Sony CDX-CA400 Installation/Connection Instructions
Sony CDX-CA400 - Compact Disc Changer System Manual
 |
View all Sony CDX-CA400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sony CDX-CA400 manual content summary:
- Sony CDX-CA400 | Installation/Connection Instructions - Page 1
3-238-717-11 (1) FM/AM Compact Disc Player Installation/Connections Installation/Connexions 2 A AUDIO OUT REAR B CDX-CA400 Sony Corporation © 2002 Printed in Korea 1 1 TOP 4 2 3 × 4 × 2 5 Equipment used in illustrations (not supplied) Appareils utilisés dans les illustrations (non fournis) - Sony CDX-CA400 | Installation/Connection Instructions - Page 2
CD/MD changer Fourni avec le changeur de CD/MD BUS AUDIO IN from car antenna de l'antenne de la voiture L R BUS AUDIO OUT AUDIO REAR AUDIO not use the built-in speaker wires installed in your car if instructions. Attention Manipulez précautionneusement le support 1 pour éviter de vous blesser aux - Sony CDX-CA400 | Installation/Connection Instructions - Page 3
To attach Attach part A of the front panel to part B of the unit as illustrated and push the left side into position until it clicks. Mounting the unit in a Japanese car (6) You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. Note To - Sony CDX-CA400 | Installation/Connection Instructions - Page 4
fournies avec la voiture 2 max. size 5 × 8 mm (7/32 × 11/32 in.) Dimension max. 5 × 8 mm (7/32 × 11/32 po.) Bracket Support Bracket Support Existing parts supplied with your car Pièces existantes fournies avec la voiture 2 max. size 5 × 8 mm (7/32 × 11/32 in.) Dimension max. 5 × 8 mm (7/32 × 11
-
1 -
2 -
3 -
4
 |
 |
Sony Corporation
© 2002
Printed in Korea
CDX-CA400
Cautions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the
yellow
and
red
power input leads
only after all other leads have been connected.
•
Run all ground wires to a common ground
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
•The use of optical instruments with this
product will increase eye hazard.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (
1
)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket
1
carefully to avoid injuring
your fingers.
TOP
Installation/Connections
Installation/Connexions
FM
/
AM
Compact Disc
Player
Connection example (
2
)
Notes
(
2
-A)
• Be sure to connect the ground cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Connection diagram (
3
)
1
To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground lead to it
first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
5
To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it
first.
1
TOP
4
5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Rear speaker
Haut-parleur arrière
Front speaker
Haut-parleur frontal
1
Power amplifier
Amplificateur de puissance
CD/MD changer
Changeur de CD/MD
×
4
2
×
2
3
2
B
BUS AUDIO IN
BUS CONTROL IN
A
AUDIO OUT REAR
3-238-717-
11
(1)