Sharp XR-30S Operation Manual

Sharp XR-30S - SVGA DLP Projector Manual

Get Sharp XR-30S - SVGA DLP Projector PDF manuals and user guides
UPC - 074000365216
View all Sharp XR-30S manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp XR-30S manual content summary:

  • Sharp XR-30S | Operation Manual - Page 1
    MULTIMEDIA PROJECTOR MODEL XR-40X XR-30X XR-30S OPERATION MANUAL Introduction Quick Start Setup Connections Basic Operation Useful Features Appendix
  • Sharp XR-30S | Operation Manual - Page 2
    please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10. Model No.: Serial No.: ii
  • Sharp XR-30S | Operation Manual - Page 3
    -rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same . To fit an appropriate plug to the mains lead, follow the instructions below: WARNING: THIS APPARATUS MUST BE EARTHED. IMPORTANT: The wires
  • Sharp XR-30S | Operation Manual - Page 4
    , German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederl
  • Sharp XR-30S | Operation Manual - Page 5
    operation manual carefully. Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service
  • Sharp XR-30S | Operation Manual - Page 6
    manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will Lamp Replacement See "Replacing the Lamp" on page 50. This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR40X/XR-30X) / 480,000 (XR-30S
  • Sharp XR-30S | Operation Manual - Page 7
    . • In this operation manual, the illustration and the Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset PRJ - ADJ Standard 0 projector. Note .........Indicates additional information for setting up and operating the projector. For Future Reference Maintenance P. 47 Troubleshooting
  • Sharp XR-30S | Operation Manual - Page 8
    Setup Guide 26 Adjusting the Projected Image 26 Correcting Trapezoidal Distortion ........ 28 Switching the Input Mode 29 Adjusting the Volume 29 Displaying the Black Screen and Turning off the Sound Temporarily .... 29 Resize Mode 30 Useful Features Operating with the Remote Control .... 32
  • Sharp XR-30S | Operation Manual - Page 9
    Lamp 50 Lamp 50 Caution Concerning the Lamp 50 Replacing the Lamp 50 Removing and Installing the Lamp Unit 51 Resetting the Lamp Timer 52 Connecting Pin Assignments 53 RS-232C Specifications and Command Settings 55 Computer Compatibility Chart 60 Troubleshooting 61 For SHARP Assistance
  • Sharp XR-30S | Operation Manual - Page 10
    servicing. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety and operating instructions to overturn. 10. Ventilation Slots with a grounding terminal. This plug will only fit into a grounding type power
  • Sharp XR-30S | Operation Manual - Page 11
    If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the
  • Sharp XR-30S | Operation Manual - Page 12
    of glass par- ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See "Replacing the Lamp" on page 50. Caution concerning the setup of the projector ■ For minimal servicing and to maintain high image quality
  • Sharp XR-30S | Operation Manual - Page 13
    starts to overheat due to setup problems or blockage of the air vents, " " and " " will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warn- ing indicator on the projector will blink, and after a 60-second
  • Sharp XR-30S | Operation Manual - Page 14
    country. • Operation manual (this manual and CD-ROM ) Note • Codes in "< >" are Replacement parts codes. Optional accessories ■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m)) ■ DIN-D-sub RS-232C adaptor (5 57/64" (15cm)) ■ Remote receiver ■ Lamp unit ■ Ceiling-mount
  • Sharp XR-30S | Operation Manual - Page 15
    the projector into standby mode. ENTER button For setting 37 items selected or adjusted on the menu. KEYSTONE 28 button For entering the Keystone Correction mode. Front View Zoom ring 26 For enlarging/ reducing the picture. Remote control 15 sensor Exhaust vent 47 25, 48 Lamp indicator
  • Sharp XR-30S | Operation Manual - Page 16
    Numbers in Z refer to the main pages in this operation manual where the topic is explained. Rear View Terminals AUDIO 1 Terminal for controlling the projector using a computer. 34 USB terminal Terminal connecting with the USB terminal on the computer for using the supplied remote control as the
  • Sharp XR-30S | Operation Manual - Page 17
    projector the cooling fan and extending the lamp life. 25 ON button For turning the power on. 33 FREEZE USB connection (using a USB cable or the optional remote receiver). • For returning to the previous menu screen and setting screens, and help screen. 30 RESIZE button For switching the picture size
  • Sharp XR-30S | Operation Manual - Page 18
    . • The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries. • Remove the batteries from the remote control if you will not be using the remote control for a long time. • Comply with
  • Sharp XR-30S | Operation Manual - Page 19
    using the remote control • Ensure that you do not drop it or expose it to moisture or high temperature. • The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp. 30° 23n (7 m) Remote control Remote control signal transmitters
  • Sharp XR-30S | Operation Manual - Page 20
    screen _P. 18 2. Connect the projector to the computer and plug the power cord into the AC socket of the projector When connecting equipment other than a computer, see pages 22 and 23. _PP. 21, 24 3. Remove the lens cap and turn the projector on On the projector On the remote control _P. 25 16
  • Sharp XR-30S | Operation Manual - Page 21
    768 D DVI-D Video • When you press INPUT on the projector, the INPUT list appears. Press '/" to switch the INPUT mode. _P. 29 7. Turn the computer on 8. Turn the power off Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation
  • Sharp XR-30S | Operation Manual - Page 22
    page 20 for additional information concerning "Screen Size and Projection Distance". Ceiling-mount Setup ■ It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service
  • Sharp XR-30S | Operation Manual - Page 23
    Projection (PRJ) Mode The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can
  • Sharp XR-30S | Operation Manual - Page 24
    (102 cm) 89 cm (35Љ) 311 cm (123Љ) 10.2 m (33Ј 6Љ) 11.8 m (38Ј 8Љ) 280 cm (110Љ) 9.2 m (30Ј 1Љ) 10.6 m (34Ј 9Љ) 249 cm (98Љ) 8.2 m (26Ј 9Љ) 9.4 m (30Ј 11Љ) 187 cm (74Љ) 6.1 m (20Ј 1Љ) 7.1 m (23Ј 2Љ) 166 cm (65Љ) 5.4 m (17Ј 10Љ) 6.3 m (20Ј 7Љ) 132 cm (52Љ) 4.3 m (14Ј 2Љ) 5.0 m (16Ј 5Љ) 125 cm
  • Sharp XR-30S | Operation Manual - Page 25
    the projector before you turn on the connected equipment. • For more details of connection and cables, refer to the operation manual of keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer's operation manual to enable your computer's
  • Sharp XR-30S | Operation Manual - Page 26
    provided by the video equipment manufacturer. • When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a commercially available cable that fits in the projector terminal you want to connect. • The projector does not support RGBC signals via the Euro-scart. 22
  • Sharp XR-30S | Operation Manual - Page 27
    available terminal as Sharp service part QCNWGA038WJPZ) Terminal on the projector AUDIO 1 service part QCNWGA038WJPZ) AUDIO OUT RCA audio input terminal ø3.5 mm stereo minijack to RCA audio cable (commercially available) Note • When using the ø3.5 mm mono audio cable, the volume level will
  • Sharp XR-30S | Operation Manual - Page 28
    . Refer to the operation manual of the computer for details. • See pages 53 and 54 for connection of an RS-232C serial control cable. Info • Do the computer. This may damage your computer or projector. • Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is
  • Sharp XR-30S | Operation Manual - Page 29
    on the remote control. • The power indicator illuminates green. • After the lamp indicator illuminates, the projec- tor is ready to start operation. Info • When "Auto Restart" is set to "On": If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on
  • Sharp XR-30S | Operation Manual - Page 30
    Image Projection Setup Guide screen About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note • The Setup Guide screen automatically high-
  • Sharp XR-30S | Operation Manual - Page 31
    can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. 2 Remove your hands from
  • Sharp XR-30S | Operation Manual - Page 32
    20 degrees (when the resize mode is set to "NORMAL" (see page 30)). 1 Press KEYSTONE to enter the Keystone Correction mode. • You can also display the on-screen display of the Keystone Correction mode with KEYSTONE on the projector mode will disappear. • You can also use KEYSTONE on the projector.
  • Sharp XR-30S | Operation Manual - Page 33
    on the remote control to select the input mode. • When you press INPUT on the projector or DVI on the remote control, the INPUT Turning off the Sound Temporarily Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound. Note • Pressing AV MUTE again will turn
  • Sharp XR-30S | Operation Manual - Page 34
    1400 K 1050) SXGA (1280 K 1024) WXGA (1280 K 768) NORMAL XR-40X/30X XR-30S BORDER XR-40X/30X XR-30S STRETCH XR-40X/30X XR-30S 1024 K 768 800 K 600 768 K 576 600 K 450 1024 K 576 800 K 450 J J Input Signal Computer XR-40X/30X XR-30S Image type NORMAL Output screen image BORDER STRETCH
  • Sharp XR-30S | Operation Manual - Page 35
    VIDEO • "STRETCH" is fixed when 540P, 720P, 1035I or 1080I signals are entered. Input Signal DVD / Video Image type NORMAL * Output screen image BORDER * STRETCH 4:3 aspect ratio * * 480I, 480P, 576I, Letter box 576P, NTSC, PAL, SECAM * Squeezed 16:9 image * Squeezed 4:3 image * 16:9
  • Sharp XR-30S | Operation Manual - Page 36
    +Quiet Mode Press ECO+QUIET on the remote control or on the projector to switch the Eco+Quiet mode between on and off. • When the Eco+Quiet Mode is set to "ON", the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend. Canceling the break timer
  • Sharp XR-30S | Operation Manual - Page 37
    only when RGB signal is input. Auto Sync (Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. Note • When the optimum image cannot be achieved with Auto Sync adjustment, use the help
  • Sharp XR-30S | Operation Manual - Page 38
    projector with the remote control. For details, see the operation manual of the receiver. Connecting with a USB cable Computer To USB terminal Remote receiver To USB terminal (optional, AN-MR2) or USB cable (commercially available or available as Sharp service that do not support USB. • Versions
  • Sharp XR-30S | Operation Manual - Page 39
    when selecting S-VIDEO or VIDEO. *5 Adjustment range for XR-40X/XR-30X. *6 Adjustment range for XR-30S. Resize Page 41 Image Shift -96 +96 *5 -75 +75 *6 Page 41 Keystone -168 +168 *5 -124 +124 *6 Page 41 OSD Display [On/Off] Page 42 Background Page 42 Setup Guide [On/Off] Page 42 PRJ Mode Page 42
  • Sharp XR-30S | Operation Manual - Page 40
    Menu Items (Continued) "Projector adjustment (PRJ-ADJ)" menu Picture SCR - ADJ Auto Power Off Auto Restart STANDBY Mode System Sound Speaker Audio Input RS-232C Fan Mode System Lock PRJ - ADJ On On Standard On On Audio 1 9600bps Normal Disable Help Lamp Timer(Life) 0h 0 min 100% SEL./ADJ
  • Sharp XR-30S | Operation Manual - Page 41
    Adjusting "Bright". • This operation can also be performed by using the buttons on the projector. 1 Press MENU/HELP. • The "Picture" menu screen for the selected input Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset PRJ - ADJ Standard 0 0 0 0 0 1 Bright Help SEL./ADJ. ENTER END
  • Sharp XR-30S | Operation Manual - Page 42
    Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset Standard 0 15 0 0 0 1 Bright Help 5 Press MENU/HELP. • The menu screen will disappear. SEL./ADJ. Single ADJ END Note • Menu buttons do not function while the projector is operating the "Auto Sync", "Break Timer", "FREEZE
  • Sharp XR-30S | Operation Manual - Page 43
    VIDEO input Picture SCR - ADJ Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset PRJ - ADJ Help Standard 0 0 0 0 0 in memory. Note • You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.) • *sRGB is
  • Sharp XR-30S | Operation Manual - Page 44
    For making skin tones purplish. For less sharpness. For high fidelity color reproduction. For encoded as is at 24 frames/second. The projector can convert this film source to progressive video in the chart.) The lamp life cooler, bluish, fluorescent-like images. will be approximately 3,000 hours
  • Sharp XR-30S | Operation Manual - Page 45
    Image Shift 3 Keystone 4 OSD Display 5 Background 6 Setup Guide 7 PRJ Mode 8 Language Border 0 0 On Logo 30 and 31. • You can also press RESIZE on the remote con- trol to set the resize mode. (See page 30 can be adjusted up to an angle of approximately ±20 degrees (when "Resize" is set to "Normal").
  • Sharp XR-30S | Operation Manual - Page 46
    Language Selectable items Logo Blue None Description Sharp logo screen Blue screen - 6 Selecting the Setup Guide Selectable items On Off Description Displaying the Setup Guide when turning the projector on. Not displaying the Setup Guide. The projector can switch the on-screen display language
  • Sharp XR-30S | Operation Manual - Page 47
    automatically enter standby mode. The Auto Power Off function will be disabled. 4 Setting the Confirmation Sound (System Sound) Selectable items On Off Description A confirmation sound is made when the projector turns on/off. No confirmation sound is made. Note • When the Auto Power Off function
  • Sharp XR-30S | Operation Manual - Page 48
    is turned on. We suggest you record the keycode in a safe place where only authorized users have access. Info • If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 63). Even if the product warranty is valid, the keycode reset will
  • Sharp XR-30S | Operation Manual - Page 49
    Buttons Hold down ENTER on the projector for about 5 seconds while the projector is being turned on. On-screen display • The keylock function does not affect the operation with the remote control buttons. • You cannot use the keylock function while the projector is warming up. a Taking the Keylock
  • Sharp XR-30S | Operation Manual - Page 50
    marks (✔). • The items in the "Help" menu change, de- pending on the input signal or setting that you have selected. • If the problem is not solved, refer to "Troubleshooting". (see pages 61 and 62) • When selecting "sRGB" in "Picture Mode", the item "Color is faded or poor" is not displayed. This
  • Sharp XR-30S | Operation Manual - Page 51
    diluted with water Wax Thinner Info • If you want to clean the air vents during projector operation, ensure you press STANDBY/ON on the projector or STANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, clean the vents. Appendix Mild detergent
  • Sharp XR-30S | Operation Manual - Page 52
    to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red. ■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on. Indicators on the
  • Sharp XR-30S | Operation Manual - Page 53
    indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • The cooling fan keeps the internal temperature of the projector constant and this function is controlled
  • Sharp XR-30S | Operation Manual - Page 54
    the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center. * If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center
  • Sharp XR-30S | Operation Manual - Page 55
    on the remote control to put the projector into standby mode. • Wait until the cooling fan stops. 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). STANDBY/ON button AC socket User service screw (for lamp unit
  • Sharp XR-30S | Operation Manual - Page 56
    user service screw (3) to secure the lamp unit cover. Info • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Securing screws Resetting the Lamp Timer Reset the lamp timer after replacing the lamp
  • Sharp XR-30S | Operation Manual - Page 57
    Earth (green/sync on green) 8. Earth (blue) 1 6 5 10 9. Not connected 10. GND 11. Not connected 12. Bi-directional data 13. Horizontal sync signal T.M.D.S data 0- 18. T.M.D.S data 0+ 19. T.M.D.S data 0 shield 20. Not connected 21. Not connected 22. T.M.D.S clock shield 23. T.M.D.S clock
  • Sharp XR-30S | Operation Manual - Page 58
    CD 2. RD 3. SD 4. ER 5. SG 6. DR 7. RS 8. CS 9. CI Note • Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Projector Pin No. 4 5 6 Computer Pin No. 4 5 6 USB Terminal: Type B USB connector 43 Pin
  • Sharp XR-30S | Operation Manual - Page 59
    Normal response Parameter 4-digit Problem response (communication error or incorrect command) O K Return code (0DH) E R R Return code (0DH) Info • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then
  • Sharp XR-30S | Operation Manual - Page 60
    0 - 9999(Integer) T L T M _ _ _ 1 0, 15, 30, 45 T L T L _ _ _ 1 0% - 100%(Integer) T N A M _ _ _ 1 XR40X / XR30X / XR30S M N R D _ _ _ 1 XR-40X / XR-30X / XR-30S P J N 1 * * * * OK or ERR P J N 2 * * * * OK or ERR P J N 3 * * * * OK or ERR P J N 0 _ _ _ 1 Projector Name I R G B _ _ _ 1 OK or ERR
  • Sharp XR-30S | Operation Manual - Page 61
    CONTROL CONTENTS COMMAND PARAMETER Power ON Resize ALL Reset 30 - +30 R A B R _ * * * OK or ERR Red -30 - +30 R A R D _ * * * OK or ERR Blue -30 - +30 R A B E _ * * * OK or ERR Color -30 - +30 R A C O _ * * * OK or ERR Tint -30 - +30 R A T I _ * * * OK or ERR Sharp -30 - +30
  • Sharp XR-30S | Operation Manual - Page 62
    Game V A P S _ _ 1 3 OK or ERR Contrast -30 - +30 V A P I _ * * * OK or ERR Bright -30 - +30 V A B R _ * * * OK or ERR Color -30 - +30 V A C O _ * * * OK or ERR Tint -30 - +30 V A T I _ * * * OK or ERR Sharp -30 - +30 V A S H _ * * * OK or ERR CLR Temp -2 - +2 V A C T _ _ * * OK
  • Sharp XR-30S | Operation Manual - Page 63
    Guide On Off System Sound On Off Internal Speaker On Off RGB Frequency Horizontal Check Vertical Fan Mode Normal High Lamp D _ _ _ 1 OK or ERR L P R E 0 0 0 1 ERR RETURN Standby mode (or 30-second startup time) ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR
  • Sharp XR-30S | Operation Manual - Page 64
    75 75 VESA Standard ✔ ✔ ✔ ✔ DVI-D Support ✔ ✔ ✔ ✔ Display XR-40X/ XR-30X XR-30S Upscale Upscale True True Intelligent Compression Intelligent Compression Upscale Upscale True Intelligent Intelligent Compression Compression Note • When this projector receives 640K350 VESA format VGA signals
  • Sharp XR-30S | Operation Manual - Page 65
    . • Remote control battery has run out. • External output has not been set when connecting notebook computer. • The lamp unit cover is not installed correctly. • If the connected DVI digital equipment is turned on before the "DVI-D" input mode is selected on the projector, the image may not be
  • Sharp XR-30S | Operation Manual - Page 66
    • The lamp will eventually need to be changed. time to turn on. While the remaining lamp life draws to a close, replace the lamp. Picture is dark. The remote control cannot be used. • Operate the remote control while pointing it at the projector's remote control sensor. • The remote control may
  • Sharp XR-30S | Operation Manual - Page 67
    If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on pages 61 and 62. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888
  • Sharp XR-30S | Operation Manual - Page 68
    lamp Rated voltage Rated frequency Input current Power consumption (Standby) Operation temperature Cabinet Dimensions (main body only) Weight (approx.) XR-40X/XR-30X/XR-30S 0.55" DLP® Chip XR-40X/XR-30X XGA (1024 × 768) XR-30S SVGA (800 × 600) F 2.5 - 2.6 Manual, ×1.15 (f = 20
  • Sharp XR-30S | Operation Manual - Page 69
    Dimensions Units: inches (mm) 1/4 (6) 10 7/16 (265) 1 31/64 2 5/8 (66.35) (37.65) 3 33/64 (89) 2 61/64 (75) 10 41/64 (270) 2 3/8 (60) M4 M4 M4 M4 13/32 (10) 13/32 (10) 2 61/64 (75) 1 27/64 (36) 1 3/16 (30) 1 15/16 (49) 4 7/64 (104) 65 Appendix
  • Sharp XR-30S | Operation Manual - Page 70
    34, 37 Rear adjustment foot 27 Red 40 Remote control 13 Remote control sensor 15 Replacing the lamp 50, 51 Resize 30, 41 RESIZE button 30 RGB cable 21 RS-232C terminal 24 SCR - ADJ 41 Screen Size and Projection Distance 20 Setup Guide 26, 42 Sharp 40 Speaker 43 SPOT button 32 STANDBY
  • Sharp XR-30S | Operation Manual - Page 71
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
MULTIMEDIA PROJECTOR
MODEL
XR-40X
XR-30X
XR-30S
OPERATION MANUAL
Introduction
Quick Start
Setup
Connections
Basic
Operation
Useful
Features
Appendix