Sony KDL-40WL135 Installing the Wall-Mount Bracket (SU-WL500)

Align the tab on the rear of the Mounting Hook

with the square hole on the rear of the TV as in

the illustration below.

Note

Be sure not to use any screws other than the supplied

ones (+PSW6

×

16) when securing the Mounting

Hook.

4

Adjust the angle of the Mounting

Hook using the hexagon wrench

supplied with the Wall-Mount

Bracket.

When installing the TV parallel to the wall (0

degrees), adjustment of the Mounting Hook

angle (procedures

1

and

2

below) is not

necessary. Make sure that each arm base

X

is

screwed in securely.

1

Remove the two screws from the arm base

X

of the Mounting Hook. Choose the holes

corresponding to the desired angle (5, 10, 15

or 20 degrees).

2

Adjust the angles of the top

Y

and bottom

Z

arm to fit the corresponding hole, and

firmly secure each arm using the two screws

removed in the previous procedure

1

.

Installing the Wall-Mount Bracket

To Customers

For product protection and safety reasons, Sony strongly recommends that wall-mounting of your TV

be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

Your KDL-40WL135/KDL-46WL135/KDL-52WL135 can be wall-mounted using the SU-WL500

Wall-Mount Bracket (sold separately). Please provide your licensed contractor with this installation

supplement as well as the instructions (supplied with the SU-WL500 Wall-Mount Bracket). Read these

documents carefully for safety and proper installation.

To Sony Dealers and Contractors

Provide full attention to safety during the installation, periodic maintenance and examination of this

product.

3-295-908-

12(1)

© 2007 Sony Corporation

Step 1: Checking the parts

required for the

installation

Open the Wall-Mount Bracket package and check the

contents for all required parts along with the

Instructions.

Step 2: Deciding on the

installation location

Decide where you want to install your TV. Refer to

the reverse page for the TV installation dimensions

table.

Refer to the Instructions for SU-WL500.

Step 3: Installing the Base

Bracket on the wall

Refer to the Instructions for SU-WL500.

Installing the TV on a wall

The TV can be installed on a wall by attaching a Wall-

Mount Bracket (sold separately).

Verify your TV’s model number and be sure to use

the bracket specified for your model only. Refer to the

steps on this leaflet along with the instructions

supplied with the SU-WL500 Wall-Mount Bracket, to

properly carry out the installation.

Sufficient expertise is required in installing this

product, especially to determine the strength of

the wall for withstanding the TV’s weight. Be

sure to entrust the attachment of this product to

the wall to Sony dealers or licensed contractors

and pay adequate attention to safety during the

installation. Sony is not liable for any damage or

injury caused by mishandling or improper

installation.

For product protection and safety reasons, Sony

strongly recommends that you use the Wall-

Mount Bracket model designed for your TV and

that the wall-mounting of your TV is performed by

Sony dealers or licensed contractors.

Printed in Mexico

Step 4: Preparing for the

installation of the TV

Follow the steps below to prepare for installing the

TV.

1

Disconnect all the cables from the

TV.

2

Start removing the screws behind

the TV.

Do not remove any other screws from the TV.

3

Secure the Mounting Hook to the

rear of the TV.

Referring to the Screw and Hook locations

diagram/table on the reverse page, determine

the screw positions, and secure the Mounting

Hook to the rear of the TV.

1

Secure the Mounting Hook to the rear of the

TV temporarily, using the supplied four

screws (+PSW6

×

16).

2

Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

Notes

•

Be sure to adjust the right and left arms to the same

angle.

•

Make sure that the two arm bases are screwed in

securely.

CAUTION

Be careful not to pinch your fingers when

adjusting the angle of the Mounting Hook.

5

Lift the TV off the stand. Make

sure that you carry out this task

with at least two or three people.

Do not attempt to lift the TV by yourself.

Step 5: Installing the TV on the

wall

Refer to the instructions for SU-WL500.

Notes

•

When you put the TV back on the stand, reverse the

above steps (insert the posts of the stand, aligning with

the lines on the rear of the TV).

•

When moving the TV, do not squeeze the bottom of the

front panel too strongly.

•

Remove the screws or install the Mounting Hook on a

stable and level surface.

Screw

(+PSW6

×

16)

Mounting Hook

Square hole

Square

hole

Tab

Hexagon wrench

KDL-52WL135

KDL-40WL135

KDL-46WL135

Sony KDL-40WL135 Installing the Wall-Mount Bracket (SU-WL500)

Sony KDL-40WL135 - 40" Bravia Wl-series Lcd Television Manual

Sony KDL-40WL135 manual content summary: