Home » Sony Manuals » Audio Components » Sony CMT-NE3 » Manual Viewer

Sony CMT-NE3 Operating Instructions - Page 24

Messages

Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

The sound is distorted. • Set the volume of the connected component lower. If the system still does not operate properly after performing the above measures, reset the system as follows: Use buttons on the unit for the operation. 1 Disconnect the power cord. 2 Reconnect the power cord. 3 Press ?/1 to turn on the system. 4 Press x, ?/1 and turn volume to the left at the same time. The system is reset to the factory settings. You should set the settings you made, such as the preset stations, clock, and timer. Messages One of the following messages may appear or flash in the display during operation. CD/MP3 NO DISC There is no disc in the player. NO STEP All of the programed tracks have been erased. OVER You have reached the end of the disc while pressing and holding M during playback or pause. FULL You tried to program 26 or more tracks (steps). PUSH STOP You pressed PLAY MODE during playback. Tuner COMPLETE The preset operation ended normally. Tape NO TAB You cannot record the tape because the tab has been removed from the cassette. NO TAPE There is no tape in the tape deck. Timer SET CLOCK You tried to select the timer with the clock not set. PUSH SELECT You tried to set the clock or timer during timer operation. SET TIMER You tried to select the timer when Play Timer or Rec Timer are not set. TIME NG Play Timer or Rec Timer start and end times are set to the same time. 24GB

Section	Page
Table of Contents	3
How to use this manual	4
Playable discs	4
Hooking up the system	6
1 Connect the speakers.	6
2 Connect the FM and AM antennas.	6
3 For models with a voltage selector, set VOLTAGE SELECTOR to the local power line voltage. The v...	7
4 Connect the power cord to a wall outlet.	7
Setting the clock	8
1 Press ?/1 to turn on the system.	8
2 Press CLOCK/TIMER SET.	8
3 Press ./> repeatedly to set the hour.	8
4 Press ENTER.	8
5 Press ./> repeatedly to set the minute.	8
6 Press ENTER.	8
1 Press CLOCK/TIMER SET.	8
2 Press ./> until “CLOCK” appears, then press ENTER.	8
3 Do the same procedures as step 3 to 6 above.	8
Loading a disc	9
1 Press Z PUSH OPEN/CLOSE on the unit.	9
2 Place a disc with the label side up on the CD compartment.	9
3 Press Z PUSH OPEN/CLOSE on the unit again to close the lid of the CD compartment.	9
Playing a disc	9
1 Press CD to switch the function to CD.	9
2 Press PLAY MODE in stop mode repeatedly until the mode you want appears.	9
3 Press N.	9
Playing repeatedly	10
Creating your own program	11
1 Press CD to switch the function to CD.	11
2 Press PLAY MODE in stop mode repeatedly until “PGM” appears.	11
3 Press ./> repeatedly until the desired track number appears.	11
4 Press ENTER on the remote.	11
5 To program additional tracks, repeat steps 3 and 4.	11
6 Press N.	11
Presetting radio stations	12
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	12
2 Press TUNING MODE repeatedly until “AUTO” appears in the display.	12
3 Press +/– (or TUNING +/– on the unit).	12
4 Press TUNER MEMORY.	12
5 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset number.	12
6 Press ENTER.	12
7 Repeat steps 3 through 6 to preset other stations.	12
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	12
2 Press TUNING MODE on the unit repeatedly until “AUTO” and “PRESET” disappear from the display.	12
3 Press +/– (or TUNING +/– on the unit) repeatedly to tune in the desired station.	12
4 Press TUNER MEMORY.	12
5 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset number.	12
6 Press ENTER.	12
7 Repeat steps 3 through 6 to preset other stations.	12
Listening to the radio	13
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	13
2 Press TUNING MODE repeatedly until “PRESET” appears in the display.	13
3 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset station.	13
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	13
2 Press TUNING MODE repeatedly until “AUTO” and “PRESET” disappear from the display.	13
3 Press +/– (or TUNING +/– on the unit) repeatedly to tune in the desired station.	13
Using the Radio Data System (RDS)	14
Loading a tape	15
1 Press Z PUSH OPEN on the unit.	15
2 Load a recorded/recordable tape into the cassette holder.	15
Playing a tape	15
1 Press TAPE to switch the function to TAPE.	15
2 Press N (or TAPE/N on the unit).	15
Recording your favorite CD tracks on a tape	16
1 Load a recordable tape.	16
2 Load a CD you want to record.	16
3 Press CD SYNCHRO.	16
4 Press z REC PAUSE/START.	16
Recording on a tape manually	16
1 Load a recordable tape.	16
2 Select the desired source to record.	16
3 Press z REC PAUSE/START.	16
4 Press z REC PAUSE/START, then start playing the desired source to record.	16
Adjusting the sound	17
1 Press EQ (or BASS/TREBLE on the unit) repeatedly to select “BASS” or “TREBLE”.	17
2 Press ./> (or TUNING +/– on the unit) repeatedly to adjust the level while “BASS” or “TREBLE” a...	17
Falling asleep to music	17
Waking up to music	18
1 Prepare the sound source you want to play.	18
2 Adjust the volume.	18
3 Press CLOCK/TIMER SET.	18
4 Press ./> repeatedly until “PLAY” appears, then press ENTER.	18
5 Set the time to start playing.	18
6 Set the time to stop playing following the same procedure as step 5.	18
7 Press ./> repeatedly until the desired sound source appears.	18
8 Press ENTER.	18
9 Press ?/1 to turn off the system.	18
Timer recording radio programs	19
1 Tune in the preset radio station (see “Listening to a preset station” on page13).	19
2 Press CLOCK/TIMER SET.	19
3 Press ./> repeatedly until “REC” appears, then press ENTER.	19
4 Set the time to start recording.	19
5 Set the time to stop recording following the same procedure as step 4.	19
6 Load a recordable tape.	19
7 Press ?/1 to turn off the system.	19
Turning off the display	20
Viewing information about the disc in the display	20
Hooking up optional components	21
1 Connect audio cords. See the illustration above.	21
2 Press FUNCTION repeatedly until “MD” appears. Start playing the connected component.	21
1 Connect audio cords.	21
2 Start recording manually. See “Recording on a tape manually” on page16.	21
Problems and remedies	22
1 Make sure the power cord and speaker cords are correctly and firmly connected.	22
2 Find your problem in the troubleshooting checklist below and take the indicated corrective action.	22
1 Disconnect the power cord.	24
2 Reconnect the power cord.	24
3 Press ?/1 to turn on the system.	24
4 Press x, ?/1 and turn volume to the left at the same time.	24
Messages	24
Precautions	26
On operating voltage	26
On safety	26
On placement	26
On heat buildup	26
On operation	26
Notes on discs	26
Cleaning the cabinet	26
To save a tape permanently	27
Before placing a cassette in the tape deck	27
When using a tape longer than 90minutes	27
Cleaning the tape heads	27
Demagnetizing the tape heads	27
Specifications	27