Sharp XE-A42S XE-A42S Operation Manual in English and Spanish - Page 72

In Case of SD Error - memory card

Get Sharp XE-A42S PDF manuals and user guides View all Sharp XE-A42S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

2 In Case of SD Error If an error occurs while data is transferred from your cash register to the inserted SD memory card and vice l versa, it will be indicated by a corresponding error message shown on the operator display. Press the key to clear the error, then take the corresponding action. SD error message table Display (Error message) Error status and action NO CARD No SD memory card is found. Insert an SD memory card into the SD card slot or reinsert it correctly. CARD PROTECT The write-protect switch on the SD memory card is in the "PROTECTED" position. Set the switch on the "NOT PROTECTED" position. CARD FULL The SD memory card is full. Delete unwanted data from the card on a PC or replace the card with a new one. When using a new SD memory card, be sure to format it in advance. ACCESS ERROR The SD memory card has no desired data. Replace it with another SD memory card containing the desired data. FILE FAILED The data stored in the SD memory card is incorrect. Write correct data into the SD memory card on a PC. OVER LIMIT. The maximum allowable number of times of sales data writing is exceeded. Delete unwanted data from the SD memory card on a PC or replace the card with a new one. When using a new SD memory card, be sure to format it in advance. POWER OFF A power failure has occurred while the SD memory card is accessed. Perform the interrupted operation again from the beginning after power recovery. SD CANCEL The data transfer operation has been canceled. Perform the same operation again from the beginning. SD ERROR An error other than the above mentioned has occurred while the SD memory card is accessed. Perform the interrupted operation again from the beginning. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
70
If an error occurs while data is transferred from your cash register to the inserted SD memory card and vice
versa, it will be indicated by a corresponding error message shown on the operator display. Press the
l
key to
clear the error, then take the corresponding action.
SD error message table
In Case of SD Error
2
Display
Error status and action
(Error message)
NO CARD
No SD memory card is found. Insert an SD memory card into the SD card slot or reinsert it correctly.
CARD PROTECT
The write-protect switch on the SD memory card is in the “PROTECTED” position. Set the switch on
the “NOT PROTECTED” position.
CARD FULL
The SD memory card is full. Delete unwanted data from the card on a PC or replace the card with a
new one. When using a new SD memory card, be sure to format it in advance.
ACCESS ERROR
The SD memory card has no desired data. Replace it with another SD memory card containing the
desired data.
FILE FAILED
The data stored in the SD memory card is incorrect. Write correct data into the SD memory card on a
PC.
OVER LIMIT.
The maximum allowable number of times of sales data writing is exceeded. Delete unwanted data
from the SD memory card on a PC or replace the card with a new one. When using a new SD memory
card, be sure to format it in advance.
POWER OFF
A power failure has occurred while the SD memory card is accessed. Perform the interrupted
operation again from the beginning after power recovery.
SD CANCEL
The data transfer operation has been canceled. Perform the same operation again from the beginning.
SD ERROR
An error other than the above mentioned has occurred while the SD memory card is accessed.
Perform the interrupted operation again from the beginning.