Singer 7470 Confidence Instruction Manual - Page 26

Adjusting Top Thread Tension, Changing Presser Foot

Page 26 highlights

ADJUSTING TOP THREAD TENSION 90% of your sewing will be done with the word "AUTO" displayed on the tension control dial on top of the machine. Helpful Hint: A slight adjustment to the + or - side of AUTO will improve sewing appearance. STRAIGHT STITCHING The good looking appearance of your stitching is largely determined by the balanced tension of both top and bobbin threads. The tension is well balanced when these two threads 'lock' in the middle of layers of the fabric you are sewing. If, when you start to sew, you find that the stitching is irregular, you will need to adjust the tension control. Make any adjustments with presser foot 'down'. A balanced tension (identical stitches both top and bottom) is usually only desireable for straight stitch sewing. ZIG ZAG and DECORATIVE SEWING For zigzag sewing and decorative stitch functions, thread tension should be less than that for straight stitch sewing. You will always obtain a nicer stitch and less puckering when the upper thread appears slightly on the bottom side of your fabric. BOBBIN TENSION The bobbin tension has been correctly set at the factory, so you do not need to adjust it. Under side Côté de dessous Reverso Well balanced Correct Bien equilibrada Top side Côté de dessus Cara Top stitch too tight Fil supérieur trop tendu Puntada superior demasiado apretada Top stitch too loose Fil supérieur trop lâche Puntada superior demasiado floja Decrease tension Diminuer la tension Disminuir tensión Increase tension Augmenter la tension Aumentar tensión CHANGING PRESSER FOOT Be sure needle is in the up position. Raise presser foot lifter. 1. Push presser foot release button to remove the foot. 2. Place the desired foot on the needle plate aligning the presser foot pin with the foot holder. 3. Lower the presser foot lifter so that the foot holder snaps on the foot. 2 26 Presser foot lifter Levier de verrouillage du pied Palanca pie prensatelas 3 1 Foot release button Touche de verrouillage du pied Boton de desprendimiento prensatelas Foot holder Support du pied Sujetador prensatelas

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94

²6
Under side
Côté de dessous
Reverso
Top side
Côté de dessus
Cara
Well balanced
Correct
Bien equilibrada
Top stitch too tight
Fil supérieur trop tendu
Puntada superior
demasiado apretada
Top stitch too loose
Fil supérieur trop lâche
Puntada superior
demasiado floja
Decrease tension
Diminuer la tension
Disminuir tensión
Increase tension
Augmenter la tension
Aumentar tensión
1
3
Foot release button
Presser foot lifter
Levier de verrouillage du pied
Palanca pie prensatelas
Foot holder
Support du pied
Sujetador prensatelas
Boton de desprendimiento
prensatelas
Touche de verrouillage du pied
ADJUSTING TOP THREAD TENSION
90% of your sewing will be done with the word “AUTO”
displayed on the tension control dial on top of the machine.
STRAIGHT STITCHING
The good looking appearance of your stitching is largely
determined by the balanced tension of both top and bobbin
threads. The tension is well balanced when these two threads
‘lock’ in the middle of layers of the fabric you are sewing.
If, when you start to sew, you find that the stitching is irregular,
you will need to adjust the tension control.
Make any adjustments with presser foot ‘down’.
A balanced tension (identical stitches both top and bottom) is
usually only desireable for straight stitch sewing.
ZIG ZAG and DECORATIVE SEWING
For zigzag sewing and decorative stitch functions, thread ten-
sion should be less than that for straight stitch sewing.
You will always obtain a nicer stitch and less puckering when
the upper thread appears slightly on the bottom side of your
fabric.
BOBBIN TENSION
The bobbin tension has been correctly set at the factory,
so you do not need to adjust it.
CHANGING PRESSER FOOT
Be sure needle is in the up position. Raise presser foot lifter.
1. Push presser foot release button to remove the foot.
2. Place the desired foot on the needle plate aligning the
presser foot pin with the foot holder.
3. Lower the presser foot lifter so that the foot holder snaps
on the foot.
2
Helpful Hint:
A slight adjustment to the + or - side of
AUTO will improve sewing appearance.