LAST : 05h (30h, 35h) BD2: BEGIN DAY2 (Day of the week) SUNDAY : 01h (30h, 31h) MONDAY : 02h (30h, 32h) TUESDAY : 03h (30h, 33h) WEDNESDAY : 04h (30h, 34h) THURSDAY : 05h (30h, 35h) FRIDAY : 06h (30h, 36h) SATURDAY : 07h (30h, 37h) BT1: BEGIN TIME1 (Hour) 00h (30h, 30h) - 23 (32h, - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 91
17.2 Daylight Saving Write This command is used in order to write the setting of the Daylight Saving. 1) The controller requests the monitor to write Daylight Saving. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'E' Message STX-'C'-'A'-'0'-'1'-'0'-'1'-BM-BD1-BD2BT1-BT2-EM-ED1-ED2-ET1-ET2-TD-ETX Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 92
-00:30 : 02h (30h, 32h) -01:00 : 03h (30h, 33h) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet 2) The monitor replies a written in result. Header Message SOH-'0'-'0'-Monitor ID- STX - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 93
18. Firmware Version 18.1 Firmware Version Read This command is used in order to read a firmware version (FIRMWARE REVISION). 1) The controller requests the monitor to reply a firmware version. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'2'-TY-ETX Check code BCC - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 94
00h (30h, 30h) - 09h (30h, 39h) BV2: Minor (Basic) Version2: 00h (30h, 30h) - 09h (30h, 39h) BV3: Minor (Basic) Version3: 00h (30h, 30h) - 09h (30h, 39h) BR1: Branch Version1: A:41h (34h, 31h) - Z:5Ah (35h, 41h) BR2: Branch Version2: A:41h (34h, 31h) - Z:5Ah (35h, 41h) Check code BCC: Block Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 95
19. Auto ID 19.1 Auto ID Execute This command is used in order to execute Auto ID function. 1) The controller requests the monitor to execute Auto ID function. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'A'-'0'-'1'-ETX Check code Delimiter BCC CR Header SOH (01h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 96
19.2 Auto ID Complete This command is used in order to notify complete status of Auto ID. 1) The monitor sends the controller to complete status of Auto ID. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'C' Message STX-'C'-'A'-'0'-'A'-'0'-'2'-ST-MON-ETX Check code BCC Header SOH (01h): Start of Header - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 97
19.3 Auto ID Reset This command is used in order to reset Auto ID. 1) The controller requests the monitor to reset Auto ID. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'A'-'0'-'3'-ETX Check code Delimiter BCC CR Header SOH (01h): Start of Header '0' (30h): Reserved - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 98
20. Input Name 20.1 Input Name Read This command is used in order to read the setting of Input Name. 1) The controller requests the monitor to reply Input Name setting. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'4'-'0'-'0'-ETX Check code BCC Delimiter CR Header SOH ( - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 99
Step3: Byte data represents the ASCII string data. Example: 56h 47h 41h -> "VGA" Result: Input Name is "VGA". Note: No null termination character is sent. ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 100
20.2 Input Name Write This command is used in order to write the setting of Input Name. 1) The controller requests the monitor to write Input Name. Header Message SOH-'0'-Monitor ID'0'-'A'- LN(H)-LN(L) STX-'C'-'A'-'0'-'4'-'0'-1'Data(0)-Data(1)-Data(2)- --- -Data(n)-ETX Check code BCC - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 101
ST: Status 00h (30h, 30h): No Error 01h (30h, 31h): Error ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (101/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 102
20.3 Input Name Reset This command is used in order to reset the Input Name. 1) The controller requests the monitor to reset Input Name. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'4'-'0'-'2'-ETX Check code Delimiter BCC CR Header SOH (01h): Start of Header '0' (30h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 103
21. Auto Tile Matrix 21.1 Auto Tile Matrix Execute This command is used in order to activate the Auto Tile Matrix Setup. 1) The controller requests the monitor to execute Auto Tile Matrix Header SOH-'0'-Monitor ID'0'-'A'-'1'-'2' Message STX-'C'-'A'-'0'-'3'-'0'-'1'HM-VM-PID-SEL-TMEM-ETX Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 104
2) The monitor replies receipt result. Header SOH-'0'-'0'-Monitor ID'B'-'0'-'A' Message STX-'C'-'B'-'0'-'3'-'0'-'1'-ST-ETX Check code Delimiter BCC CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 105
21.2 Auto Tile Matrix Complete This command is used in order to notify complete status of Auto Tile Matrix Setup. 1) The monitor notifies that Auto Tile Matrix completed to controller. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'A' Message STX-'C'-'A'-'0'-'3'-'0'-'2'-ST-ETX Check code BCC Header - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 106
21.3 Auto Tile Matrix Monitors Read This command is used in order to read the setting of H/V Monitors. 1) The controller requests the monitor to reply H/V Monitors setting. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'3'-'0'-'4'-ETX Check code Delimiter BCC CR Header - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 107
21.4 Auto Tile Matrix Monitors Write This command is used in order to write the setting of H/V Monitors. 1) The controller requests the monitor to write H/V Monitors. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'C' Message Check code STX-'C'-'A'-'0'-'3'-'0'-'5'-HM-VM-ETX BCC Header SOH (01h): Start - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 108
21.5 Auto Tile Matrix Reset This command is used in order to deactivate the Auto Tile Matrix Setup. 1) The controller requests the monitor to reset Auto Tile Matrix Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'3'-'0'-'6'-ETX Check code Delimiter BCC CR Header SOH (01h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 109
22. Power Save Mode 22.1 Power Save Mode Read This command is used in order to read the Power Save Mode. 1) The controller requests the monitor to read Power Save Mode Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'B'-0'-'0'-ETX Check code BCC Delimiter CR Header SOH (01h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 110
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (110/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 111
22.2 Power Save Mode Write This command is used in order to write the setting of Power Save Mode. 1) The controller requests the monitor to write Power Save Mode. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'A' Message STX-'C'-'A'-'0'-'B'-'0'-'1'-MODE-ETX Check code BCC Delimiter CR Header SOH (01h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 112
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (112/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 113
22.3 Auto Power Save Time Read This command is used in order to read the setting of Auto Power Save Time. 1) The controller requests the monitor to reply Time setting. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'B'-'0'-'2'-ETX Check code BCC Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 114
22.4 Auto Power Save Time Write This command is used in order to write the setting of Auto Power Save Time. 1) The controller requests the monitor to write Time. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'A' Message Check code STX-'C'-'A'-'0'-'B'-'0'-'3'-TIME-ETX BCC Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 115
22.5 Auto Standby Time Read This command is used in order to read the setting of Auto Standby Time. 1) The controller requests the monitor to reply Time setting. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'B'-'0'-'4'-ETX Check code BCC Delimiter CR Header SOH (01h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 116
22.6 Auto Standby Time Write This command is used in order to write the setting of Auto Standby Time. 1) The controller requests the monitor to write Time. Header SOH-'0'-Monitor ID-'0''A'-'0'-'A' Message Check code STX-'C'-'A'-'0'-'B'-'0'-'5'-TIME-ETX BCC Header SOH (01h): Start of Header - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 117
23. Setting Copy 23.1 Setting Copy Read This command is used in order to read the Setting Copy. 1) The controller requests the monitor to read Setting Copy Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'9'-'0'-'0'-ETX Check code BCC Delimiter CR Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 118
Bit6: OSD Bit7: MULTI DISP Bit8: PROTECT Bit9: EXT-CTRL Bit10: ADVANCED Bit11: ADVANCED2 Bit12: HTTP Bit13: Reserve Bit14: Reserve Bit15: Reserve Ex.) Setting the following value for T4 Bit0: ALL INPUT is OFF (0). Bit1: PICTURE is OFF (0). Bit2: ADJUST is ON (1). Bit3: AUDIO is ON (1). Step 1: Put - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 119
23.2 Setting Copy Write This command is used in order to write the setting of Setting Copy. 1) The controller requests the monitor to write Setting Copy. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'0' Message Check code STX-'C'-'A'-'0'-'9'-'0'-'1'- BCC T4-T3-T2-T1-ETX Delimiter CR Header SOH (01h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 120
2) The monitor replies a written in result. Header Message SOH-'0'-'0'-Monitor ID- STX-'C'-'B'-'0'-'9'-'0'-'1'-ST-ETX 'B'-'0'-'A' Check code Delimiter BCC CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 121
23.3 Setting Copy Start This command is used in order to start Setting Copy. 1) The controller requests the monitor to write Setting Copy Start. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message Check code STX-'C'-'A'-'0'-'9'-'0'-'2'-ETX BCC Delimiter CR Header SOH (01h): Start of Header '0' - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 122
24. Security Enable 24.1 Security Enable Read This command is used in order to read the Security Enable. 1) The controller requests the monitor to read Security Enable Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'0'-'C'-'0'-'2'-ETX Check code BCC Delimiter CR Header SOH (01h - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 123
24.2 Security Enable Write This command is used in order to write the setting of Security Enable. 1) The controller requests the monitor to set Security password. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'C' Message STX-'C'-'A'-'0'-'C'-'0'-'1'ENA-'0'-'0'-PWD1-...-PWD16-ETX Check code BCC Delimiter - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 124
SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID. Ex.) When this byte is set to 'A', replying monitor's ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte) Message STX - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 125
25. LAN MAC Address 25.1 LAN MAC Address Read This command is used in order to read the MAC Address. 1) The controller requests the monitor to read MAC Address Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'2'-'2'-'A'-'0'-'2'-ETX Check code Delimiter BCC CR Header SOH (01h) : - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 126
BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (126/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 127
26. Proof of Play 26.1 Set Proof of Play Operation Mode This command is used in order to set Operation mode of Proof of Play. 1) The controller requests the monitor to set Operation mode of Proof of Play. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'A' Message STX-'C'-'A'-'1'-'5'-'0'-'0'-MDETX Check - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 128
'0'-'2'(30h, 32h): Already Start/Stop/Clear ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (128/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 129
26.2 Get Proof of Play Current This command is used in order to get Current log data of Proof of Play. Note：Proof of Play information cannot be read from the display when it is in OFF state. The display must be fully powered on to read Proof of Play information. Also the display does not continue to - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 130
CNH: Current log data Number (High byte) CNL: Current log data Number (Low byte) '0','0','0','1' -'F','F','F','F' (30h, 30h, 30h, 31h - 46h, 46h, 46h, 46h) :1 - 65535 Data(0)-Data(18): Data of Proof of Play Log Data of Proof of Play : Data(0)-Data(18) Data(0): Check INPUT PITURE ※Same as VCP(Page11 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 131
'3'-'0'(33h,30h): Contents Copy Success '3'-'1'(33h,31h): Contents Copy Error (No media) '3'-'2'(33h,32h): Contents Copy Error (Connect error) '3'-'3'(33h,33h): Contents Copy Error (Out of disk space) '3'-'4'(33h,34h): Contents Copy Error (Read/Write error) '3'-'5'(32h,35h) - '3'-'F'(33h,46h): - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 132
26.3 Get Proof of Play Status This command is used in order to get Proof of Play Status. 1) The controller requests the monitor to get status of Proof of Play. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message STX-'C'-'A'-'1'-'5'-'0'-'2'-ETX Check code BCC Delimiter CR Header SOH (01h) : Start - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 133
ST4: Maximum Number-High byte (Maximum possible number of log data items) ST5: Maximum Number-Low byte (Maximum possible number of log data items) '0','0','0','0' - 'F','F','F','F' (30h,30h,30h,30h - 46h,46h,46h,46h): 0 - 65535 ST6: Current Proof of Play status. Stop: 00h (30h, 30h) Start: 01h (30h, - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 134
26.4 Get Proof of Play Number to Number This command is used in order to get Proof of Play number to number log. 1) The controller requests the monitor to get Number to Number log of Proof of Play. Header SOH-'0'-Monitor ID'0'-'A'-'1'-'0' Message STX-'C'-'A'-'1'-'5'-'0'-'3'BNS(H)- BNS(L)-BNE(H)- - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 135
Header SOH (01h) : Start of Header '0' (30h) : Reserved Monitor ID: Specify the Monitor ID from which you want to get status. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h) : Message sender is the controller. 'A' (41h) : Message Type is "Command". '3'-'4' (33h, 36h) : Message length is 38 bytes. - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 136
the controller. 'A' (41h): Message type is "Command". '1'-'0'(31h, 30h): Message length Message STX (02h): Start of Message 'C'-'A'-'1'-'B' (43h, 41h, 31h, 42h): Service Lock Control command EN: Enable /Disable '0'-'0'(30h, 30h): OFF '0'-'1'(30h, 31h): ON P1-P2-P3-P4: Lock condition control data P1 - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 137
2) The monitor replies the result to the controller. Header SOH-'0'-'0'-Monitor ID'B'-'0'-'A' Message STX-'C'-'B'-'1'-'B'-ST-EN-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 138
28. Emergency Contents This function which plays files in the EMRGENCY CONTENTS folder in the root folder on SD card automatically using MEDIA PLAYER function. During playing, a display prohibits operation except power off. Create "EMERGENCY CONTENTS" folder in a route folder. "Display command" - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 139
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet (139/139) - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 140
28.2 Emergency Contents Delete This command is used in order to stop Emergency Contents. 1) The controller requests the monitor to set Security password. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'8' Message Check code Delimiter STX-'C'-'A'-'1'-'F'-'0'-'0'-ETX BCC CR Header SOH (01h): Start of - Sharp UN552VS/UN552VS-TMX4P | External Control Codes for the - Page 141
All data are subject to change without notice. (March 2, 2018) Copyright 2004-2018 NEC Display Solutions, Ltd. All Right Reserved This document provides the technical information for users. NEC Display Solutions, Ltd. reserves the right to change or modify the information contained herein without
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
 |
 |
(1/139)
External Control
NEC LCD Monitor
Rev.1.3 (G4)
INDEX
I. Application
.............................................................................................................................................
4
II. Preparation
...........................................................................................................................................
4
2. Connectors and wiring
.........................................................................................................................
4
2.1 RS-232C Remote control
....................................................................................................................
4
2.2 LAN control
.........................................................................................................................................
5
III. Communication specification
............................................................................................................
6
3. Communication Parameter
..................................................................................................................
6
3.1 RS-232C Remote control
....................................................................................................................
6
3.2 LAN control
.........................................................................................................................................
6
3.3 Communication timing
.......................................................................................................................
6
4. Communication Format
........................................................................................................................
7
4.1 Header block format (fixed length)
...................................................................................................
8
4.2 Message block format
......................................................................................................................
10
4.3 Check code
.......................................................................................................................................
12
4.4 Delimiter
...........................................................................................................................................
13
5. Message type
......................................................................................................................................
14
5.1 Get current Parameter from a monitor.
..........................................................................................
14
5.2 "Get parameter" reply
......................................................................................................................
15
5.3 Set parameter
...................................................................................................................................
17
5.4 "Set parameter" reply
......................................................................................................................
18
5.5 Commands
........................................................................................................................................
19
IV. Control Commands
...........................................................................................................................
22
6. Typical procedure example
...............................................................................................................
22
6.1. How to change the “Backlight” setting.
........................................................................................
22
6.2. How to read the measurement value of the built-in temperature sensors
..................................
25
6.3. Operation Code (OP code) Table
....................................................................................................
28
7. Power control procedure
...................................................................................................................
46
7.1 Power status read
............................................................................................................................
46
7.2 Power control
...................................................................................................................................
48
8. Asset Data read and write
.................................................................................................................
50
8.1 Asset Data Read Request and reply
................................................................................................
50
8.2 Asset Data write
...............................................................................................................................
51
9. Date & Time read and write
...............................................................................................................
53
9.1 Date & Time Read
............................................................................................................................
53