Sony ECM-100N Operating Instructions

















English

Electret Condenser Microphone

Before using the microphone, please read this manual thoroughly. This manual should be

retained for future reference.

The validity of the CE marking is restricted to only those countries where it is legally

enforced, mainly in the countries EEA (European Economic Area).

Names and Functions of Parts (Fig.



)

(The numbers refer to the corresponding numbers in the figure.)



Microphone



PAD switch

Select the PAD switch to the level of input source.

:

Off

: On



LOW CUT switch

The low cut filter reduces the wind noise effectively.

: Normal setting

: The low cut filter is applied.



Output connector (XLR-3-12C type)

The sound recorded with the microphone is output. The power is supplied to the

microphone from an external equipment through this connector when the microphone

is operating on the external power supply.



Wind screen

Attach to the microphone



to reduce wind or breathing noise.



Microphone holder

When using a microphone stand (not supplied), for example, attach the holder to the

microphone. When the angle adjustment screw has become loose, tighten it with a coin.

A stand adaptor is equipped to the microphone holder. If you do not plan on using the

stand adaptor, detach it, and then attach it to a microphone stand (sold separately).



Stand adaptor

Power Supply

This microphone is powered only from an external power supply. Connect output connector



of the microphone to the microphone connector of a Phantom power supply (external

power supply) or an audio mixer. For connection, use a microphone cable.

Note

An unbalanced cable cannot be connected to this microphone.

Be sure to use a balanced

microphone cable.

Notes on Use

•

Microphones are delicate. Do not drop or subject it to excessive shock.

•

Avoid extended usage or storage in high humidity or temperatures above 60 °C (140 °F).

It may cause noise or failure.

•

If acoustic feedback occurs during use (a howling sound is heard from the speakers),

point the microphone away from the speakers or increase the distance between the

microphone and the speakers.

•

The microphone output signal is a balanced output. Unbalanced output is not supported,

so be sure to connect it to the balanced input circuit.

•

A cable with the connector housing part connected to the ground wire (pin 1) is

recommended for the microphone cable.

Cables that are not connected to a ground wire may emit noise.

If a ground terminal is available, noise can be reduced by connecting to that terminal.

Also, if used extending several microphone cables and the connector housing part

touches the floor, noise may worsen.

Specifications

General

Type

Electret condenser

Power supply

External power supply operation 44 V to 52 V DC (IEC* 61938 P48)

Power consumption

Less than 2.5 mA

Output connector

XLR-3-12C Type

Dimensions

19 mm dia. × 130 mm (0.75 in. dia. × 5.12 in.)

Mass

Approx. 130 g (4.6 oz)

Supplied accessories

Microphone holder (1)

Wind screen (1)

Stand adaptor (W3/8 - NS5/8) (1)

Carrying case (1)

Operating instructions (this sheet) (1)

Warranty card (1)

Performance

Frequency response

20 Hz - 50,000 Hz

Directivity

Uni-directional (ECM-100U)

Omni-directional (ECM-100N)

Output impedance

100 Ω ±15%, balanced

Sensitivity

-41 dB (ECM-100U)

-36 dB (ECM-100N)

(deviation±3 dB)

(0 dB=1 V/Pa, 1 kHz)

Inherent noise

Less than 21 dB SPL

(0 dB=2 × 10

-5

Pa)

(IEC* 61672-1 A-Weighted, 1 kHz, 1 Pa)

Maximum input sound pressure level

More than 142 dB SPL (ECM-100U)

More than 145 dB SPL (ECM-100N)

(output level for 1% waveform distortion at 1 kHz, converted into

equivalent input sound pressure level: 0 dB=2 × 10

-5

Pa)

Dynamic range

More than 121 dB (ECM-100U)

More than 124 dB (ECM-100N)

PAD

0 dB/-10 dB (switchable)

LOW CUT filter

Flat/30 Hz (switchable)

* IEC = International Electrotechnical Commission

Design and specifications are subject to change without notice.

Note

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE

FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR

REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE

TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION

OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Electret Condenser

Microphone

Operating Instructions

GB

Mode d’emploi

FR

ECM-100U / ECM-100N

4-735-086-

12

(1)

©2018 Sony Corporation

Printed in Japan

http://www.sony.net/

Sony ECM-100N Operating Instructions

Sony ECM-100N Manual

Sony ECM-100N manual content summary: