Singer 9970 Instruction Manual - Page 16

Threading The Machine

Get Singer 9970 PDF manuals and user guides View all Singer 9970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

THREADING THE MACHINE A. PREPARING TO THREAD MACHINE 1. Raise the presser foot lifter. 2. Press the needle up/down button and set the needle in up position. (Keep this position until needle eye threading.) B. SETTING SPOOL OF THREAD ON SPOOL PIN 1. Pull up the left end of spool pin and set the spool of thread on spool pin so that the thread unrolls from the front of the spool. 2. Set the spool cap on spool pin as far as it will go. a: Reverse spool cap direction according to the size of spool. b. Use the small spool cap when you use cross wound thread. Leave small opening between cap and spool as illustration. C. THREADING THE UPPER THREAD 1. Hold thread in both hands and pass thread to the guide from rear opening. 2. Bring thread frontward and pass through the thread guide plate from right to left. 3. Bring thread to the left and pull thread down toward you along the slit. 4. Pull up thread. 5. To thread the take-up lever, draw thread up and bring thread back down again from right to left along the slit. 6. Pull thread downward along the slit. 7. Draw thread through thread guide from right side opening. 8. Pass through needle eye from front to back. Refer to next page for instructions on how to use needle threader. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
16
THREADING THE MACHINE
A.PREPARING TO THREAD MACHINE
1.
Raise the presser foot lifter.
2.
Press the needle up/down button and set the
needle in up position.
(Keep this position until needle eye threading.)
B.SETTING SPOOL OF THREAD ON
SPOOL PIN
1.
Pull up the left end of spool pin and set the spool
of thread on spool pin so that the thread unrolls
from the front of the spool.
2.
Set the spool cap on spool pin as far as it will go.
a: Reverse spool cap direction according to the
size of spool.
b. Use the small spool cap when you use cross
wound thread. Leave small opening between cap
and spool as illustration.
C.THREADING THE UPPER THREAD
1.
Hold thread in both hands and pass thread to the
guide from rear opening.
2.
Bring thread frontward and pass through the
thread guide plate from right to left.
3.
Bring thread to the left and pull thread down
toward you along the slit.
4.
Pull up thread.
5.
To thread the take-up lever, draw thread up and
bring thread back down again from right to left
along the slit.
6.
Pull thread downward along the slit.
7.
Draw thread through thread guide from right side
opening.
8.
Pass through needle eye from front to back.
Refer to next page for instructions on how to use
needle threader.