Smeg LSPU8643BL User manual

Smeg LSPU8643BL Manual

Get Smeg LSPU8643BL PDF manuals and user guides View all Smeg LSPU8643BL manuals
Add to My Manuals
Save this manual to your list of manuals

Smeg LSPU8643BL manual content summary:

  • Smeg LSPU8643BL | User manual - Page 1
    OF THE CONTROLS 18 4. WASHING PROGRAMS 23 5. OPERATING INSTRUCTIONS 27 6. CLEANING AND MAINTENANCE 47 7. TROUBLESHOOTING. WHAT TO DO IF 50 8. TROUBLESHOOTING 55 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need
  • Smeg LSPU8643BL | User manual - Page 2
    Warnings TRANSLATION OF THE ORIGINAL INSTRUCTIONS 1. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS  Before using the appliance, carefully read all the instructions contained in this manual.  During installation, take care not to injure yourself on the sharp edges of the appliance: wear
  • Smeg LSPU8643BL | User manual - Page 3
    The appliance must be installed and connected in accordance with the instructions provided by the manufacturer. Installation must be performed by qualified technicians with applicable regulations. The installation and repair or servicing shall be carried out by qualified and authorised technical
  • Smeg LSPU8643BL | User manual - Page 4
    is installed in a compartment above or below another equipment (e.g. gas burners, ovens, etc.), read carefully the instructions provided by the manufacturer of the equipment. If the instructions of the equipment do not contain information, contact the manufacturer of the equipment to ensure that the
  • Smeg LSPU8643BL | User manual - Page 5
    Warnings  Building-in the appliance underneath a hob is absolutely forbidden. Installing a hob on top of freestanding appliance is absolutely forbidden.  To ensure stability, install the appliance only under continuous worktop, securely fixed to adjacent cabinets. If the appliance is installed in
  • Smeg LSPU8643BL | User manual - Page 6
    to run a soak cycle). If the dishwasher fails to operate correctly, disconnect it from the electrical power supply and call the nearest technical service centre. Never attempt to repair the appliance yourself.  The dishwasher should only be used by adults. Use by children aged from eight years
  • Smeg LSPU8643BL | User manual - Page 7
    if swallowed. They contain substances capable of causing permanent damage to the mouth and throat, and even leading to suffocation. Observe all the safety instructions on the packaging of these products.  Do not drink the water residues which may be present on the dishes or appliance at the end
  • Smeg LSPU8643BL | User manual - Page 8
    and shut off the water tap. In the event of damage to the supply cord, have it replaced by the manufacturer or an authorised technical service centre.  Some components are live even with the on/off button in the off position. Before performing any maintenance work on the appliance, disconnect it
  • Smeg LSPU8643BL | User manual - Page 9
    door.  Cut the power cable,  Make the lock unusable. The manufacturer declines any liability for damage or injury caused by failure to comply with the instructions indicated above or as a result of tampering with even just one part of the appliance and the use of non-original spare parts. 9
  • Smeg LSPU8643BL | User manual - Page 10
    Warnings 2. INSTALLATION AND HOOK-UP 2.1 Technical characteristics Water supply pressure Water supply temperature Capacity Class of protection against moisture Protection against electric shock Electrical data min. 0,05 - max. 0,9 MPa (min. 0.5 - max. 9 bar) max. 140°F - 60°C 12-13 standard place
  • Smeg LSPU8643BL | User manual - Page 11
    Installation 2.2 General Information  This appliance may be placed up against walls or other furniture units.  If the appliance is installed near a heat source, fit a special insulating panel to prevent overheating and malfunction of the appliance.  To facilitate the installation procedure, the
  • Smeg LSPU8643BL | User manual - Page 12
    Installation Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance. Building-in a dishwasher underneath a hob is absolutely forbidden. Moreover, dishwashers may not be installed directly touching
  • Smeg LSPU8643BL | User manual - Page 13
    to be covered for safety reasons (risk of injury). The covers are available as an accessory and can be ordered through the Technical Assistance Service. - The top surface of the dishwashers can be removed to allow installation under a worktop. The appropriate kit should be purchased from authorised
  • Smeg LSPU8643BL | User manual - Page 14
    Installation 2.3 Water supply connection CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾" gas thread, inserting the filter A supplied with the dishwasher. Take care to screw the hose firmly into place with your hands and then complete by tightening about ¼ of a
  • Smeg LSPU8643BL | User manual - Page 15
    37/64), or alternatively, place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose. It is prevent the hose from coming loose and falling. For this purpose, the plastic support is equipped with a hole for tying it to the wall or water
  • Smeg LSPU8643BL | User manual - Page 16
    ordinances.  WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance, if
  • Smeg LSPU8643BL | User manual - Page 17
    Installation  Do not use adaptors or shunt connections in order to avoid the possibility of overheating or burning. The power cable must be replaced by the manufacturer or by an Authorized Service Centre. 17
  • Smeg LSPU8643BL | User manual - Page 18
    User instructions 3. DESCRIPTION OF THE CONTROLS 3.1 Upper panel All the dishwasher controls are grouped on the front panel. Programming and option selection are only possible with the
  • Smeg LSPU8643BL | User manual - Page 19
    User instructions 3.2 Information display The dishwasher is equipped with a practical DISPLAY which provides information on the programmed dishwasher functions. Rinse aid lack warning indicator Salt lack warning
  • Smeg LSPU8643BL | User manual - Page 20
    User instructions LIGHTING Pressing the ON/OFF button will start the dishwasher and will lit up the dishwasher pilot light. After approximately 3 second from this operation the
  • Smeg LSPU8643BL | User manual - Page 21
    User instructions Warning: during the initial phase of the wash program the spray arms cannot be heard in operation because they start turning about 5 minutes after the
  • Smeg LSPU8643BL | User manual - Page 22
    Description of the programs: The number, type and the sequence of wash programs depend on the model purchased. Refer to the instruction manual supplied together with the product. SOAK Pans and dishes awaiting completion of the load AUTO (according to the model) Normally soiled dishes including
  • Smeg LSPU8643BL | User manual - Page 23
    User instructions 4. WASHING PROGRAMS Before starting a washing program make sure that:  The water supply tap is open.  The softener container contains regenerating salt.  The correct amount of
  • Smeg LSPU8643BL | User manual - Page 24
    User instructions SPECIAL (if present) Allows you to enable additional programs when some models are equipped with the dry assist function by default on one or more cycles (check the manual supplied with the product). These models are not fitted with a button to control this function. The door
  • Smeg LSPU8643BL | User manual - Page 25
    User instructions display is reset. After the door has been closed, the dishwasher will carry out a pre-wash cycle, after which the set "cycle delay" option will
  • Smeg LSPU8643BL | User manual - Page 26
    dishwasher with a full load.  Load the dishwasher as indicated in the instructions manual. If the dishwasher is loaded incorrectly, it may lead to poor results as be carried out if strictly necessary, because it might cause problems in execution of the program. ENERGY MANAGEMENT After 5 minutes of
  • Smeg LSPU8643BL | User manual - Page 27
    User instructions 5. OPERATING INSTRUCTIONS After having installed the dishwasher, remove the basket retainers and prepare the machine for use as follows:  Regulate the water softening system;  Add regenerating salt; 
  • Smeg LSPU8643BL | User manual - Page 28
    User instructions 5.1 Adding the salt The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to
  • Smeg LSPU8643BL | User manual - Page 29
    User instructions In order for the water softening system to give fault-free service, the appliance performs a regeneration cycle of the system at regular intervals. The regeneration process consists of several stages. It starts at the end of the
  • Smeg LSPU8643BL | User manual - Page 30
    User instructions 5.2 Adding the rinse aid The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the
  • Smeg LSPU8643BL | User manual - Page 31
    User instructions Adjusting the amount of rinse aid  The dishwasher must be switched on and the door open.  Press and hold the cycle delay button until "b" appears
  • Smeg LSPU8643BL | User manual - Page 32
    User instructions 5.3 Adding the detergent  Open the detergent dispenser cover by lightly pressing the button P.  Add the detergent or tablet.  Close the cover by sliding it until
  • Smeg LSPU8643BL | User manual - Page 33
    User instructions With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser.
  • Smeg LSPU8643BL | User manual - Page 34
    User instructions WARNING!  Make sure that the dishes are securely in place so that they cannot tip over or obstruct the rotation of the spray arms during
  • Smeg LSPU8643BL | User manual - Page 35
    User instructions 5.5 Using the baskets Capacity, including serving dishes: 12 or 13 loading large items, certain models are equipped with tip-up supports for plates in 2 or 4 sections. With fixed supports With tip-up supports BOTTOM BASKET INSERTS Some models are equipped with bottom basket
  • Smeg LSPU8643BL | User manual - Page 36
    User instructions LOADING THE LOWER BASKET Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots, pans cups and glasses on two levels. In the centre section, plates and saucers can be loaded vertically into the supports provided. Loading examples: 36
  • Smeg LSPU8643BL | User manual - Page 37
    User instructions CUTLERY BASKET (on some models only) The basket is suitable for all types of cutlery, except long items that may interfere with the upper spray
  • Smeg LSPU8643BL | User manual - Page 38
    User instructions TOP CUTLERY BASKET (on some models only) The basket is designed to take cutlery, placed in the spaces provided, and long utensils, positioned lengthwise. The "
  • Smeg LSPU8643BL | User manual - Page 39
    User instructions FLEXIDUO TOP CUTLERY BASKET (on some models only) This comprises two independent sliding, pull-out tray racks for easier loading/unloading of cutlery. Various loading
  • Smeg LSPU8643BL | User manual - Page 40
    User instructions EXAMPLES OF LOADING FOR INTENSIVE DIRT 12 standard place setting If the bottom basket inserts are of the fold-down type, they should be laid
  • Smeg LSPU8643BL | User manual - Page 41
    User instructions 13 standard place setting TOP CUTLERY BASKET (on some models only) If the bottom basket inserts are of the fold-down type, they should be laid flat for easier loading. 41
  • Smeg LSPU8643BL | User manual - Page 42
    User instructions 13 standard place setting FLEXIDUO TOP CUTLERY BASKET (on some models only) If the bottom basket inserts are of the fold-down type, they should be laid flat for easier loading. 42
  • Smeg LSPU8643BL | User manual - Page 43
    User instructions UPPER BASKET EQUIPMENT (depending on the model) Cutlery tray For knives, spoons (tea and dessert) and long objects. The ends are designed to hold long
  • Smeg LSPU8643BL | User manual - Page 44
    User instructions Fold-down shelves For mugs, cups and long objects. The ends are designed to hold long stemmed glasses When not used they can be moved
  • Smeg LSPU8643BL | User manual - Page 45
    User instructions Fold-down tines These can be secured in a vertical position, resting on the bottom of the basket if unused, or placed in an intermediate position, as required. The single tine on the right is ideal for supporting long stemmed glasses. 45
  • Smeg LSPU8643BL | User manual - Page 46
    User instructions ADJUSTING THE UPPER BASKET The height of the top basket on the dishwasher model purchased. Version A: pull-out with adjustment in two positions.  Pull out both the basket guides.  Remove the stops, first releasing them as shown in the diagram.  Pull out the basket.  Fit
  • Smeg LSPU8643BL | User manual - Page 47
    User instructions 6. CLEANING AND MAINTENANCE Before carrying out any work, always unplug the appliance from the electrical supply or switch off the omnipolar circuit breaker. 6.1 General warnings
  • Smeg LSPU8643BL | User manual - Page 48
    that the spray arms turn freely. Otherwise, check that they have been installed correctly.  To remove and clean the planetarium sprayer follow the instructions provided. ORBITAL PLANETARIUM CLEANING THE FILTER UNIT If the dishwasher is used every day, we recommend that you clean it once a week
  • Smeg LSPU8643BL | User manual - Page 49
    it once a week.  It is advisable to periodically inspect the centre filter and, if necessary, to clean it.  remove the planetarium sprayer follow the instructions provided.  push the centre filter D from the underside to remove it from the micro- filter:  separate the two parts which make up the
  • Smeg LSPU8643BL | User manual - Page 50
    User instructions 7. TROUBLESHOOTING. WHAT TO DO IF... Fault The salt light does not turn hose Make sure that the siphon is not clogged or partially clogged Clean the filters as indicated in the manual Cutlery (e.g. serving spoons) in the cutlery drawer (if present), on the bottom of the basket or
  • Smeg LSPU8643BL | User manual - Page 51
    User instructions The dishwasher does not start Cutlery becomes oxidized even if washed together with other items that are subject to oxidation (pot handles, damaged knives, etc.)
  • Smeg LSPU8643BL | User manual - Page 52
    User instructions - if it has triggered (S), close the door with force (without slamming it) until it rearms; then open and close the door again Door does not
  • Smeg LSPU8643BL | User manual - Page 53
    User instructions Dishes not dry Clouding of glassware Water marks on some items or on plastic dishes Removable streaks on glasses, metal items and cutlery points Take care not to prevent the spray arms from rotating when loading the dishwasher Clean the spray arms as indicated in the manual 53
  • Smeg LSPU8643BL | User manual - Page 54
    bio/eco detergent not very effective Clean the filters as indicated in the manual Check and correct Find the suitable washing program in the program table Use Use separate products If after following the above troubleshooting instructions the problem persists, call the nearest After-Sales Centre.
  • Smeg LSPU8643BL | User manual - Page 55
    instructions 8. TROUBLESHOOTING cannot measure the precise water quantity that has been loaded. Problem on the water distribution system to the baskets. Water intake .  Alarms E1 and E11 require you to contact the technical assistance service.  Alarm E7 is displayed at the end of the cycle, which
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Contents
1
1.
IMPORTANT SAFETY INSTRUCTIONS ____________________ 2
2.
INSTALLATION AND HOOK-UP _________________________ 10
3.
DESCRIPTION OF THE CONTROLS _____________________ 18
4.
WASHING PROGRAMS________________________________ 23
5.
OPERATING INSTRUCTIONS___________________________ 27
6.
CLEANING AND MAINTENANCE ________________________ 47
7.
TROUBLESHOOTING. WHAT TO DO IF... _________________ 50
8.
TROUBLESHOOTING _________________________________ 55
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
This manual contains only the basic information required to use the
appliance. The complete manual can be obtained from
www.smeg.com/download-manuals
by entering the product code shown on the plate attached to the inner
right hand edge of the dishwasher door.
The manual can be accessed quickly via the QR code using a device
with a QR reader application.